OKI C710n User Manual

							41 – C710n User’s Guide
PCL 
Setup 
(cont.)White 
Page skipOn/OffSets whether to eject a page 
without any data to print (blank 
page) upon reception of FF 
command (OCH) in PCL Mode. 
OFF: Ejecting.
CR 
FunctionCR/CR+LFSets action when CR code is 
received in PCL.
CR: Carriage Return 
CR+LF: Carriage Return and 
Line Feed
LF 
FunctionLF/LF+CRSets action when LF code is 
received in PCL.
LF: Line Feed 
LF+CR: Line Feed and Carriage 
Return
Print 
MarginNormal
1/5 inch
1/6 inch
Sets a non-printable area of 
paper.
The width of the area along the 
right and left sides of paper 
(left and right sides depend on 
paper orientation).
NORMAL: PCL emulation 
compatible, approximately 1/
4~1/4.3INCH (depending on 
paper) is outside the printable 
area.
Tr u e 
Black
On/OffSets whether to use Composite 
Black (cmyk mixed) or Pure 
Black (K only) for the black 
(100%) in image data.
OFF: Mode using Composite 
Black
ON: Mode using Pure Black
(PCL only)
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							42 – C710n User’s Guide
PCL 
Setup 
(cont.)
)
Pen Width 
Adjust
On/OffWhen minimum width is 
specified in PCL, sometimes a 
1-dot line, looks broken.
With PEN WIDTH Adjust set to 
ON, when the minimum width is 
specified, the line width will be 
emphasized so as to look wider 
than a 1-dot line.
With PEN WIDTH Adjust set to 
OFF, the line will appear as 
before.
Tr a y  2  I D #1 ~ 5 ~ 59Sets the # to specify Tray 2 for 
the paper feed destination 
command (ESC&l#H) in PCL5e 
emulation.
(Displayed only if Tray 2 is 
installed).
Tr a y  3  I D #1 ~ 20 ~ 59Sets the # to specify Tray 3 for 
the paper feed destination 
command (ESC&l#H) in PCL5e 
emulation.
(Displayed only if Tray 3 is 
installed).
MPTray 
ID#1 ~ 4 ~ 59Sets the # to specify the MP 
tray for the paper feed 
destination command 
(ESC&l#H) in PCL5e emulation.
IBM PPR 
SetupCharacter 
Pitch10 CPI
12 CPI
17 CPI
20 CPI
Proportional
Specifies character pitch in IBM 
PPR emulation.
Font 
Condense12CPI to 
20CPI
12CPI to 12CPI
Specifies 12CPI pitch for 
Condense Mode.
Character 
SetSET-2
SET-1
Sets a character set.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							43 – C710n User’s Guide
IBM PPR 
Setup 
(cont.)Symbo 
SetIBM 437Sets the Symbol Set for IBM 
PPR (see machine operator 
panel for complete list).
Letter O 
StyleEnable/
DisableSpecifies the style that replaces 
ø (9B) and ¥ (9D) with ø (ou) 
and Ø (zero).
Zero 
CharacterNormal/
SlashedSpecifies the style of 0(zero). 
SLASHED: SLASH ZERO
Line Pitch6/8 LPISets line space.
White 
Page SkipOn/OffSets whether to eject a blank 
sheet. Available only when 
simplex is set.
CR 
FunctionCR/CR+LFSets action when CR code is 
received.
LF 
FunctionLF/LF+CRSets action when LF code is 
received.
Line 
Length80/136 
ColumnSpecifies the number of 
characters per line.
Form 
Length11/11.7/12 
inchSpecifies the length of paper.
TOF 
Position0.0/0.1/~1.0 
inchSets the position from the top 
edge of paper.
Left 
Margin0.0/0.1/~1.0 
inchSets the amount to shift the 
horizontal print start position to 
the right.
Fit to 
LetterEnable/
DisableSets the printing mode that can 
fit print data, equivalent to 11 
inches (66 lines), in the 
LETTER-size printable area.
Te x t  
HeightSame/DiffSets height of a character.
SAME: Regardless of CPI, same 
height
DIFF: According to CPI, 
character heights vary.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							44 – C710n User’s Guide
EPSON 
FX SetupCharacter 
Pitch10 CPI/12 
CPI/17 CPI
20 CPI/
Proportional
Specifies character pitch in 
Epson FX emulation.
Character 
SetSET-2
SET-1
Sets a character set.
Symbol 
SetIBM 437Sets the Symbol Set for Epson 
FX Emulation.
(see machine operator panel for 
complete list).
Letter O 
StyleEnable/
DisableSpecifies the style that replaces 
ø (9B) and ¥ (9D) with ø (ou) 
and Ø (zero).
Zero 
CharacterNormal/
SlashedSpecifies the style of 0(zero). 
SLASHED: SLASH ZERO
Line Pitch6/8 LPISets line space.
White 
Page SkipOn/OffSets whether to eject a blank 
sheet. Available only when 
simplex is set.
CR 
FunctionCR/CR+LFSets action when CR code is 
received.
Line 
Length80/136 
ColumnSpecifies the number of 
characters per line.
Form 
Length11/11.7/12 
inchSpecifies the length of paper.
TOF 
Position0.0/0.1/~1.0 
inchSets the position from the top 
edge of paper.
Left 
Margin0.0/0.1/~1.0 
inchSets the amount to shift the 
horizontal print start position to 
the right.
Fit to 
LetterEnable/
DisableSets the printing mode that can 
fit print data, equivalent to 11 
inches (66 lines), in the 
LETTER-size printable area.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							45 – C710n User’s Guide
EPSON 
FX Setup 
(cont.)Te x t  
HeightSame/DiffSets height of a character.
SAME: Regardless of CPI, same 
height
DIFF: According to CPI, 
character heights vary.
Color 
SetupInk 
Simulation
Off
SWOP
Euroscale
Japan
The machine has its own 
process simulation engine 
which simulates standard colors 
in the printer.
This function is available only 
with PS language jobs.
UCRLow
Medium
High
Selects limitation to the toner 
layer thickness.
If paper curl occurs in dark 
printing, selecting MEDIUM or 
LIGHT sometimes helps reduce 
this curl.
UCR = Under Color Removal.
CMY 
100%
Density
Enable/
DisableEnable/Disable 100% output 
against the CMY100% TRC 
compensation. Ordinarily, the 
TRC compensation function 
holds control for the 
appropriate print density; thus 
100% output is not always 
possible.
Selecting ENABLE will enable 
100% output in any individual 
color. The actual print, including 
the TRC compensation function 
is limited to an appropriate 
area. This function is for special 
purposes such as specification 
in CMYK color reduction in PS.
CMYK 
Conversio
n
On/OffSetting to “OFF” will simplify 
the conversion process of CMYK 
data, which will reduce the 
processing time.
This setting is ignored when Ink 
Simulation function is used.
PS only
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							46 – C710n User’s Guide
Memory 
SetupReceive 
Buffer 
Size
Auto
0.5 megabyte
1 megabyte
2 megabyte
4 megabyte
8 megabyte
16 megabyte
Sets the size of receive buffer
Resource 
Save
Auto
Off
0.5 megabyte
1 megabyte
2 megabyte
4 megabyte
8 megabyte
16 megabyte
Sets the size of resource saving 
area.
HDD 
Setup
This item 
is 
displayed 
only if a 
HDD 
(option) 
is 
installed
.
InitializeExecuteInitializes the HDD to the 
factory default setting. Machine 
performs partition-division, and 
initializes each partition.
When this menu is executed, 
the following confirmation 
message appears.
A r e  Yo u  S u r e ?  Ye s / N o
If No is selected, you will return 
to the previous menu.
If Yes is selected, the following 
confirmation message appears.
Execute Now? Yes/No
If No is selected, you will return 
to the previous menu.
The request to execute HDD 
initialization is put into the 
memory and initialization will 
be executed at the next power 
cycle.
If Yes is selected, shutdown 
takes place, and the HDD is 
initialized at power Off/On 
cycle.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							47 – C710n User’s Guide
HDD 
Setup 
(cont.)Resize 
PartitionPCL nn%/
Common 
mm%/PSll%/
Specifies the size of partition. 
Specifies a size by ratio to the 
whole HDD in % (1% unit).
nn,mm,ll: 1 - 98 and 
nn+mm+ll=100
The sizes are displayed in the 
partition list and can be 
changed by selecting the 
partition size to be changed. If 
Apply is selected, the following 
confirmation message appears.
Are You Sure? Yes/No
No = return to the previous 
menu.
Yes = Execute Now? Yes/No
No = return to the previous 
menu. The request is put into 
the memory and the hard disk 
initialization and partition size 
change will be executed at next 
power cycle.
Yes = shutdown. Hard disk 
initialization and partition size 
change will be executed at 
Power Off/On cycle.
In Non-PS machines, PS is 
replaced by COMMON, so the 
message is displayed as “PCL/
COMMON/COMMON”.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							48 – C710n User’s Guide
HDD 
Setup 
(cont.)Format 
PartitionPCL
Common
PS
Formats a specified partition.
When the Enter button is 
pressed, the following 
confirmation message appears.
Are You Sure? Yes/No
No =l return to the previous 
menu.
Yes = Execute Now? Yes/No
No i=l return to the previous 
menu. The request to execute 
partition formatting is put into 
the memory and formatting will 
be executed at next power 
cycle.
Yes =shutdown. The partition 
is formatted at power Off/On 
cycle.
In Non-PS machines, PS is 
replaced by Common, so the 
message is displayed as “PCL/
Common/Common”.
System 
SetupNear Life 
LEDEnable/
DisableControls the settings of the 
Attention LED when near end 
of life warning of toner, drum, 
fuser, or belt occurs.
Attention LED is lit when 
enabled, not lit if disabled. 
(Displays LCD message.)
The temporary recovery by 
opening and closing of the 
cover in Life error is not 
included.
Reset 
Section 
CounterExecuteResets the section counter of 
print statistics function to zero.
If Execute is selected, exits 
from the menu.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							49 – C710n User’s Guide
Change 
PasswordNew 
Passwordxxxxxxxxxxxx
xxSets a new password to enter 
Admin Setup menu
From 6 to 12 alpha/numeric 
digits can be entered.
Ver ify  
passwordxxxxxxxxxxxx
xxForces the User to input the 
new password to enter Admin 
Setup.
From 6 to 12 alpha/numeric 
digits can be entered.
SettingsReset 
Settings
ExecuteResets EEPROM of CU. Resets 
User menu to the factory 
default.
If Execute is selected, exits 
from the menu.
Save 
Settings
ExecuteSaves menus currently set. 
With this function, the menus 
with which operation was last 
performed are saved, and 
overwrites with them menus 
that were previously saved.
When the Enter button is 
pressed, the following 
confirmation message appears.
Are You Sure? Yes/No
No = the preceding menus are 
restored.
Yes =, the current menu 
settings are saved and this 
menu is exited.
ITEMSETTINGSEXPLANATION
Downloaded From ManualsPrinter.com Manuals 
						

							50 – C710n User’s Guide
Calibration
ITEMSETTI
NGSEXPLANATION
Auto DensityOn/OffEnables/disables automatic 
density adjustment.
Adjust 
DensityExecuteIf Execute is selected, the 
printer will immediately adjust 
density and reflect it in TRC 
compensation.
This adjustment must be 
executed when the printer is 
idling. It can become invalid 
if executed in any other 
state.
Adjust 
RegistrationExecuteWhen this menu is selected, the 
printer performs AutoAdjust 
Registration.
This adjustment must be 
executed when the printer is 
idling. 
Print Tuning 
PatternExecutePrints the pattern for the user 
to adjust TRC. Ordinarily, this 
function is not needed because 
TRC is automatically adjusted to 
the recommended levels 
through density adjustment and 
TRC compensation.
Adjustment results will be 
reflected as offset values 
(addition) to the corrections 
through the Adjust Density/TRC 
Compensation function.
Downloaded From ManualsPrinter.com Manuals