Home > Oki > Printer > OKI C5900N User Manual

OKI C5900N User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual OKI C5900N User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 103 Oki manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Menu functions> 131
    TRUE BLACKOFF / ONSelects whether black image data 
    is printed using black toner (ON) 
    or 100% CMY (OFF). (Valid in PCL 
    emulation mode only.)
    PEN WIDTH 
    ADJUST
    Tr a y  I D #
    MP TRAY4
    ITEMSETTINGSEXPLANATION
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Menu functions> 132
    PPR EMULATION
    This menu controls settings effective when the printer is 
    operating in PPR emulation mode.
    ITEMSETTINGSEXPLANATION
    CHARACTER 
    PITCH10 CPI; 12 CPI; 17 
    CPI; 20 CPI; 
    PROPORTIONALSpecifies character pitch in IBM 
    PPR emulation.
    FONT 
    CONDENSE12CPI - 20CPI; 
    12CPI - 12CPISpecifies 12CPI pitch for Condense 
    Mode.
    CHARACTER 
    SETSet 1; Set 2Specifies a character set.
    SYMBOL SETIBM 437Specifies a symbol set.
    LETTER 0 
    STYLEDisable; Enable Specifies the style that replaces 
    9BH with letter o and 9DH with a 
    zero
    ZERO 
    CHARACTERNormal; SlashedSets the zero to be slashed or 
    unslashed.
    LINE PITCH 6 LPI; 8 LPI Specifies the line spacing.
    WHITE PAGE 
    SKIPOFF / ONSelects whether blank pages are 
    printed or not.
    CR FUNCTIONCR / CR+LF Selects whether a received 
    carriage return character (0Dh) 
    also causes a line feed.
    LF FUNCTIONLF / LF+CRSelects whether a received line 
    feed character (0Ah) also causes a 
    carriage return.
    LINE LENGTH80 COLUMN; 136 
    COLUMNSpecifies the number of characters 
    per line.
    FORM 
    LENGTH11 Inch; 11.7 Inch
    12 InchSpecifies the length of paper.
    TOF 
    POSITION0.0 INCH - 1.0 
    InchSpecifies the distance of print from 
    the top edge of the paper.
    LEFT MARGIN0.0 Inch - 1.0 InchSpecifies the distance of print from 
    the left hand edge of the paper.
    FIT TO 
    LETTERDisable; Enable Sets the printing mode that can fit 
    print data, equivalent to 11 inches 
    (66 lines), in the LETTER-size 
    printable area.
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Menu functions> 133
    TEXT HEIGHTSame; DiffSets the height of a character.
    SAME: Regardless of CPI, same 
    height
    DIFF: As CPI, character heights 
    vary.
    ITEMSETTINGSEXPLANATION
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Menu functions> 134
    FX EMULATION
    This menu controls settings effective when the printer is 
    operating in FX emulation mode.
    ITEMSETTINGSEXPLANATION
    CHARACTER 
    PITCH10 CPI; 12 CPI; 17 
    CPI; 20 CPI; 
    PROPORTIONALSpecifies character pitch in this 
    emulation.
    CHARACTER 
    SETSet 1; Set 2Specifies a character set.
    SYMBOL SET IBM 437 Specifies a symbol set.
    LETTER 0 
    STYLEDisable; EnableSpecifies the style that replaces 
    9BH with letter o and 9DH with a 
    zero
    ZERO 
    CHARACTERNormal; Slashed Sets the zero to be slashed or 
    unslashed.
    LINE PITCH6 LPI; 8 LPISpecifies the line spacing.
    WHITE PAGE 
    SKIPOFF / ON Selects whether blank pages are 
    printed or not.
    CR FUNCTIONCR / CR+LFSelects whether a received 
    carriage return character (0Dh) 
    also causes a line feed.
    LINE LENGTH80 COLUMN; 136 
    COLUMNSpecifies the number of characters 
    per line.
    FORM 
    LENGTH11 inch; 11.7 inch;
    12 inchSpecifies the length of paper.
    TOF 
    POSITION0.0 inch  -  1.0  inch Specifies the distance of print from 
    the top edge of the paper.
    LEFT MARGIN0.0 inch - 1.0 inchSpecifies the distance of print from 
    the left hand edge of the paper.
    FIT TO 
    LETTERDisable; Enable Sets the printing mode that can fit 
    print data, equivalent to 11 inches 
    (66 lines), in the LETTER-size 
    printable area.
    TEXT HEIGHTSame; DiffSets the height of a character.
    SAME: Regardless of CPI, same 
    height.
    DIFF: As CPI, character heights 
    vary.
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Menu functions> 135
    USB MENU
    This menu controls the operation of the printer’s USB data 
    interface.
    NETWORK MENU
    This menu controls the operation of the printer’s 10Base-T/
    100Base-TX network interface.
    ITEMSETTINGSEXPLANATION
    SOFT RESET ENABLE / 
    DISABLEEnables or disables the SOFT RESET 
    command.
    SERIAL NUMBERENABLE / 
    DISABLE
    OFFLINE 
    RECEIVEENABLE / 
    DISABLE
    SPEED12 / 480 MpsSelects the interface speed
    ITEMSETTINGSEXPLANATION
    TCP/IPENABLE / 
    DISABLEEnables or disables this network 
    protocol.
    IP VERSIONIP V4 / IPV 4 & 
    V6
    NETBEUIENABLE / 
    DISABLEEnables or disables this network 
    protocol.
    NETWAREENABLE / 
    DISABLEEnables or disables this network 
    protocol.
    ETHERTALKENABLE / 
    DISABLEEnables or disables this network 
    protocol.
    FRAME TYPEAUTO / 802.2 / 
    802.3 / 
    ETHERNET II / 
    SNAPSelects the Ethernet MAC layer 
    frame type.
    IP ADDRESS 
    SETAUTO / MANUAL Specifies whether IP address 
    allocation is automatic (DHCP) or 
    manually assigned.
    IP ADDRESSxxx.xxx.xxx.xxxCurrent assigned IP address. To 
    change, press ENTER and use 
    +/– 
    keys to increment 1st octet, then 
    press ENTER again to move on to 
    next octet. When 4th octet has been 
    set, press ENTER again to register 
    new address.
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Menu functions> 136
    MAINTENANCE MENU
    This menu provides access to various printer maintenance 
    functions.
    SUBNET MASK xxx.xxx.xxx.xxx Current assigned subnet mask. To 
    change, proceed as above.
    GATEWAY 
    ADDRESSxxx.xxx.xxx.xxxCurrent assigned gateway address. 
    To change, proceed as above.
    FAC TO RY 
    DEFAULTSEXECUTE Reloads the settings present when 
    the unit was setup by the 
    manufacturer.
    WEBENABLE / 
    DISABLEEnables or disables Web config. 
    facility.
    TELNET ENABLE / 
    DISABLEEnables or disables Telnet config. 
    facility.
    FTPENABLE / 
    DISABLEEnables or disables communication 
    via FTP.
    SNMPENABLE / 
    DISABLEEnables or disables SNMP protocol.
    NETWORK 
    SCALENORMAL / 
    SMALLSelects network size.
    HUB LINK 
    SETTINGAUTO 
    NEGOTIATE
    100BASE-TX 
    FULL
    100BASE-TX 
    HALF
    10BASE-T FULL
    10BASE-T HALFSets full or half duplex for 
    communication via a network hub.
    ITEMSETTINGSEXPLANATION
    ITEMSETTINGSEXPLANATION
    MENU RESET EXECUTE Resets menus to default settings.
    SAVE MENUEXECUTESaves current menu settings as 
    default values. At confirmation 
    prompt, press ENTER to confirm 
    save, or CANCEL to cancel.
    POWER SAVEENABLE / 
    DISABLEEnables or disables automatic power 
    save mode. Delay before entering 
    this mode is set in the system 
    configuration menu.
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Menu functions> 137
    USAGE MENU
    This menu is for information only, and provides an indication of 
    total usage of the printer and the expected life left in its 
    consumable items. This is particularly useful if you do not have a 
    full set of replacement consumables to hand and you need to 
    know how soon you will need them.
    PAPER BLACK 
    SETTING–2~0~+2Used for small adjustment when you 
    experience faded print or light 
    specks / streaking in monochrome 
    printing on white paper. Select a 
    higher value to reduce fading, or a 
    lower value to reduce specks or 
    streaking in high density print areas.
    PAPER COLOR 
    SETTING–2~0~+2 As above, but for colour printing.
    TRANSPR 
    BLACK SETTING–2~0~+2As above but for mono printing on 
    transparencies.
    TRANSPR 
    COLOR SETTING–2~0~+2 As above but for colour printing on 
    transparencies.
    ITEMSETTINGSEXPLANATION
    ITEMEXPLANATION
    TRAYn PAGE COUNT The total number of pages fed from tray n.
    MPT PAGE COUNTThe total number of pages fed from the multi 
    purpose tray.
    COLOUR PAGE 
    COUNTThe total number of pages printed in colour.
    MONO PAGE COUNTThe total number of pages printed in 
    monochrome.
    K DRUM LIFE 
    REMAINING
    C DRUM LIFE 
    REMAINING
    M DRUM LIFE 
    REMAINING
    Y DRUM LIFE 
    REMAININGPercentage of life remaining in these consumable 
    items.
    BELT LIFE 
    REMAININGPercentage of belt life remaining.
    FUSER LIFE 
    REMAININGPercentage of fuser life remaining.
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Menu functions> 138
    JOB LOG MENU
    K TONER
    C TONER
    M TONER
    Y TONER
    Cartridge size and current toner level.
    ITEMSETTINGEXPLANATION
    JOB LOG ENABLE/
    DISABLEPrints a list of jobs carried out 
    on this printer.
    ITEMEXPLANATION
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Overlays and Macros (Windows only)> 139
    OVERLAYS AND MACROS (WINDOWS ONLY)
    WHAT ARE OVERLAYS AND MACROS?
    If you would like to print on special stationery, such as forms and 
    letterhead, but do not want to use pre-printed stationery, you 
    can create your own using these advanced features.
    You can use PostScript overlays to generate all your special 
    stationery and store it in the printer for use whenever you need 
    it. If you have chosen to install the PCL driver, macros perform a 
    similar function.
    You can create several overlays or macros, and combine them in 
    any way you like to produce a variety of forms and other special 
    stationery. Each image can be printed on just the first page of a 
    document, on all pages, on alternate pages, or just the pages 
    that you specify.
    NOTE:
    PostScript overlays are not available for Windows 95/98/Me.
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Overlays and Macros (Windows only)> 140
    CREATING POSTSCRIPT OVERLAYS
    Three steps are required to create an overlay:
    1.Create the form data using your own application software 
    and print it to a printer (.PRN) file.
    2.Use the Storage Device Manager utility software supplied 
    on CD with your printer to create a “project file,” import 
    the.PRN file(s), and download the generated filter (.HST) 
    file to the printer. The project file will contain one or more 
    overlay images which are functionally related, such as the 
    cover page and the continuation page images for business 
    letters.
    3.Use downloaded files to define your overlays ready for use 
    when printing your documents.
    When printing overlay files to disk, do not select any special 
    features, such as two-sided printing or multiple copies. These are 
    not appropriate to overlays, they apply only to your final 
    documents.
    CREATING THE OVERLAY IMAGE
    1.Use your preferred application, perhaps a graphics 
    program, to create the required overlay image and save 
    it.
    2.Open your 
    application’s Print… 
    dialogue.
    3.Make sure that the 
    selected printer 
    name (1) is that of 
    your PostScript 
    printer driver.
    4.Select the Print To 
    File(2) option.
    5.Click the Properties button (3) to open the Document 
    Properties window.
    13
    2
    Downloaded From ManualsPrinter.com Manuals 
    						
    All Oki manuals Comments (0)

    Related Manuals for OKI C5900N User Manual