OKI C5900CDTN User Manual

							Installing upgrades> 171
9.If the RAM expansion slot already contains a memory 
upgrade board, that board will have to be removed before 
you can install the new one. To remove it, proceed as 
follows, otherwise skip to step 10.
(a)Grip the board firmly by its short edges and pull it 
out of the slot.
(b)Place the removed memory board in the antistatic 
bag which originally contained the new memory 
board.
10.Hold the new memory board by its short edges, so that 
the edge connector faces in towards the RAM expansion 
slot, and the small cutout is closer to the rear of the 
printer.
11.Gently push the board into the RAM expansion slot until it 
latches in and will not go any further.
12.Locate the three retaining clips at the bottom of the side 
cover into their rectangular holes near the bottom of the 
printer.
13.Close the top of the side cover up to the printer and refit 
the securing screw removed in step 4.
14.Close the front cover and close the top cover, pressing 
down firmly at each side to latch it closed.
15.Reconnect the AC power cable and switch the printer on.
16.When the printer is ready, print a menu map as follows:
(a)Press the + button to access the Information Menu.
(b)Press ENTER once for the menu map.
(c)Press ENTER again to print the menu map.
Downloaded From ManualsPrinter.com Manuals 
						

							Installing upgrades> 172
(d)When the menu map is printed, press ON LINE to 
exit the menu system.
17.Examine the first page of the menu map.
Near the top of the page, between the two horizontal lines, 
you will see the current printer configuration. This list 
contains the figure for total memory size.
This should indicate the total memory now installed.
If you are using the Windows PostScript driver, follow the 
instructions later in this section to adjust the driver.
Downloaded From ManualsPrinter.com Manuals 
						

							Installing upgrades> 173
HARD DISK DRIVE
The optional internal hard disk drive (HDD) enables collating of 
printed pages and can be used to store overlays and macros, 
fonts, and secure or proof documents waiting to be printed.
Installation takes a few minutes, and requires a medium size 
cross-head (philips type) screwdriver.
1.Switch the printer off and disconnect the AC power cable.
2.Press the cover release and open the printer’s top cover 
fully.
3.Lift the front cover latch and pull open the front cover.
4.Remove the screw (1) securing the right-hand side cover.
5.Lift the edge of the side cover slightly at the two points 
shown, and pull the cover away from the printer at the 
WARNING!
If the printer has been powered on recently, the fuser 
will be hot. This area is clearly labelled. Do not touch.
1
Downloaded From ManualsPrinter.com Manuals 
						

							Installing upgrades> 174
top. Lift the cover slightly to detach it from the printer. 
Place it safely to one side.
6.Locate the clip (1)on the top of the disk unit into the slot 
(2) in the printer.
7.Plug the end of the connecting cable (3) into the disk unit 
connector (4) in the printer.
8.Tighten the two thumbscrews (5).
9.Close the top of the side cover up to the printer and refit 
the securing screw removed in step 4.
10.Close the front cover and the top cover, pressing down 
firmly at each side to latch it closed.
11.Reconnect the AC power cable and switch the printer on.
12.When the printer is ready, print a menu map as follows:
(a)Press the + button to access the Information Menu.
(b)Press ENTER once for the menu map.
(c)Press ENTER again to print the menu map.
(d)When the menu map is printed, press ON LINE to 
exit the menu system.
13.Examine the first page of the menu map.
Near the top of the page, between the two horizontal lines, 
you will see the current printer configuration. This should 
now indicate that the hard disk unit is installed.
2
1
3
5
4
5
Downloaded From ManualsPrinter.com Manuals 
						

							Installing upgrades> 175
ADDITIONAL PAPER TRAY
1.Switch the printer off and disconnect the AC power cable.
2.Place additional paper tray on desired location.
3.Observing safety rules for lifting and, using locating 
guides, place printer on top of the additional paper tray. 
4.Re-connect the AC power cable and switch the printer ON.
Downloaded From ManualsPrinter.com Manuals 
						

							Installing upgrades> 176
ADJUSTING WINDOWS PRINTER DRIVERS
Once your new upgrade has been installed, you may need to 
update the Windows printer driver so that the additional features 
are available to your Windows applications.
Remember that if your printer is shared between users on 
different computers, the driver must be adjusted on each user’s 
machine.
The illustrations shown here are for Windows XP. Other Windows 
versions may appear slightly different, but the principles are the 
same.
PCL DRIVER
If you have installed a memory upgrade it is not necessary to 
change the PCL printer driver, and you can ignore this section.
If you have installed a duplex unit or hard disk, proceed as 
follows:
1.Open the Printers window 
(called “Printers and Faxes” in 
Windows XP) via the Start Menu 
or from the Windows Control 
Panel.
2.Right-click the printer icon for 
this printer, and choose 
Properties from the pop-up 
menu.
3.On the Device Options tab, 
check the box for the upgrade 
you have just installed.
4.Click OK to close the properties window, and then close 
the Printers window.
Downloaded From ManualsPrinter.com Manuals 
						

							Installing upgrades> 177
POSTSCRIPT DRIVER
This driver must be adjusted for any upgrade just installed.
1.Open the Printers window 
(called “Printers and Faxes” in 
Windows XP) via the Start 
Menu or from the Windows 
Control Panel.
2.Right-click the printer icon for 
this printer, and choose 
Properties from the pop-up 
menu.
3.On the Device Settings tab, 
locate the list of installable options. Change those settings 
to indicate the new features you have just installed.
4.Click OK to close the properties window, and then close 
the Printers window.
Downloaded From ManualsPrinter.com Manuals 
						

							Clearing paper jams> 178
CLEARING PAPER JAMS
Provided that you follow the recommendations in this guide on 
the use of print media, and you keep the media in good condition 
prior to use, your printer should give years of reliable service. 
However, paper jams occasionally do occur, and this section 
explains how to clear them quickly and simply.
Jams can occur due to paper misfeeding from a paper tray or at 
any point on the paper path through the printer. When a jam 
occurs, the printer immediately stops, and the Alert LED on the 
Status Panel (together with the Status Monitor) informs you of 
the event. If printing multiple pages (or copies), do not assume 
that, having cleared an obvious sheet, others will not also be 
stopped somewhere along the path. These must also be removed 
in order to clear the jam fully and restore normal operation.
MAJOR PRINTER COMPONENTS AND PAPER PATH
1. Duplex unit (if fitted). 6. Operator panel.
2. Face-up stacker.7. Front cover.
3. Paper exit. 8. Paper tray.
4. Fuser unit9. Additional paper tray (if 
fitted)
5. Top cover.


 







Downloaded From ManualsPrinter.com Manuals 
						

							Clearing paper jams> 179
PAPER SENSOR ERROR CODES
* (if fitted).
1.If a sheet is well advanced out of the top of the printer, 
simply grip it and pull gently to draw it fully out. If it does 
not remove easily, do not use excessive force. It can be 
removed from the rear later.
2.Press the cover release and open the printer’s top cover 
fully.
CODE #LOCATIONCODE #LOCATION
370 Duplex unit * 382 Paper exit
371Duplex unit *383Duplex unit *
372 Duplex unit * 390 MP Tray
373Duplex unit *391Paper Tray
380 Paper feed 392
2
nd Paper tray *
381Paper path400Paper size





 




WARNING!
If the printer has been powered on, the fuser will be hot. 
This area is clearly labelled. Do not touch.
Downloaded From ManualsPrinter.com Manuals 
						

							
Clearing paper jams> 180
3.Note the positions of the four cartridges.
It will be necessary to remove the four image drums to gain 
access to the paper path.
4. Holding it by its top centre , lift the cyan image drum, 
complete with its toner cartridge, up and out of the 
printer.
1
2
3
4
1. Cyan cartridge 2. Magenta cartridge
3. Yellow cartridge 4. Black cartridge
Downloaded From ManualsPrinter.com Manuals