OKI B6500 User Manual

B6500 User’s Guide> 91
Job Accounting
The Job Accounting Menu provides access to functions and settings 
related to this feature. Use the following procedure to enter the Job 
Accounting Menu to change the settings or access the functions:
1.Press the MENU button on the control panel.
2.Press the 
 button until the text “Job Accounting” is 
shown on the first line of the display.
3.Press the < > button to enter the Job Accounting Menu.
4.Press the 
 or  buttons to move through the 
submenus.
5.Press the...

B6500 User’s Guide> 92
Spooling
The Spooling Menu provides access to the functions and settings 
related to this feature. Use the following procedure to enter the 
Spooling Menu to change the settings or access the functions:
1.Press the MENU button on the control panel.
2.Press the 
 button until the text “Spooling Menu” is 
shown on the first line of the display.
3.Press the < > button to enter the Spooling Menu.
4.Press the 
 or  buttons to move through the 
submenus.
5.Press the < > button to enter a...

B6500 User’s Guide> 93 Delete
Use to delete a 
spool file from 
the User Flash, 
Disk, or 
Compact Flash.Customer 
SelectableUser Flash
Disk
Compact FlashPress < > or < > to 
select location of file (User 
Flash, Disc, or Compact 
Flash).
Press < > to enter the 
location.
Press < > or < > to 
select the file.
Press  to delete 
the file.
Destination
The spooling 
feature allows 
print jobs to be 
automatically 
spooled to the 
Flash memory 
or Hard Drive.Customer 
SelectableUser Flash
Disk
Compact...

B6500 User’s Guide> 94
Troubleshooting
When Paper Jams
CAUTION
•When removing jammed paper, make sure that no 
pieces of torn paper are left in the machine. A piece 
of paper remaining in the machine can cause fire. If a 
sheet of paper is wrapped around the heat roller, or 
when clearing a jammed paper that is difficult or 
impossible to see, do not try to remove it by yourself. 
Doing so can cause injuries or burns. Switch off the 
machine immediately, and contact your dealer or 
service. 
Following...

B6500 User’s Guide> 95
1.Open cover A, and 
holding the drum/toner 
cartridge by the grip, 
remove it from the 
printer (1). 
2.Turn the roll as shown in 
the diagram and remove 
any jammed paper inside 
(2). 
3.Return the drum/toner 
cartridge and cover A to their original positions. 
NOTE
>When the optional offset catch tray is installed, close 
cover A first before returning the tray to its original 
position. 
>If you continue to print with the offset catch tray folded, 
this may cause a paper jam....

B6500 User’s Guide> 96
Pulling out paper trays
1.Pull out all paper trays and 
remove any wrinkled paper. 
2.Examine the inside of the 
printer and remove any 
jammed paper. 
After removing paper,
1.Push the paper trays 
completely back into the 
printer. 
2.Open and close cover A. 
Doing this will clear the error 
message. 
Cover B
Remove the rear tray when opening the 
back cover.
Raise the lever as shown in the diagram 
and open the cover B (1). After opening 
cover B, open the cover of the fuser unit...

B6500 User’s Guide> 97
Cover C
Duplex unit
Remove the rear tray when opening the 
back cover.
Push up the lever shown in the diagram to 
open the cover.
Cover D
Offset catch tray
Downloaded From ManualsPrinter.com Manuals 

B6500 User’s Guide> 98
When Problems Occur
Before treating the problem as a machine breakdown, refer to the 
following table and check the printer condition again. 
WARNING
•Never open or remove machine covers that are secured with screws 
unless specifically instructed in the user guide. A high voltage 
component can cause electric shock. 
•Do not try to alter the machine configuration, or modify any parts. 
An unauthorized modification can cause smoke or fire. 
NOTE
>Information on incorrect print...

B6500 User’s Guide> 99 Cannot print.  Is the light of the  indicator off ? If so, this printer is 
off-line or in menu setting mode. Fix the problem according to 
the following display status:
“Off-line”  
Press the  button to exit the off-line mode. 
Others  
Press the  button to exit the menu setting mode. 
“Main Components and Their Functions” on page 9
Is there a message displayed on the control panel? Follow the 
message to rectify the problem. 
“Message List” on page 108
When a parallel cable is...

B6500 User’s Guide> 100 Light of 
 
indicator is 
blinking. An error that you cannot rectify yourself has occurred. Record 
the displayed error message or error code, switch off the 
power, pull out the power plug from the outlet, and then 
contact service. 
Although no 
print job is sent, 
the message 
“Printing” is 
displayed on the 
control panel 
(when using the 
parallel 
interface). Did you switch on the power of the computer after switching 
on the power to the printer? Pressing the  button...