OKI B4350n User Manual

OPERATION > 61
Advanced tab
1. You can specify which times of day your printer will be available.
2. Indicates current priority, from 1 (lowest) to 99 (highest). Highest 
priority documents will print first.
3. Specifies that documents should be spooled (stored in a special 
print file) before being printed. The document is then printed in 
the background, allowing your application program to become 
available more quickly. Options follow:
This specifies that printing should not start until the last page...

OPERATION > 62
further use until the print job is complete. This requires less disk 
space on your computer, since there is no spool file.
5. Directs the spooler to check the document setup and match it to 
the printer setup before sending the document to print. If a 
mismatch is detected, the document is held in the print queue and 
does not print until the printer setup is changed and the document 
restarted from the print queue. Mismatched documents in the 
queue will not prevent correctly matched...

OPERATION > 63
10. You can design and specify a separator page that prints between 
documents. This is particularly useful on a shared printer to help 
each user find their own documents in the output stack.
Device Options tab
In this window you can select which optional upgrades are installed on 
your printer. See the chapter entitled “Installing Options.”
NOTE
The above features are provided by the Windows 2000 operating system and 
will vary with other operating systems.
Downloaded From...

OPERATION > 64
PS emulation 
For B4350 and B4350n printers with the PostScript 3 option installed.
The main tabs are the General Tab, Advanced Tab and Device Settings 
Tab. The General and Advanced tabs are the same as for PCL emulation 
described earlier.
Device Settings tab
1. You can set the desired paper sizes in each of the available paper 
feed trays.
2. You can make a variety of font settings depending on your 
application.
3. You can set which optional upgrades are installed on your printer. 
See...

OPERATION > 65
PRINTER SETTINGS IN MACINTOSH
Refer to the readme file on the drivers CD, and the online help provided 
in the driver software.
Downloaded From ManualsPrinter.com Manuals 

CONSUMABLES AND MAINTENANCE > 66
CONSUMABLES AND 
MAINTENANCE
This section deals with the replacement of the toner cartridge and image 
drum and general maintenance.
CONSUMABLE ORDER DETAILS
* typical for continuous printing
Please always use genuine Oki consumables. 
TONER CARTRIDGE LIFE
How long your toner cartridge lasts depends on the print coverage; the 
percentage of the page that prints black. A typical letter has 3% to 5% 
print coverage; graphics usually have higher coverage. Higher print...

CONSUMABLES AND MAINTENANCE > 67
WHEN TO REPLACE THE TONER CARTRIDGE
B4100, B4250
Replace the toner cartridge after Toner Low displays in the printer Status 
Monitor. Also, the Error LED indicator slowly blinks when toner is low. 
After Toner Low displays, the printer will print about 100 more pages 
then display Toner Empty and stop printing. Printing will resume after a 
new toner cartridge has been installed.
B4350, B4350n
When the toner is running low, TONER LOW is displayed in the operator 
panel...

CONSUMABLES AND MAINTENANCE > 68
Switch off the printer and allow the fuser to cool for about 10 minutes 
before opening the top cover.
1. Press the top cover release button and open the printer’s top cover 
fully.
2. Pull the colored lever on the right side of the toner cartridge 
towards the front of the printer to close the cartridge then remove 
the used toner cartridge.
3. Follow the installation instructions on or inside the box containing 
the new toner cartridge to install the new cartridge.
4....

CONSUMABLES AND MAINTENANCE > 69
IMAGE DRUM LIFE
The life of an image drum depends on a number of factors, including 
temperature and humidity, the type of paper used, and the number of 
pages per job.
The image drum should last approximately 25,000 pages continuous 
printing. This number is approximate because different numbers of pages 
are printed each time and the environmental conditions and the paper type 
used may vary.
WHEN TO REPLACE THE IMAGE DRUM
B4100, B4250
When the drum reaches 90% of its...

CONSUMABLES AND MAINTENANCE > 70
1. Press the cover release and open the printer’s top cover fully.
2. Remove the used image drum and toner cartridge.
3. Follow the installation instructions on or inside the box containing 
the new image drum to install the new image drum.
4. Follow the installation instructions on or inside the box containing 
the new toner cartridge to install the new toner cartridge.
5. Gently wipe the LED array surface with the LED lens cleaner that 
came with the new toner...