Nortel Modular Ics 6.0 Programming Record Manual

83
P0992642 03Modular ICS 6.0 Programming Record
 MsgIndicate Select the type of message indicator the ATA-connected device  provides. 
(None, Tone, Lamp).
 IntrusionDetermine what priority an attendant telephone will have to allow a break-in 
by an M1 attendant telephone. To stop break-in, this setting must be higher 
than the attendant level.
 Protect LvlNone, Low, Med, High
 NameEnter a one-to-seven-digit name for the telephone.
 User preferncesThese commands allow you to program the...

84
Modular ICS 6.0 Programming RecordP0992642 03
 Pg Zone All:F610
 Page Zone 1:F611
 Page Zone 2:F612
 Page Zone 3:F613
 Page Zone 4:F614
 Page Zone 5:F615
 Page Zone 6:F616Page internally by zone.
Zone 0 pages all zones.
 Page Spkr:F62Page through an external loudspeaker system.
 Pg All, Spkr:F630
 Page Spkr+1:F631
 Page Spkr+2:F632
 Page Spkr+3:F633
 Page Spkr+4:F634
 Page Spkr+5:F635
 Page Spkr+6:F636Page...

85
P0992642 03Modular ICS 6.0 Programming Record
 Show time:F803Use to display the time and date while on a call.
 Wait:Dial:F804Use to program an external autodial number to cause the system to wait to 
receive dial tone from another system before proceeding with the dialing 
sequence.
 Ringing Call:F807
 Long Tones: F808Use to generate a tone for the period you hold down a button to communicate 
with devices such as faxes and answering machines.
 Call Info:F811Use to...

86
Modular ICS 6.0 Programming RecordP0992642 03
 Voice Deny:F88Use to prevent the set from receiving voice calls.
 MCID:F897ESTI lines only: If service is active from the service provider, this feature 
saves current caller information at the service provider system.
 Language:F*501Select the display language. (501 = first language; 502 = second language; 
503 = third language
 Contrast:F*7Use to adjust contrast of display
 Static time:F806Change the first line of the...

87
P0992642 03Modular ICS 6.0 Programming Record
 Line/set rstrnsAssign restriction filters to certain lines on each set in your system.
 Show line:_Select the line on this telephone for which the restriction will apply.
 Normal
 Night
 Evening
 Lunch
 Sched 4
 Sched 5
 Sched 6For each line, enter the number (two-digit) of the restriction filter to apply 
during normal service and each of the schedules.
 Telco featuresThese commands allow you to program how the...

88
Modular ICS 6.0 Programming RecordP0992642 03
 Auto privacySelect whether a line will be private to the individual on a call, or whether it 
can be shared by other users while a call is in progress. The Privacy setting 
can be suspended for individual calls using the privacy feature (
²¡Ü).
 Trunk modeSelect whether the line operates with disconnect supervision. Auto answer 
and DISA lines must be supervised. This setting does not appear for target 
lines.
 Ans modeSelect whether the line...

89
P0992642 03Modular ICS 6.0 Programming Record
 Restrn filtersThese are sets or groups of restrictions and associated overrides that specify 
the external numbers or feature codes that cannot be dialed from a telephone 
or line.
 Show filter:_Enter the two-digit filter number. 
 Restrn flt 00Filter 00 is pre-set with no restrictions.
 Restrn flt 01First programmable restriction. For each filter, enter up to 99 restrictions.
 DenyEnter the digits you wish to be restricted when...

90
Modular ICS 6.0 Programming RecordP0992642 03
 Sched:NightSelect options for your ringing service. 
 ServiceSelect how you want your service activated.
 Trunk AnswerAllow the telephone to answer incoming calls arriving at  any telephone on the 
system.
 ExtraDialEnter the internal telephone number of the Extra-Dial telephone. This allows 
you to assign an additional Direct-dial telephone in the Norstar system for 
each schedule you use.
 Line settingsSelect ringing service options for...

91
P0992642 03Modular ICS 6.0 Programming Record
 Dest codesDefine which routes are used when a destination code is dialed. 
 Show DstCode:_Up to 500 destination codes are programmable.
Enter up to seven digits of  the  destination  code that you want to use to define 
a route. 
Destination codes must be unique.
A destination code cannot begin with a digit assigned as:
 Call Park prefix
 Direct-dial digit
 same as, or be the start digits of a DN, the DISA DN or the Auto DN
 line pool code
...

92
Modular ICS 6.0 Programming RecordP0992642 03
 Schedule namesThe schedule name is shown on the display of the control telephone when the 
schedule is turned on. It identifies the active schedule.
 Sched 1
 Sched 2
 Sched 3
 Sched 4
 Sched 5
 Sched 6Enter the name of the schedule, or use the default numbering.
 Schedule timesEnter automatic start and stop times for scheduled services. 
 MondayAssign the schedule times for Monday, as it applies to your office.
 Sched:Night...