Nortel Modular Ics 6.0 Installer Guide

Fiber cable management system / 231
P0992638 03Modular ICS 6. 0 Installer Guide
Fiber cable management system
C100 Controller
38 mm (1 1/2 in)
wood screws
Spacer
90  Fiber
cable guideLabel
Fiber Cable 
Guide
Label
Spacer
Fiber Cable 
Guide
38mm (1-1/2 
in) wood screws 

232 / Fiber cable management system
Modular ICS 6.0 Installer GuideP0992638 03
Using the fiber cable management system
To facilitate the installation of an MICS 6.0 or MICS-XC 6.0 
configuration, the Fiber Cable Management System ensures 
that power cords are located outside of the cable tray. It also 
ensures that a 2.6 cm (1 in.) space exists between the ICS 
module and other modules.
The following hardware components are used in the Fiber 
Cable Management System:
Fiber Comb (one per system): The...

Fiber cable management system / 233
P0992638 03Modular ICS 6. 0 Installer Guide
Spacer (three per system): install between the mounting 
brackets of the ICS and an adjacent module. The Spacer 
provides a 2.6 cm (1 in.) space between modules and the 
ICS.
Fiber Spool Holder (six per system): Replaces the trough 
shelf in modules requiring additional fiber spools. Install 
the spool holder in the right side of a Trunk Module.
 
ICS Door Label: Located on the inside of the ICS door, it 
provides space to...

234 / Fiber cable management system
Modular ICS 6.0 Installer GuideP0992638 03
Using the fiber spool 
Fiber
Cable –
alternate
routing
Amphenol
Cable Fiber Cable
Fiber
Spool
Amphenol
Cable –
alternate
routing
Fiber cable
Amphenol 
cable - 
alternate 
routing
Amphenol cableFiber cable - 
alternate routingFiber 
spool 

Fiber cable management system / 235
P0992638 03Modular ICS 6. 0 Installer Guide
Making fiber connections 
MICS-XC 6.0 system
Fiber CableFiber
Spool
Fiber
Cable –
alternate
routing
Fiber Comb
6-port
Expansion
Cartridge6-port 
Expansion 
cabinet
Fiber cableFiber comb
Fiber 
spool
Fiber cable - 
alternate routing 

236 / Fiber cable management system
Modular ICS 6.0 Installer GuideP0992638 03
Routing fiber cables
6 port Expansion Cartridge
Fiber
cable
guide Upward routed fiber cable
Downward routed fiber cable
loose cables 

Connecting the wiring / 237
P0992638 03Modular ICS 6. 0 Installer Guide
Connecting the wiring
This section describes the wire connections for your MICS 
system.
Connecting the wiring to the distribution panel
1. Route the cables through the hole in the ICS cable through 
to the distribution panel.
2. Bundle the cables with cable ties and secure them to the 
wall to support their weight.
3. Connect the telephone and auxiliary equipment wires to 
the appropriate pins on the distribution block (refer to the...

238 / Connecting the wiring
Modular ICS 6.0 Installer GuideP0992638 03
Connecting an ICS with loop start lines
Do not attach central office connections to the ICS 
or Modules until power is connected to the units.
2 ICS extensions 
and auxilia ry
3 ICS lines
25-pair
0.5 mm (24 AWG) 
cables with female 
50-pin connector
to distribution 
panel1 ICS extensions 

Connecting the wiring / 239
P0992638 03Modular ICS 6. 0 Installer Guide
Connecting the wiring for an ICS with T1 or PRI lines
MICS-XC 6.0 system
T1 lines from
Central OfficeT1 or PRI lines from 
Central Office 

240 / Connecting the wiring
Modular ICS 6.0 Installer GuideP0992638 03
Connecting a module
25-pair
0.5 mm (24 AWG)
cables with female
50-pin connector
Close velcro
cable retainerClose velcro cable
retainer
25-pair
0.5mm (24 AWG)
cables with female
50-pin connector