Nitsuko Digital System Phone Program Record Form Manual

Program 1 - Class of Service (contd)
COS Only Intercom Calls at Night
 Off-Premise Call Forward
 Break-In (Intrusion)
 Camp-On (Busy Extension)
 Internal Call Forward
 System Speed Dial
 Toll Restriction Level
 Only Local Calls (Day/Night)
 Only Local Calls at Night
 Extended Ring
 Privacy
 Callback Priority
 Direct Trunk Access/Camp-On
 All Call Page
 Page Zone 1 Access
 Page Zone 2 Access
 Page Zone 3 Access
 Silent Monitor
 No Single Line Flash/ACD Supervisor
 Single Ring for ASI/OPX
 Only CO Call FWD...

Program 2 - Intercom Signaling
Feature NameFeature Data
Call Wait Tones
Handsfree 
Reply
Voice-
Announced 
Calls
Auto Handsfree
To enter Program 2 data:
1. Enter program mode.
# + dial 775312 + #.
2. Press key 2.
3. To accept the displayed data: #.
OR
    To change the displayed data: Dial data + #.
- To erase data before pressing #: Press *.
4. Repeat step 3 for all data.
If you finish and do not see, SAVE TO EXIT: SAVE.
5. Select an option: 
- To enter another program: Press its key.
- To exit program...

Program 3 - Miscellaneous System Features
Feature Name Feature Data Feature Name Feature Data
# Operators Voice Mail
Oper. 01 Ext.Voice Mail 
Master Ext.
Oper. 02 Ext.Dial-Out # in 
Speed Dial
Oper. 03 Ext.Dial 1 Before 
Area Code
Oper. 04 Ext.Walking COS 
Security Code
# System Speed 
Dial DigitsPlay MOH on 
Transfer
Side Tone Test 
DigitAUX Ports 
Baud Rate
To enter Program 3 data:
1. Enter program mode.
# + dial 775312 + #.
2. Press key 3.
3. To accept the displayed data: #.
OR
    To change the...

Program 4 - System Timers
Timer Number Timer Name Duration
01Park Orbit
02Hold Recall
03Camp-On
04Line Response
05Modem Reserve
06# Ring Before Recall
07# Delayed Rings
08Flash Response
09Dial Tone Detect
10Make
11Break
12Interdigit
To enter Program 4 data:
1. Enter program mode.
# + dial 775312 + #.
2. Press key 4.
3. Dial Timer number + #.
4. To accept the displayed data: #.
OR
    To change the displayed data: Dial data + #.
To erase data before pressing #: Press *.
5. Repeat steps 3-4 for remaining...

Program 5 - PBX Trunk Access Codes
ID NumberPBX 
Access 
Code
01
02
03
04
05
06
07
08
09
10
11
To enter Program 5 data:
1. Enter program mode.
# + dial 775312 + #.
2. Press key 5.
3. To accept the displayed data: #.
OR
    To change the displayed data: Dial data + #.
- To enter a wild card: DIAL + dial X (9) + #.
- To erase data: Press * + #.
4. Repeat step 3 for all data.
If you finish and do not see, SAVE TO EXIT: SAVE. 
5. Select an option: 
- To enter another program: Press its key.
- To exit program...

Program 6 - Toll Restriction
Before you fill in data, either use the Copy and Paste commands to make additional copies of the Toll
Restriction forms for each Toll Restriction level you wish to customize or print copies of the blank
forms. You may not need to use all three forms for each level.
Toll Level
 Active Dial Pad
 Special N11 Dialing
 0 + Dialing
 International Dialing
 Equal Access Dialing
 1 + NXX Dialing
 Allow or Deny (See Table #1)
 NXX Dialing
 Allow or Deny (See Table #2)
 NPA Dialing...

Program 6 - Toll Restriction (contd)
Toll Level: Table 4: Allow/Deny Codes For Area Code:
Table 5: Allow/Deny Codes For Area Code:
Table 6: Allow/Deny Codes For Area Code:
Table 7: Allow/Deny Codes For Area Code:
Contd next page
Page 8 

Program 6 - Toll Restriction (contd)
Toll Level: Table 8: Allow/Deny Codes For Area Code:
Table 9: Allow/Deny Codes For Area Code:
Table 10: Allow/Deny Codes For Area Code:
Table 11: Allow/Deny Codes For Area Code:
Contd next page
Page 9 

Program 6 - Toll Restriction (contd)
Toll Level: Table 12: Allow/Deny Codes For Area Code:
Table 13: Allow/Deny Codes For Area Code:
To enter Program 6 data:
1. Enter program mode.
# + dial 775312 + #.
2. Press key 6.
3. For first-time programming or to initialize (reset) toll levels: Dial I + Y. Otherwise, go to step 5.
To stop initialization after dialing I: Dial N + go to step 5.
4. To allow the system to accept the new NPA codes, at the prompt NEW DIAL PLAN-N, dial Y.
5. Dial P to program toll...

Program 6 - Toll Restriction (contd)
9. Select an option:
- To program another level: Go to step 6.
- To exit Program 6: SAVE.
- To enter another program after exiting: Press its key.
- To exit mode: SAVE twice.
To use the 6-Digit Analysis Tables (4 - 13) when you see ADD-DELETE- LIST on the display:
1. Dial A, D, or L. 
OR
    Press # to exit the table (and Program 6).
2. Dial the area code intended for 6-digit analysis.
If you selected Listing in step 1, the system lists the codes now, four at a time....