Netgear Netgar VPN FIrewall FVS336Gv2 Reference Manual

Configure the IPv4 Internet and WAN Settings 
51  ProSAFE Dual WAN Gigabit WAN SSL VPN Firewall FVS336Gv2
7. In the Load Balancing Settings section, configure the following settings:
a.Select the Load Balancing Mode radio button.
b. From the corresponding menu on the right, select a load balancing method:
•Weighted LB. With weighted load balancing, balance weights are calculated 
based on WAN link speed and available WAN bandwidth.
This is the default setting and most efficient load balancing algorithm....

Configure the IPv4 Internet and WAN Settings 
52 ProSAFE Dual WAN Gigabit WAN SSL VPN Firewall FVS336Gv2 
The NETGEAR Configuration Manager Login screen displays.
3. In the Username field, type your user name and in the Password / Passcode field, type 
your password.
For the default administrative account, the default user name is admin and the default 
password is password.
4. If you changed the default domain or were assigned a domain, from the Domain menu, 
select the domain.
If you did not change the...

Configure the IPv4 Internet and WAN Settings 
53  ProSAFE Dual WAN Gigabit WAN SSL VPN Firewall FVS336Gv2
8. Configure the protocol binding settings as described in the following table.
9. Click the Apply button.
SettingDescription 
Service From the menu, select a service or application to be covered by this rule. If the service or 
application does not appear in the list, you must define it (see Manage Customized 
Services on page
 280).
Local Gateway From the menu, select a WAN interface.
Source...

Configure the IPv4 Internet and WAN Settings 
54 ProSAFE Dual WAN Gigabit WAN SSL VPN Firewall FVS336Gv2 
Your settings are saved.
The protocol binding rule is added to the Protocol Binding table. The rule is automatically 
enabled, which is indicated by a green circle in the ! status icon column.
Change a Protocol Binding Rule
The following procedure describes how to change an existing protocol binding rule.
To change a protocol binding rule:
1. On your computer, launch an Internet browser.
2. In the...

Configure the IPv4 Internet and WAN Settings 
55  ProSAFE Dual WAN Gigabit WAN SSL VPN Firewall FVS336Gv2
To enable, disable, or remove one or more protocol binding rules:
1. On your computer, launch an Internet browser.
2. In the address field of your browser, enter the IP address that was assigned to the VPN 
firewall during the installation process.
The VPN firewall factory default IP address is 192.168.1.1.
The NETGEAR Configuration Manager Login screen displays.
3. In the Username field, type your...

Configure the IPv4 Internet and WAN Settings 
56 ProSAFE Dual WAN Gigabit WAN SSL VPN Firewall FVS336Gv2 
Configure the Auto-Rollover Mode and Failure Detection 
Method for IPv4 Interfaces
Instead of using two WAN interfaces simultaneously in a load balancing configuration, you 
can use one WAN interface as the primary link and the other WAN interface as the backup 
link for increased reliability.
The following sections provide information about configuring auto-rollover mode and the 
failure detection...

Configure the IPv4 Internet and WAN Settings 
57  ProSAFE Dual WAN Gigabit WAN SSL VPN Firewall FVS336Gv2
For the default administrative account, the default user name is admin and the default 
password is password.
4. If you changed the default domain or were assigned a domain, from the Domain menu, 
select the domain.
If you did not change the domain or were not assigned a domain, leave the menu 
selection at geardomain.
5. Click the Login button.
The Router Status screen displays.
6. Select Network...

Configure the IPv4 Internet and WAN Settings 
58 ProSAFE Dual WAN Gigabit WAN SSL VPN Firewall FVS336Gv2 
Your settings are saved.
Configure the Failure Detection Method for IPv4 WAN Interfaces
The following procedure describes how to configure the failure detection method for IPv4 
WAN interfaces that function in auto-rollover mode.
To configure the failure detection method for IPv4 WAN interfaces:
1. On your computer, launch an Internet browser.
2. In the address field of your browser, enter the IP...

Configure the IPv4 Internet and WAN Settings 
59  ProSAFE Dual WAN Gigabit WAN SSL VPN Firewall FVS336Gv2
Note:The default time to roll over after the primary WAN interface fails is 
two
 minutes. The minimum test period is 30 seconds, and the 
minimum number of tests is 2.
11. Click the Apply button.
Your settings are saved.
Note:You can configure the VPN firewall to generate a WAN status log and 
email this log to a specified address (see 
Manage Logging, Alerts, 
and Event Notifications on page 567)....

Configure the IPv4 Internet and WAN Settings 
60 ProSAFE Dual WAN Gigabit WAN SSL VPN Firewall FVS336Gv2 
•Remove One or More Secondary WAN Addresses
Secondary IPv4 WAN Addresses
You can set up a single WAN Ethernet port to be accessed through multiple IPv4 addresses 
by adding aliases to the port. An alias is a secondary WAN address. One advantage is, for 
example, that you can assign different virtual IP addresses to a web server and an FTP 
server, even though both servers use the same physical IP...