Netgear Ac1450 802 11ac Dual Band Gigabit Smart Wifi Router User Manual

							Advanced Settings
111  AC1450 Smart WiFi Router
4.(Optional) If your ISP charges for extra data volume when you make a new connection, 
enter the extra data volume in MB in the Round up data volume for each connection by field.
5.In the Traffic Counter section, set the traffic counter to begin at a specific time and date.
If you want the traffic counter to start immediately, click the Restart Counter Now button.
6.In the Traffic Control section, specify whether the router should issue a warning message 
before the monthly limit of Mbytes or hours is reached. 
By default, the value is 0 and no warning message is issued. You can select one of the 
following to occur when the limit is attained:
•The Internet LED flashes green or amber. 
•The Internet connection is disconnected and disabled.
7.Click the Apply button.
The Internet Traffic Statistics section helps you to monitor the data traffic.
Click the Refresh button to update the Traffic Statistics section.
Click the Traffic Status button to display more information about the data traffic on your 
router and to change the poll interval. 
						

							11 2
10
10.   Troubleshooting
This chapter provides information to help you diagnose and solve problems you might have with 
your router. If you do not find the solution here, check the NETGEAR support site at 
http://support.netgear.com for product and contact information.
This chapter contains the following sections:
•Quick Tips 
•Troubleshoot with the LEDs 
•Cannot Log In to the Router 
•Cannot Access the Internet 
•Changes Not Saved 
•Wireless Connectivity 
•Troubleshoot Your Network Using the Ping Utility  
						

							Troubleshooting
11 3  AC1450 Smart WiFi Router
Quick Tips
This section describes tips for troubleshooting some common problems.
Sequence to Restart Your Network
When you need to restart your network, follow this sequence:
1.Turn off and unplug the modem. 
2.Turn off the router.
3.Plug in the modem and turn it on. Wait 2 minutes.
4.Turn on the router and wait 2 minutes.
Check Ethernet Cable Connections
If your device does not power on, make sure that the Ethernet cables are securely plugged 
in. 
•The Internet LED on the router is on if the Ethernet cable connecting the router and the 
modem is plugged in securely and the modem and router are turned on. 
•For each powered-on computer connected to the router by an Ethernet cable, the 
corresponding numbered router LAN port LED is on. 
Wireless Settings
Make sure that the wireless settings in the computer and router match exactly. 
•For a wirelessly connected computer, the wireless network name (SSID) and wireless 
security settings of the router and wireless computer need to match exactly. 
•If you set up an access list in the Advanced Wireless Settings screen, you have to add 
each wireless computer’s MAC address to the router’s access list.
Network Settings
Make sure that the network settings of the computer are correct. 
•Wired and wirelessly connected computers need to have network (IP) addresses on the 
same network as the router. The simplest way to do this is to configure each computer to 
obtain an IP address automatically using DHCP. 
•Some cable modem service providers require you to use the MAC address of the 
computer initially registered on the account. You can view the MAC address in the 
Attached Devices screen. 
						

							Troubleshooting11 4
AC1450 Smart WiFi Router 
Troubleshoot with the LEDs
After you turn on power to the router, the following sequence of events \
should occur:
1. When power is first applied, verify that the Power/T
 est LED  is lit.
2. V
erify that the Power/Test LED turns amber within a few seconds, indicating that the self-test \
is running.
3. After approximately 30 seconds, verify the following:
• The Power LED is lit solid green.
• The Internet LED is lit.
• The Wireless LED is lit unless you turned of
 f the wireless radio.
The LEDs on the front panel of the router can be used for troubleshootin\
g.
Power LED Is Off or Blinking
• Make sure that the power cord is securely connected to your router and t\
hat the power 
adapter is securely connected to a functioning power outlet. 
• Check that you are using the 12V DC, 2.5A power adapter that NETGEAR sup\
plied for 
this product.
• If the Power LED blinks slowly and continuously
 , the router firmware is corrupted. This 
can happen if a firmware upgrade is interrupted, or if the router detect\
s a problem with the 
firmware. If the error persists, you have a hardware problem. For recove\
ry instructions, or 
help with a hardware problem, contact technical support at www.netgear.com/support.
Power LED Stays Amber
When the router is turned on, the Power LED turns amber for about 20 sec\
onds and then 
turns green. If the LED does not turn green, the router has a problem.
If the Power LED is still amber 1 minute after you turn on power to the \
router:
1. T
urn off the power and then turn it back on to see if the router recovers.
2. Press and hold the  Reset button.
The router returns to its factory settings and restarts. 
See Troubleshoot Your Network Using the Ping Utility  on page
  120.
If the error persists, you might have a hardware problem. Contact techni\
cal support at 
www.netgear.com/support. 
						

							Troubleshooting
11 5  AC1450 Smart WiFi Router
LEDs Never Turn Off
When the router is turned on, the LEDs turn on for about 10 seconds and then turn off. If all 
the LEDs stay on, this indicates a fault within the router.
If all LEDs are still on 1 minute after power-up:
•Cycle the power to see if the router recovers.
•Press and hold the Reset button.
The router returns to its factory settings and restarts. For more information, see 
Troubleshoot Your Network Using the Ping Utility on page 120.
If the error persists, you might have a hardware problem. Contact technical support at 
www.netgear.com/support.
Internet or Ethernet Port LEDs Are Off
If either the Ethernet port LEDs or the Internet LED does not light when the Ethernet 
connection is made, check the following:
•Make sure that the Ethernet cable connections are secure at the router and at the modem 
or computer.
•Make sure that power is turned on to the connected modem or computer.
•Be sure that you are using the correct cable.
When connecting the router’s Internet port to a cable or DSL modem, use the cable that 
was supplied with the cable or DSL modem. This cable could be a standard 
straight-through Ethernet cable or an Ethernet crossover cable.
Wireless LEDs Are Off
If the Wireless LEDs stay off, check to see if the WFi On/Off button on the router has been 
pressed. This button turns the wireless radios in the router on and off. The Wireless LEDs are 
lit when the wireless radio is turned on.
The Push N Connect (WPS) Button Blinks Amber
If you use the WPS function, and the WPS LED blinks amber, check the following:
•Make sure that you are using the button and not the router’s built-in registrar.
•Check that PIN verification has succeeded for the wireless device you are adding to the 
wireless network.
•Make sure that you have not pressed the WPS button on the side of the router after 
disabling the WPS feature (you logged in to the router and disabled this previously).
•Check that the router is not in the temporary AP setup locked state (if you are using the 
wireless repeater function). 
						

							Troubleshooting
11 6 AC1450 Smart WiFi Router 
Cannot Log In to the Router
If you are unable to log in to the router from a computer on your local network, check the 
following:
•If you are using an Ethernet-connected computer, check the Ethernet connection 
between the computer and the router.
•Make sure that the IP address of your computer is on the same subnet as the router. If 
you are using the recommended addressing scheme, your computer’s address should be 
in the range of 192.168.1.2 to 192.168.1.254. 
•If your computer’s IP address is shown as 169.254.x.x, recent versions of Windows and 
Mac OS generate and assign an IP address if the computer cannot reach a DHCP server. 
These autogenerated addresses are in the range of 169.254.x.x. If your IP address is in 
this range, check the connection from the computer to the router, and reboot your 
computer.
•If your router’s IP address was changed and you do not know the current IP address, 
clear the router’s configuration to factory defaults. This sets the router’s IP address to 
192.168.1.1. For more information, see 
Factory Settings on page 123.
•Make sure that your browser has Java, JavaScript, or ActiveX enabled. If you are using 
Internet Explorer, click Refresh to be sure that the Java applet is loaded.
•Try quitting the browser and launching it again.
•Make sure that you are using the correct login information. The factory default login name 
is admin, and the password is password. Make sure that Caps Lock is off when you 
enter this information.
•If you are attempting to set up your NETGEAR router as an additional router behind an 
existing router in your network, consider replacing the existing router. NETGEAR does 
not support such a configuration.
•If you are attempting to set up your NETGEAR router as a replacement for an ADSL 
gateway in your network, the router cannot perform many gateway services. For 
example, the router cannot convert ADSL or cable data into Ethernet networking 
information. NETGEAR does not support such a configuration.
Cannot Access the Internet
If you can access your router but not the Internet, check to see if the router can obtain an IP 
address from your Internet service provider (ISP). Unless your ISP provides a fixed IP 
address, your router requests an IP address from the ISP. You can determine whether the 
request was successful using the Router Status screen.
To check the WAN IP address: 
1.Start your browser, and select an external site such as www.netgear.com.
2.Access the router interface at www.routerlogin.net.
3.Select Administration > Router Status. 
						

							Troubleshooting
11 7  AC1450 Smart WiFi Router
4.Check that an IP address is shown for the Internet port. If 0.0.0.0 is shown, your router has 
not obtained an IP address from your ISP.
If your router cannot obtain an IP address from the ISP, you might need to force your cable or 
DSL modem to recognize your new router by restarting your network. For more information, 
see 
Sequence to Restart Your Network on page 11 3.
If your router is still unable to obtain an IP address from the ISP, the problem might be one of 
the following:
•Your Internet service provider (ISP) might require a login program. 
Ask your ISP whether they require PPP over Ethernet (PPPoE) or some other type of 
login.
•If your ISP requires a login, the login name and password might be set incorrectly.
•Your ISP might check for your computer’s host name. 
Assign the computer host name of your ISP account as the account name in the Internet 
Setup screen.
•Your ISP allows only one Ethernet MAC address to connect to Internet and might check 
for your computer’s MAC address. In this case, do one of the following:
-Inform your ISP that you have bought a new network device, and ask them to use the 
router’s MAC address.
-Configure your router to clone your computer’s MAC address.
If your router can obtain an IP address, but your computer is unable to load any web pages 
from the Internet:
•Your computer might not recognize any DNS server addresses. 
A DNS server is a host on the Internet that translates Internet names (such as www 
addresses) to numeric IP addresses. Typically, your ISP provides the addresses of one or 
two DNS servers for your use. If you entered a DNS address during the router’s 
configuration, reboot your computer, and verify the DNS address. You can configure your 
computer manually with DNS addresses, as explained in your operating system 
documentation.
•Your computer might not have the router configured as its TCP/IP gateway.
If your computer obtains its information from the router by DHCP, reboot the computer, 
and verify the gateway address.
•You might be running login software that is no longer needed.
If your ISP provided a program to log you in to the Internet (such as WinPoET), you no 
longer need to run that software after installing your router. You might need to go to 
Internet Explorer and select Tools > Internet Options, click the Connections tab, and 
select Never dial a connection. 
						

							Troubleshooting
11 8 AC1450 Smart WiFi Router 
Troubleshoot PPPoE
If you are using PPPoE, try troubleshooting your Internet connection.
To troubleshoot a PPPoE connection:
1.Select Administration > Router Status.
2.Click Connection Status. 
3.Check to see if your PPPoE connection is up and working.
4.If any of the field s on the Connection Status screen indicate Failed, you can attempt to 
reconnect by clicking Connect. The router continues to attempt to connect indefinitely.
5.If you cannot connect after several minutes, you might be using an incorrect service name, 
user name, or password. There might also be a provisioning problem with your ISP.
Note:Unless you connect manually, the router does not authenticate using 
PPPoE until data is transmitted to the network.
Troubleshoot Internet Browsing
If your router can obtain an IP address but your computer is unable to load any web pages 
from the Internet, check the following:
•Your computer might not recognize any DNS server addresses. A DNS server is a host 
on the Internet that translates Internet names (such as www addresses) to numeric IP 
addresses.
Typically, your ISP provides the addresses of one or two DNS servers for your use. If you 
entered a DNS address during the router’s configuration, restart your computer.
Alternatively, you can configure your computer manually with a DNS address, as 
explained in the documentation for your computer.
•Your computer might not have the router configured as its default gateway.
Reboot the computer and verify that the router address (www.routerlogin.net) is listed by 
your computer as the default gateway address.
•You might be running log in software that is no longer needed. If your ISP provided a 
program to log you in to the Internet (such as WinPoET), you no longer need to run that 
software after installing your router. You might need to go to Internet Explorer and select 
Tools > Internet Options, click the Connections tab, and select Never dial a 
connection. 
						

							Troubleshooting
11 9  AC1450 Smart WiFi Router
Changes Not Saved
If the router does not save the changes you make in the router interface, check the following:
•When entering configuration settings, always click the Apply button before moving to 
another screen or tab, or your changes are lost. 
•Click the Refresh or Reload button in the web browser. The changes might have 
occurred, but the old settings might be in the web browser’s cache.
Wireless Connectivity
If you are having trouble connecting wirelessly to the router, try to isolate the problem. 
•Does the wireless device or computer that you are using find your wireless network?
If not, check the WiFi LED on the front of the router. If it is off, you can press the WiFi 
On/Off button on the side of the router to turn the router wireless radios back on.
If you disabled the router’s SSID broadcast, then your wireless network is hidden and 
does not show up in your wireless client’s scanning list. (By default, SSID broadcast is 
enabled.)
•Does your wireless device support the security that you are using for your wireless 
network (WPA or WPA2)?
•If you want to view the wireless settings for the router, use an Ethernet cable to connect a 
computer to a LAN port on the router. Then log in to the router, and select Wireless see 
(
Basic Wireless Settings on page 24). 
Note: Be sure to click Apply if you change settings.
Wireless Signal Strength
If your wireless device finds your network, but the signal strength is weak, check these 
conditions:
•Is your router too far from your computer, or too close? Place your computer near the 
router, but at least 6 feet (1.8 meters) away, and see whether the signal strength 
improves.
•Are objects between the router and your computer blocking the wireless signal? 
						

							Troubleshooting
120 AC1450 Smart WiFi Router 
Troubleshoot Your Network Using the Ping Utility
Most network devices and routers contain a ping utility that sends an echo request packet to 
the designated device. The device then responds with an echo reply. You can easily 
troubleshoot a network is easy using the ping utility in your computer or workstation. 
Test the LAN Path to Your Router
You can ping the router from your computer to verify that the LAN path to your router is set up 
correctly.
To ping the router from a Windows computer:
1.From the Windows toolbar, click Start and select Run.
2.In the field provided, type ping followed by the IP address of the router, as in this example:
ping www.routerlogin.net
3.Click OK.
You should see a message like this one:
Pinging  with 32 bytes of data
If the path is working, you see this message:
Reply from < IP address >: bytes=32 time=NN ms TTL=xxx
If the path is not working, you see this message:
Request timed out
If the path is not functioning correctly, you could have one of the following problems:
•Wrong physical connections
For a wired connection, make sure that the numbered LAN port LED is lit for the port to 
which you are connected.
Check that the appropriate LEDs are on for your network devices. If your router and 
computer are connected to a separate Ethernet switch, make sure that the link LEDs are 
lit for the switch ports that are connected to your computer and router.
•Wrong network configuration
Verify that the Ethernet card driver software and TCP/IP software are both installed and 
configured on your computer. 
Verify that the IP address for your router and your computer are correct and that the 
addresses are on the same subnet.