NEC Vt700 Projector User Manual
Here you can view all the pages of manual NEC Vt700 Projector User Manual. The NEC manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 31
23 Correcting Keystone Distortion Correcting Keystone Distortion If the screen is tilted vertically, keystone distortion becomes large. Proceed with the following steps to correct keystone distortion NOTE: The Keystone correction can cause an image to be slightly blurred because the correction is made electronically. NOTE: The Keystone correction range can be made narrower, depending on a signal or its aspect ratio selection. Adjusting with buttons on the cabinet 1. Press the SELECT or button with...
Page 32
![Page 32
24
Adjusting with the Auto Keystone Function
The Auto Keystone correction feature will correct the vertical distortion of\
a projected image on the screen. No special
operation required. Just put the projector on a flat surface.
TIP: Even when the menu setting for [Auto Keystone] is turned on, [Keyst\
one] can be adjusted manually.
To turn on [Auto Keystone], proceed the following steps.
1. Press the MENU button
The menu will be displayed.
2. Press the SELECT button to select [Setup] and press the...](http://img.usermanuals.tech/thumb/54/92465/w300_nec-vt700-manual_d-31.png "Page 32
24
Adjusting with the Auto Keystone Function
The Auto Keystone correction feature will correct the vertical distortion of\
a projected image on the screen. No special
operation required. Just put the projector on a flat surface.
TIP: Even when the menu setting for [Auto Keystone] is turned on, [Keyst\
one] can be adjusted manually.
To turn on [Auto Keystone], proceed the following steps.
1. Press the MENU button
The menu will be displayed.
2. Press the SELECT button to select [Setup] and press the...")
24 Adjusting with the Auto Keystone Function The Auto Keystone correction feature will correct the vertical distortion of\ a projected image on the screen. No special operation required. Just put the projector on a flat surface. TIP: Even when the menu setting for [Auto Keystone] is turned on, [Keyst\ one] can be adjusted manually. To turn on [Auto Keystone], proceed the following steps. 1. Press the MENU button The menu will be displayed. 2. Press the SELECT button to select [Setup] and press the...
Page 33
![Page 33
25
3. Projecting an Image (Basic Operation)
Optimizing RGB Picture Automatically
Adjusting the Image Using Auto Adjust
Optimizing an RGB image automatically.
Press the AUTO ADJ. button to optimize an RGB image automatically.
This adjustment may be necessary when you connect your computer for the \
first time.
[Poor picture]
[Normal picture]
VOLUMEL-CLICK
MOUSER-CLICK
ASPECT HELP FREEZE
PICTURE
AUTO ADJ.S-VIDEO VIDEOCOMPUTER
LAMP MODE12
Increase volume
Decrease volumeVOLUMEL-CLICK
MOUSER-CLICK
ASPECT...](http://img.usermanuals.tech/thumb/54/92465/w300_nec-vt700-manual_d-32.png "Page 33
25
3. Projecting an Image (Basic Operation)
Optimizing RGB Picture Automatically
Adjusting the Image Using Auto Adjust
Optimizing an RGB image automatically.
Press the AUTO ADJ. button to optimize an RGB image automatically.
This adjustment may be necessary when you connect your computer for the \
first time.
[Poor picture]
[Normal picture]
VOLUMEL-CLICK
MOUSER-CLICK
ASPECT HELP FREEZE
PICTURE
AUTO ADJ.S-VIDEO VIDEOCOMPUTER
LAMP MODE12
Increase volume
Decrease volumeVOLUMEL-CLICK
MOUSER-CLICK
ASPECT...")
25 3. Projecting an Image (Basic Operation) Optimizing RGB Picture Automatically Adjusting the Image Using Auto Adjust Optimizing an RGB image automatically. Press the AUTO ADJ. button to optimize an RGB image automatically. This adjustment may be necessary when you connect your computer for the \ first time. [Poor picture] [Normal picture] VOLUMEL-CLICK MOUSER-CLICK ASPECT HELP FREEZE PICTURE AUTO ADJ.S-VIDEO VIDEOCOMPUTER LAMP MODE12 Increase volume Decrease volumeVOLUMEL-CLICK MOUSER-CLICK ASPECT...
Page 34
![Page 34
26
Turning off the Projector
To turn off the projector:
3. Projecting an Image (Basic Operation)
SELECT
MENU
ENTEREXITLAMP
STATUS
POWER
ON/STAND BY
AUTO ADJ.
SOURCEENTEREXIT
MENU
UP
MAGNIFY PAGE OFF
POWER ON
PIC-MUTE
DOWN
1. First, press the POWER (ON/STAND BY) button on the projector cabinet or the POWER OFF button on
the remote control. The [Power Off / Are you sure?]message will appear.
2. Secondly, press the ENTER button or press the POWER (ON/STAND BY) or the POWER OFF buttonagain.
The power...](http://img.usermanuals.tech/thumb/54/92465/w300_nec-vt700-manual_d-33.png "Page 34
26
Turning off the Projector
To turn off the projector:
3. Projecting an Image (Basic Operation)
SELECT
MENU
ENTEREXITLAMP
STATUS
POWER
ON/STAND BY
AUTO ADJ.
SOURCEENTEREXIT
MENU
UP
MAGNIFY PAGE OFF
POWER ON
PIC-MUTE
DOWN
1. First, press the POWER (ON/STAND BY) button on the projector cabinet or the POWER OFF button on
the remote control. The [Power Off / Are you sure?]message will appear.
2. Secondly, press the ENTER button or press the POWER (ON/STAND BY) or the POWER OFF buttonagain.
The power...")
26 Turning off the Projector To turn off the projector: 3. Projecting an Image (Basic Operation) SELECT MENU ENTEREXITLAMP STATUS POWER ON/STAND BY AUTO ADJ. SOURCEENTEREXIT MENU UP MAGNIFY PAGE OFF POWER ON PIC-MUTE DOWN 1. First, press the POWER (ON/STAND BY) button on the projector cabinet or the POWER OFF button on the remote control. The [Power Off / Are you sure?]message will appear. 2. Secondly, press the ENTER button or press the POWER (ON/STAND BY) or the POWER OFF buttonagain. The power...
Page 35
![Page 35
27
\b After Use
Preparation: Make sure that the projector is turned off.
1. Unplug the power cable.
2. Disconnect any other cables.
3. Retract adjustable tilt foot if extended.4. Cover the lens with the lens cap.5. Put the projector and accessories in the supplied soft case. Place the projector in the soft case with the lens facing upward as show\
n below. This is to prevent the lens fromdamage.
3. Projecting an Image (Basic Operation)
NOTE: When placing the projector in the soft case, retract the tilt...](http://img.usermanuals.tech/thumb/54/92465/w300_nec-vt700-manual_d-34.png "Page 35
27
\b After Use
Preparation: Make sure that the projector is turned off.
1. Unplug the power cable.
2. Disconnect any other cables.
3. Retract adjustable tilt foot if extended.4. Cover the lens with the lens cap.5. Put the projector and accessories in the supplied soft case. Place the projector in the soft case with the lens facing upward as show\
n below. This is to prevent the lens fromdamage.
3. Projecting an Image (Basic Operation)
NOTE: When placing the projector in the soft case, retract the tilt...")
27 \b After Use Preparation: Make sure that the projector is turned off. 1. Unplug the power cable. 2. Disconnect any other cables. 3. Retract adjustable tilt foot if extended.4. Cover the lens with the lens cap.5. Put the projector and accessories in the supplied soft case. Place the projector in the soft case with the lens facing upward as show\ n below. This is to prevent the lens fromdamage. 3. Projecting an Image (Basic Operation) NOTE: When placing the projector in the soft case, retract the tilt...
Page 36
![Page 36
28
Turning off the Image and Sound
Press the PIC-MUTE button to turn off the image and sound for a short
period of time. Press again to restore the image and sound.
NOTE:
Sound from the AUDIO OUT jack (Stereo mini) can be turned off.
Freezing a Picture
Press the FREEZE button to freeze a picture. Press again to resume
motion.
Enlarging a Picture
You can enlarge the picture up to four times.
NOTE: The maximum magnification may be less than four times depending on\
the signal.
To do so:
1. Press...](http://img.usermanuals.tech/thumb/54/92465/w300_nec-vt700-manual_d-35.png "Page 36
28
Turning off the Image and Sound
Press the PIC-MUTE button to turn off the image and sound for a short
period of time. Press again to restore the image and sound.
NOTE:
Sound from the AUDIO OUT jack (Stereo mini) can be turned off.
Freezing a Picture
Press the FREEZE button to freeze a picture. Press again to resume
motion.
Enlarging a Picture
You can enlarge the picture up to four times.
NOTE: The maximum magnification may be less than four times depending on\
the signal.
To do so:
1. Press...")
28 Turning off the Image and Sound Press the PIC-MUTE button to turn off the image and sound for a short period of time. Press again to restore the image and sound. NOTE: Sound from the AUDIO OUT jack (Stereo mini) can be turned off. Freezing a Picture Press the FREEZE button to freeze a picture. Press again to resume motion. Enlarging a Picture You can enlarge the picture up to four times. NOTE: The maximum magnification may be less than four times depending on\ the signal. To do so: 1. Press...
Page 37
![Page 37
29
Changing Lamp Mode
This feature enables you to select two brightness modes of the lamp:
Normal and Eco modes. The lamp life can be extended by using the Eco mode.
To change to the [Eco] mode, do the following:
1. Press the LAMP MODE button on the remote control to display [Lamp Mode] \
screen.
2. Use the SELECT
or button to select [Eco] mode.
3. Press the ENTER button.
To change from [Eco] to [Normal], Go back to Step 2 and select [Normal]. R\
epeat Step 3.
NOTE:
• The Lamp Mode can be...](http://img.usermanuals.tech/thumb/54/92465/w300_nec-vt700-manual_d-36.png "Page 37
29
Changing Lamp Mode
This feature enables you to select two brightness modes of the lamp:
Normal and Eco modes. The lamp life can be extended by using the Eco mode.
To change to the [Eco] mode, do the following:
1. Press the LAMP MODE button on the remote control to display [Lamp Mode] \
screen.
2. Use the SELECT
or button to select [Eco] mode.
3. Press the ENTER button.
To change from [Eco] to [Normal], Go back to Step 2 and select [Normal]. R\
epeat Step 3.
NOTE:
• The Lamp Mode can be...")
29 Changing Lamp Mode This feature enables you to select two brightness modes of the lamp: Normal and Eco modes. The lamp life can be extended by using the Eco mode. To change to the [Eco] mode, do the following: 1. Press the LAMP MODE button on the remote control to display [Lamp Mode] \ screen. 2. Use the SELECT or button to select [Eco] mode. 3. Press the ENTER button. To change from [Eco] to [Normal], Go back to Step 2 and select [Normal]. R\ epeat Step 3. NOTE: • The Lamp Mode can be...
Page 38
![Page 38
30
4. Convenient Features
5. Use the SELECT or button to select [On] and press the ENTER button.
The [Security Keyword] screen will be displayed.
6. Type in a combination of the four SELECT buttons and press the ENTER button.
NOTE: A keyword must be 4 to 10 digits in length. Please make a note of\
your keyword.
The [Confirm Keyword] screen will be displayed.
NOTE:Do not forget your keyword. However, if you forget your keyword, NEC or your dealer will provide you with your Release
Code upon...](http://img.usermanuals.tech/thumb/54/92465/w300_nec-vt700-manual_d-37.png "Page 38
30
4. Convenient Features
5. Use the SELECT or button to select [On] and press the ENTER button.
The [Security Keyword] screen will be displayed.
6. Type in a combination of the four SELECT buttons and press the ENTER button.
NOTE: A keyword must be 4 to 10 digits in length. Please make a note of\
your keyword.
The [Confirm Keyword] screen will be displayed.
NOTE:Do not forget your keyword. However, if you forget your keyword, NEC or your dealer will provide you with your Release
Code upon...")
30 4. Convenient Features 5. Use the SELECT or button to select [On] and press the ENTER button. The [Security Keyword] screen will be displayed. 6. Type in a combination of the four SELECT buttons and press the ENTER button. NOTE: A keyword must be 4 to 10 digits in length. Please make a note of\ your keyword. The [Confirm Keyword] screen will be displayed. NOTE:Do not forget your keyword. However, if you forget your keyword, NEC or your dealer will provide you with your Release Code upon...
Page 39
![Page 39
31
4. Convenient Features
To turn on the projector when Security is enabled:
1. Press the Main Power Switch to the On position (I).
2. Press and hold the POWER ON or the ON/STAND BY button for a minimum of 1 second.
The projector will be turned on and display a message to the effect that the projector is security-protected.
3. Press the MENU button.
The Security Keyword screen will be displayed.
4. Enter your keyword in the Security Keyword screen and press the ENTER bu\
tton.
Y ou can view the...](http://img.usermanuals.tech/thumb/54/92465/w300_nec-vt700-manual_d-38.png "Page 39
31
4. Convenient Features
To turn on the projector when Security is enabled:
1. Press the Main Power Switch to the On position (I).
2. Press and hold the POWER ON or the ON/STAND BY button for a minimum of 1 second.
The projector will be turned on and display a message to the effect that the projector is security-protected.
3. Press the MENU button.
The Security Keyword screen will be displayed.
4. Enter your keyword in the Security Keyword screen and press the ENTER bu\
tton.
Y ou can view the...")
31 4. Convenient Features To turn on the projector when Security is enabled: 1. Press the Main Power Switch to the On position (I). 2. Press and hold the POWER ON or the ON/STAND BY button for a minimum of 1 second. The projector will be turned on and display a message to the effect that the projector is security-protected. 3. Press the MENU button. The Security Keyword screen will be displayed. 4. Enter your keyword in the Security Keyword screen and press the ENTER bu\ tton. Y ou can view the...
Page 40
![Page 40
32
4. Convenient Features
Using the Optional Remote Mouse Receiver (NP01MR)
The optional remote mouse receiver enables you to operate your computer’s mouse functions from the remote control.
It is a great convenience for clicking through your computer-generated p\
resentations.
Connecting the remote mouse receiver to your computer
If you wish to use the remote mouse function, connect the mouse receiver\
and computer.
The mouse receiver can be connected directly to the computer’s USB port (type A)....](http://img.usermanuals.tech/thumb/54/92465/w300_nec-vt700-manual_d-39.png "Page 40
32
4. Convenient Features
Using the Optional Remote Mouse Receiver (NP01MR)
The optional remote mouse receiver enables you to operate your computer’s mouse functions from the remote control.
It is a great convenience for clicking through your computer-generated p\
resentations.
Connecting the remote mouse receiver to your computer
If you wish to use the remote mouse function, connect the mouse receiver\
and computer.
The mouse receiver can be connected directly to the computer’s USB port (type A)....")
32 4. Convenient Features Using the Optional Remote Mouse Receiver (NP01MR) The optional remote mouse receiver enables you to operate your computer’s mouse functions from the remote control. It is a great convenience for clicking through your computer-generated p\ resentations. Connecting the remote mouse receiver to your computer If you wish to use the remote mouse function, connect the mouse receiver\ and computer. The mouse receiver can be connected directly to the computer’s USB port (type A)....