NEC Vt700 Projector User Manual

3
MEN USELE C TLA M P
S TA TU S
P O W ERO N/STAND  BYSO UR
CEA
UTO  A DJ.
EN TEREXIT
FO CU SZO OM
1. Introduction
  Part Names of the Projector
Front/Top
FO C
US
M EN USELE C T
L A M P
S TA TU S
P O W ERO N/S TA ND B Y S
O URCE A
UTO  A DJ.EN TEREXI
T
Z O OM
Zoom Lever (→ page  22)Controls
(→ page  5)
Lens
Lens Cap
Built-in Security Slot (  )*
Focus Ring
(→ page  22)
Remote sensor
(→ page  8) V
entilation (inlet) / Filter Cover
(→ page  48)
T wo filters
AC Input
Connect the supplied power cables...

4
1. Introduction
Adjustable Tilt Foot(→ page  21)
Rear Foot (Left / Right)
(→ page  21)
Adjustable Tilt Foot Button (
→ page  21) Lamp Cover
(→ page  50)
Carrying handle Screw
Phillips-head screwdriver
(not supplied)
Attaching the supplied carrying handle
Y ou can carry the projector by attaching the supplied carrying handle sec\
urely to the projector.
To  attach the supplied carrying handle, use a Phillips-head screwdriver an\
d the supplied two screws.
Place a soft cloth on the working surface...

5
1. Introduction
T op Features
SELECT
MENU
ENTEREXITLAMP
STATUS
POWER
ON/STAND BY
AUTO ADJ.
SOURCE
4 7
83 1
29
10
56
1. LAMP Indicator 
(→ page  50,53 )
2. STATUS Indicator  (→ page  53)
3. POWER Indicator  (→ page  18,26 ,53 )
4. POWER Button (ON / STAND BY) (
)
( → page  18,26 )
5. SOURCE Button  (→ page  20)
6. AUTO ADJ. Button  (→ page  25)
7. MENU Button  (→ page  34)
8. SELECT  
 / Volume Buttons   / Key-
stone Buttons  
 ( → page  23,25 )
9. ENTER Button
10. EXIT Button 

6
1. Introduction
T erminal Panel Features
AUDIO OUT
AUDIO IN
MONITOR OUT (COMP 1)
COMPUTER 1 INCOMPUTER 2 (DVI-I) IN
AUDIO IN
S-VIDEO
IN
VIDEO IN PC CTRL
L
R
19852
3476
1. COMPUTER 1 IN/ Component Input Connector
(Mini D-Sub 15 Pin)  (→ page  11,13 )
2. AUDIO IN Mini Jack (Stereo Mini)  (→ page  11,12 ,15 )
3. AUDIO OUT Mini Jack (Stereo Mini)  (→ page  14)
4. MONITOR OUT Connector (Mini D-Sub 15 Pin) (→ page  14)
5. S-VIDEO IN Connector (Mini DIN 4 Pin) (→ page  16)
6. VIDEO IN Connector (RCA)  (→...

7
1. Introduction
 Part Names of the Remote Control
1. Infrared Transmitter
(→  page  8)
2. POWER ON Button (→  page  18)
3. POWER OFF Button (→  page  26)
4. MAGNIFY (+)(–) Button (→  page  28)
5. PIC-MUTE Button (→  page  28)
6. PAGE UP/DOWN Button* (→  page  32,33 )
7. MENU Button (→  page  34)
8. SELECT  
 Button
9. ENTER Button
10. EXIT Button
11 .MOUSE L-CLICK Button*
(→  page  32,33 )
VOLUMEL-CLICK
ENTEREXIT
MENU
UP
MAGNIFY PAGE OFF
POWER ON
PIC-MUTE
DOWN
MOUSE R-CLICK
COMPUTER
ASPECT HELP...

8
1. Introduction
Remote Control Precautions
•Handle the remote control carefully.
• If the remote control gets wet, wipe it dry immediately.
•A void excessive heat and humidity.
• Do not heat, take apart, or throw batteries into fire.
• If you will not be using the remote control for a long time, remove the \
batteries.
• Ensure that you have the batteries’ polarity (+/-) aligned correctly.
• Do not use new and old batteries together, or use different types of batteries together.
• Dispose of used...

9
2. Installation and Connections
FO CUSM E
N US
ELE C T
L A M P
S TA TU S
P O W ERO N
/S T
A N
D B Y S
O UR
CE A
U TO  A DJ.E N TE REX ITZO OM
This section describes how to set up your projector and how to connect v\
ideo and audio sources.
Y
our projector is simple to set up and use. But before you get started, y\
ou must first:
1Set up a screen and the projector.
2 Connect your computer or video equipment
to the projector.
(→  page  11,12 ,13 ,14 ,15 ,16 )
3 Connect the supplied power cable.
(→  page...

10
2. Installation and Connections
Screen bottom
Projector bottom
C
α B
D
Lens centerScreen center
Throw Distance and Screen Size
The following shows the proper relative positions of the projector and s\
creen. Refer to the table to determine the
position of installation.
Distance Chart
B 
=V ertical distance between lens center and
screen center
C = Throw distance
D  =V ertical distance between lens center and
screen bottom (top of screen for ceiling
application)
α  = Throw angle
NOTE: Distances may...

11
2. Installation and Connections
 Making Connections
NOTE: When using with a notebook PC, be sure to connect the projector an\
d notebook PC while the projector is in standby mode
and before turning on the power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on un\
less connected to the projector before being poweredup.* If the screen goes blank while using your remote control, it may be the \
result of the computers screen-saver or power
management software....

12
2. Installation and Connections
When Viewing a DVI Digital Signal
To  project a DVI digital signal, be sure to connect the PC and the projecto\
r using a DVI cable (not supplied) before
turning on your PC or projector. Turn on the projector first and select Computer 2 (Digital) from the so\
urce menu
before turning on your PC.
Failure to do so may not activate the digital output of the graphics car\
d resulting in no picture being displayed. Should
this happen, restart your PC.
Do not disconnect the...