NEC Vt700 Projector User Manual

13
AUDIO OUT
AUDIO IN
MONITOR OUT (COMP 1)
COMPUTER 1 INCOMPUTER 2 (DVI-I) IN
AUDIO IN
S-VIDEOIN
VIDEO IN PC CTRL
L
R
COMPUTER 1 INCOMPUTER 2 (DVI-I) IN
VGA signal cable
(supplied)
IBM PC or Compatibles (Notebook type) or Macintosh (Notebook type)
IBM PC or Compatibles (Desktoptype) or Macintosh (Desktop type)
VGA signal cable (notsupplied)
DVI to VGA adapter(supplied)
2. Installation and Connections
NOTE: When the DVI to VGA adapter is not to be used for an extended peri\
od of time, remove it from the...

14
2. Installation and Connections
Connecting an External Monitor
Y ou can connect a separate, external monitor to your projector to simulta\
neously view on a monitor the RGB analog
image youre projecting.
NOTE:
• Daisy chain connection is not possible.
• The signal from the COMPUTER 2 IN connector cannot be output from the MONITOR OUT connector.
•When the DVI Digital signal is selected, no signals will be output from the MONITOR OUT connector.
AUDIO
IN
AUDIO OUT
AUDIO IN
MONITOR OUT (COMP 1)
COMPUTER...

15
2. Installation and Connections
Connecting Your DVD Player with Component Output
A component signal will be automatically displayed. If not, from the men\
u, select [Setup]  → [Options]  → [Signal
Select]  → [Computer 1], and then place a check mark in the Component radio button\
.
NOTE: Refer to your DVD players owners manual for more information abo\
ut your DVD players video output requirements.
AUDIO INLR
AUDIO OUT
LR
Component
YCbCr
AUDIO OUT
AUDIO IN
MONITOR OUT (COMP 1)
COMPUTER 1 INCOMPUTER 2...

16
2. Installation and Connections
Connecting Your VCR or Laser Disc Player
NOTE: The AUDIO IN L/MONO and R jacks (RCA) are shared between the Vid\
eo and S-Video inputs.
NOTE: Refer to your VCR or laser disc player owners manual for more inf\
ormation about your equipments video output
requirements.
NOTE: An image may not be displayed correctly when a Video or S-Video so\
urce is played back in fast-forward or fast-rewind via
a scan converter.
AUDIO INLRAUDIO OUTLRVIDEO OUTS-VIDEO VIDEO
AUDIO OUT
AUDIO...

17
2. Installation and Connections
Connecting the Supplied Power Cable
Connect the supplied power cable to the projector.
First connect the supplied power cables two-pin plug to the AC IN of the projector, and then connect the other plug of
the supplied power cable in the wall outlet.
CAUTION:
Do not try to touch the ventilation outlet on the left front (when seen\
 from the front) as it can become heated while
the projector is turned on and immediately after the projector is turned\
 off.
CAUTION:
Do...

18
3. Projecting an Image (Basic Operation)
FO CUS
ME
NUSELE C T
L AM P
S TA TU S
P O W ERON/ STA ND BY SOU
RCE AU
TO A DJ .EN TEREXI
T
STATUSLAMP POWER
SELECT
MENU
ENTEREXITLAMP
STATUS
POWER
ON/STAND BY
AUTO ADJ.
SOURCE
MENU UP
MAGNIFY PAGE OFF
POWER ON
PIC-MUTEDOWN
POWERPOWER POWER
STATUS
LAMP STATUSLAMP
STATUSLAMP
Standby Blinking Power On
Steady orange light Blinking  green lightSteady green
light
(→  page  53)
This section describes how to turn on the projector and to project a pic\
ture onto the...

19
3. Projecting an Image (Basic Operation)
Note on Startup screen (Menu Language Select screen)
When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select one
of the 8 menu languages.
To  select a menu language, follow these steps:
1. Use the SELECT 
 or  button to select one of the 8
languages from the menu.
2. Press the ENTER button to execute the selection.
After this has been done, you can proceed to the menu op-
eration.
If you want, you can...

20
3. Projecting an Image (Basic Operation)
SELECT
MENU
ENTEREXITLAMP
STATUS
POWERON/STAND BY
AUTO ADJ.
SOURCE
VOLUME L-CLICK
MOUSER-CLICK
AUTO ADJ.
ASPECT HELP
FREEZE
PICTURE
S-VIDEO VIDEOCOMPUTER
2LAMP MODE1
SELECT
MENU
ENTEREXITLAMP
STATUS
POWER
ON/STAND BY
AUTO ADJ.
SOURCE
  Selecting a Source
Selecting the computer or video source
NOTE: Turn on the computer or video source equipment connected to the projector.
Selecting from Source List
Press and quickly release the SOURCE button on the projector...

21
3. Projecting an Image (Basic Operation)
 Adjusting the Picture Size and Position
F
O CUSM E
N USELE C T
L A M P
S TA TU S
P O W ERO N/
S TA N
D 
B Y S
O U
RC
E A
UTO  
A DJ.E
N TE REXITZ O OM
F
O C
USM EN USE
LE C T
L A M P
S TA TU
S
P O W E
RO N/S TA ND B Y S
O URCE A
UTO  
A DJ.E
N TE REXITZ O
OM
2
1PUSH
34
Adjustable Tilt Foot
Adjustable Tilt
Foot Button
Place your projector on a flat level surface and ensure that the project\
or is
square to the screen.
Lift the front edge of the projector to...

22
3. Projecting an Image (Basic Operation)
MENUSELE C TLA MP
S TA TUS
PO WERON/ST AND BYSO U
RCEAUTO  A DJ.
ENTERE
XIT
F O CUSZO OM
M EN USELECTLA M P
S TA TU S
P O W ERO N/S TA ND B YSO URCEAUTO  A DJ.
EN TEREXIT
FOCUS
Zoom
Use the ZOOM lever to adjust the image size on the screen.
Focus
Use the FOCUS ring to obtain the best focus.
F
O CUSM EN USE
LE C
T
L A M P
S TA TU
S
P O
W ERO N/S
TA N
D 
B Y S
O
URC
E A
UTO  A D J.E N TE REX
ITZ
O OM