NEC Projector VE303X User Manual

Projector
VE303/VE303X
User’s Manual
Model No.
NP-VE303/NP-VE303X 

Ver. 1 11/15
• Virtual Remote Tool uses WinI2C/DDC library, © Nicomsoft Ltd.• DLP, BrilliantColor, and DLP Link are trademarks of Texas Instruments.• IBM is a trademark or registered trademark of International Business Machines Corporation.•  Macintosh, Mac OS X, iMac, and PowerBook are trademarks of Apple Inc., registered in the U.S. and other countries.•  Microsoft, Windows, Windows Vista, Internet Explorer, and NET Framework are either a registered trademark or trademark of Microsoft Corporation in...

iEnglish ...
Safety Cautions
Precautions
Please read this manual carefully before using your NEC projector and keep the manual handy for future reference.
CAUTION
To turn off main power, be sure to remove the plug from power outlet.The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible.
CAUTION
TO PREVENT SHOCK, DO NOT OPEN THE CABINET.THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE.REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol warns the...

iiEnglish ...
WARNING TO CALIFORNIA RESIDENTS:Handling the cables supplied with this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. WASH HANDS AFTER HANDLING.
RF Interference (for USA only)
WARNINGThe Federal Communications Commission does not allow any modifications or changes to the unit 
EXCEPT those specified by NEC Display Solutions of America, Inc. in this manual. Failure to comply with 
this government regulation...

iiiEnglish ...
  Fire and Shock Precautions  
•  Ensure that there is sufficient ventilation and that vents are unobstructed to prevent the build-up of heat inside your projector. Allow at least 4 inches (10cm) of space between your projector and a wall.•  Do not try to touch the exhaust vent as it can become heated while the projector is turned on and immediately after the projector is turned off.
•  Prevent foreign objects such as paper clips and bits of paper from falling into your projector. Do not...

ivEnglish ...
  Remote Control Precautions
•  Handle the remote control carefully.•  If the remote control gets wet, wipe it dry immediately.•  Avoid excessive heat and humidity.•  Do not short, heat, or take apart batteries.•  Do not throw batteries into fire.•  If you will not be using the remote control for a long time, remove the bat teries. •  Ensure that you have the batteries’ polarity (+/–) aligned correctly. •  Do not use new and old batteries together, or use different types of batteri es...

vEnglish ...
About High Altitude mode 
•    Set [FAN MODE] to [HIGH ALTITUDE] when using the projector at altitu des approximately 2500 feet/760 meters or higher. •    Using the projector at altitudes approximately 2500 feet/760 meters or hig her without setting to [HIGH ALTITUDE] can cause the projector to overheat and the protector could shut down. If this hap-pens, wait a couple minutes and turn on the projector. •    Using the projector at altitudes less than approximately 2500 feet/760 meters and...

1
Table of Contents...............................1
Usage Notice .....................................2
Precautions .........................................2
Introduction ........................................4
Product Features ................................4
Package Overview ..............................5
Product Overview ...............................6
Projector .................................................6
Ports .......................................................7
Control...

2
Precautions
 
Follow all warnings, precautions and maintenance as 
recommended in this user’s guide to maximize the life of your 
unit.
■ Warning-This projector will detect the life of the lamp 
itself. Please be sure to change the lamp when it 
shows warning messages.
■ Warning-Reset the “CLEAR LAMP HOURS” function 
from the on-screen display “OPTIONS 
|LAMP SETTINGS” menu after replacing the 
lamp module. Please see page 61.
■ Warning-When switching the projector off, please ensure 
the cooling cycle...

3
  Do:
■   Turn off the product before cleaning.
■   Use a soft cloth moistened with mild detergent to clean the 
display housing.
■   Disconnect the power plug from AC outlet if the product is not 
being used for a long period of time.
■   If the lens is soiled, use a commercially available cleaning cloth 
for lens.
  Do not:
■   Use abrasive cleaners, waxes or solvents to clean the unit.
■   Use under the following conditions:
-   Extremely heat, cold or humidity.
-   In areas susceptible to excessive...