NEC Projector V311w User Manual

							21
3. Projecting an Image \b\cBasic Operation)
Note on Startup scr\ceen \bMenu Language \cSelect screen)

						

							22
3. Projecting an Image \b\cBasic Operation)
❷ Selecting a Source
Selecting the comput\cer or video source
NOTE:	Turn	on	the	computer	or	video	source	equipment	connected	to	the	projector.
Selecting from Source List
	
						

							23
3. Projecting an Image \b\cBasic Operation)
❸ Adjusting the Pict\cure Size and Positio\cn

						

							24
3. Projecting an Image \b\cBasic Operation)
2
1
4
3
Adjustable	Tilt	 Foot
Ventilation	outlet
Adjustable	Tilt	Foot	Lever
Adjust the Tilt Foo\ct
1.  Lift the front edge of the projector.
 CAUTION:

						

							25
3. Projecting an Image \b\cBasic Operation)
Zoom

						

							26
3. Projecting an Image \b\cBasic Operation)
❹ Correcting Keystone \fis\ctortion
Correcting Keystone \fis\ctortion

						

							27
3. Projecting an Image \b\cBasic Operation)
Adjusting with the\c remote control
1. Press the KEYS\bONE button.
	 The	Keystone	bar	will	be	displayed.
 
2. Use the ◁ or ▷ button to correct t\She keystone distortion.
	 Adjust	so	that	the	right	and	left	sides	are	parallel.
 
3. Press the EN\bER b utton.
NOTE:
•	 The	Keystone	correction	can	cause	an	image	to	be	s\bight\by	b\burred	because	the	correction	is	made	e\bectronica\b\by.
•	 The	maximum	range 	of 	vertica\b 	keystone 	correction 	is 	+/−40 	degrees. 	This 	maximum 	range 	may 	be 	sma\b\ber 	depending 	on 	the 	
signa\b	or	aspect	ratio	setting.	The	Keystone	correction	range	wi\b\b	a\bso	be	sma\b\ber	 when 	 3D 	 mode 	 is 	 enab\bed.
•	 The	range	of	keystone	correction	is	not	the	maximum	ti\bt	ang\be	of	projector.
•	 The	\beft	and	right	(horizonta\b)	keystone	correction	is	not	avai\bab\be.
TIP:	The	changes	can	be	saved	with	[KEYSTONE	SAVE].	(→	page	64) 
						

							28
3. Projecting an Image \b\cBasic Operation)
❺ Optimizing Comput\cer Signal Automatic\cally
Adjusting the Imag\ce Using Auto Adjus\ct

						

							29
3. Projecting an Image \b\cBasic Operation)
❼ Turning off the Projector
To turn off the projector:
1. First,  press  the   (POWER)  button  on  the  projector 
cabinet or the POWER OFF button on the remote con-
trol. 
	 The	[P\bWER	\b FF	/	A RE	Y \bU	S URE?	/ CARB\bN	S AV-
INGS-	SESSI\bN	X.XXX[g-C\b2]]	message	will	appear.
2. Secondly,  press  the  EN\bER  button  or  press  the  
(POWER) or the POWER OFF button again.
	 The	lamp	will 	tur n 	off 	and 	the 	projector 	will 	go 	into 	standb y 	
mode.	When	in 	standb y 	mode \f 	the 	P\b WER 	indicator 	will 	
light	orange	and 	the 	ST ATUS 	indicator 	will 	light 	g reen 	when 	
[N\bRMAL]	is	selected	for	[STANDBY	M\bDE].	
	 Immediately	after	tur ning 	on 	the 	projector 	and 	displa ying 	
an	image\f	y ou 	cannot 	tur n 	off 	the 	projector 	f or 	60 	seconds .
3. Finally, unplug the power cord.
	 The	P\bWER	indicator	will	go	out.

						

							30
3. Projecting an Image \b\cBasic Operation)
❽ After Use