NEC Projector V302X User Manual

							64English ...
User Controls
1. Turn on DHCP to allow the DHCP server to automatically assign 
an IP, or manually enter the required network information.
ENTER CURRENT SECURITY CODE
SECURITY KEYWORD
EXIT
ENTER INVALID-KEYWORD TOO SHORTNETWORK
NETWORK STATUS
DISCONNECT
DHCP
IP ADDRESS
SUBNET MASK
GATEWAY
APPLY OFF
2. 
Then choose apply and press ENTER button to complete the 
configuration process.
3. Open your web browser and type in from the OSD LAN screen 
then the web page will display as below:
How to use web browser to control your projector
	When you used the projector IP address, you can not link to your service server.
	PJLink:  Set a password for PJLink. PJLink is a standardization of protocol used for controlling projectors of different manufacturers. This standard protocol is established by Japan Business Machine and Information System Industries Association (JBMIA) in 2005.The projector supports all the commands of PJLink Class 1.
	AMX BEACON:
Turn on or off for detection from AMX Device Discovery when connecting to the network supported by AMX's NetLinx control system.
	CRESTRON ROOM-VIEW compatibility:The projector supports CRESTRON ROOMVIEW, allowing multiple devices connected in the network to be managed and controlled from a computer or a controller.For more information, visit http://www.crestron.com 
						

							65... English
User Controls
4. Open “Projector Status and Control” to control your projector. 
 
When making a direct connection from your computer to the projector
Step 1: Find an IP Address (default:192.168.0.10) from LAN function of projector.
192.168.0.10
Step 2: Select apply and press the ENTER button on the remote control or the control 
panel to submit function or press the MENU button on the remote control or 
the control panel to exit.
Step 3: To open Network Connections, click Start, click Control Panel, click Network 
and Internet Connections, and then click Network Connections. Click the connection you want to configure, and then, under Network Tasks  , click Change settings of this connection. 
						

							66English ...
User Controls
Step 4: On the General tab, under This connection uses the following items, click 
Internet Protocol (TCP/IP), and then click “Properties.”
Step 5: Click Use the following IP address, and type in as below:
1) IP address: 192.168.0.20 
2) Subnet mask: 255.255.255.0
3) Default gateway:192.168.0.1
Step 6: To open Internet Options, click IE web browser, click Internet Options, click the 
Connections tab and click “LAN Settings...” 
						

							67... English
User Controls
Step 7: The Local Area Network (LAN) Setting dialog box appears, In the Proxy Server 
area, cancel the Use a proxy server for your LAN check box., then click “OK” 
button twice.
Step 8: Open your IE and type in the IP address of 192.168.0.10 in the URL then press 
the ENTER button key. 
						

							68English ...
User Controls
Step 9: Open “Projector Status and Control” to control your projector. 
						

							69... English
User Controls
SCREENIMAGESETTINGOPTIONSGENERALLAMP SETTINGS
INPUT SEARCHINPUTFAN MODEINFORMATION HIDE
BACKGROUND COLORRESET
COMPUTERSELECTEXITMOVEMOVE
BLUE
OFF
OFF
AUTO
ID DISPLAYOFF
 INPUT SEARCH
 ON: The projector will search for other signals if the current input signal is lost. 
 OFF: The projector will only search current input connection.
INPUT SEARCH
OFF
ON
  INPUT
Use this option to enable / disable input sources. Press ENTER to 
enter the sub menu and select which sources you require. Press 
the ENTER button to finalize the selection. The projector will not 
search for inputs that are not selected. 
NP-V332X, NP-332W, NP-V302H
INPUT
COMPUTERHDMI1/MHL
HDMI2
VIDEO
OPTIONS | 
GENERAL 
						

							70English ...
User Controls
NP-V302X, NP-302W
INPUTCOMPUTERHDMI1
HDMI2
VIDEO
  FAN MODE
  AUTO: The built-in fans automatically run at a variable speed 
according to the internal temperature.
  HIGH ALTITUDE: The built-in fans run at high speed.
Select this option when using the projector at altitudes 
approximately 2500 feet/760 meters or higher.
FAN MODE
AUTO
HIGH ALTITUDE
  INFORMATION HIDE
 ON: Choose “ON” to hide the info message.
 OFF: Choose “OFF” to show the “SEARCHING” message.
INFORMATION HIDE
OFFON
  ID DISPLAY
Use this feature to display the ID number which is displayed when 
the "ID SET" button is pressed on the remote control.
ID DISPLAY
OFFON 
						

							71... English
User Controls
	(*) Except “LANGUAGE”, “LOGO”,  “NETWORK”, “SECURITY”, “FAN MODE”, “BACKGROUND COLOR”, “LAMP LIFE REMAINING”, “LAMP HOURS USED”, and “STANDBY MODE”.
 BACKGROUND COLOR
Use this feature to display a “BLACK”or “BLUE” screen when no 
signal is available.
BACKGROUND COLOR
BLACKBLUE
  RESET
Choose “YES” to return the display parameters on all menus to 
the factory default settings. (*)
ARE YOU SURE
YES NO 
						

							72English ...
User Controls
SCREENIMAGESETTINGOPTIONSGENERALLAMP SETTINGS
LAMP LIFE REMAININGLAMP HOURS USEDECO MODELAMP LIFE REMINDER
COMPUTERSELECTEXITMOVEMOVE
OFFOFFCLEAR LAMP HOURS
 LAMP LIFE REMAINING
Showing the Lamp life.
 LAMP HOURS USED
Display the projection time.
 ECO MODE
Choose “ECO” to dim the projector lamp which will lower power 
consumption and extend the lamp life. Choose “OFF” to return to 
normal mode.
ECO MODE
OFFECO
OPTIONS 
| LAMP 
SETTINGS 
						

							73... English
User Controls
 LAMP LIFE REMINDER
Choose this function to show or to hide the warning message 
when the changing lamp message is displayed.  
The message will appear when the lamp has reached the end of its 
life. 
LAMP LIFE REMINDER
OFFON
USE THE SPECIFIED LAMP
FOR SAFETY AND PERFORMANCE. ARE YOU SURE ? YES NO
 CLEAR LAMP HOURS
Reset the lamp hour counter after replacing the lamp.