NEC Projector PX602WL-WH User Manual

88
CORNERSTONE
Display	the	4-point	correction	screen	and	adjust	the	trapezoidal	distortion	of	the	projection	screen.
Please	refer	to 	“Correcting 	Hor izontal 	and 	V ertical 	K eystone 	Distor tion 	[CORNERST ONE]”	(→	page	32)	for	details 	
on	the	operation.
HORIZONTAL	CORNER/VERTICAL	CORNER
Distortion	correction	for	corner	projection	such	as	wall	surfaces.
HORIZONTAL CORNER
 ������������������������������Performs correction for projection onto a wall lying at an angle to the hor\
izontal direction�
*...

89
Adjustment method
1.	 Align	the	cur sor 	with 	the 	[HORIZONT AL 	CORNER] 	or 	[VER TICAL 	CORNER] 	of 	the 	[GEOMETRIC 	CORREC-
TION]	menu	and	then	press	the	ENTER	button.
•	 The	adjustment	screen	will	be	displayed.
2. Press the ▼▲◀▶ buttons to align the cursor (yellow box) with the target adjustment point and then press 
the ENTER button.
•	 The	cursor	will	change	into	an	adjustment	point	(yellow	in	color).
3. Press the ▼▲◀▶	buttons	to	adjust	the	corners	or	sides	of	the	screen	and	then	press	the...

90
PINCUSHION
Adjust	the	curve	distortion	of	the	projection	screen.
TOP ������������������������Adjust the curve distortion of the upper edge of the projection 
screen�
BOTTOM ����������������Adjust the curve distortion of the lower edge of the projection 
screen�
LEFT ����������������������Adjust the curve distortion of the left edge of the projection screen�
RIGHT ��������������������Adjust the curve distortion of the right edge of the projection 
screen�
TOP
LEFT RIGHT
BOTTOM
PC	TOOL
Recall	the...

91
[EDGE BLENDING]
This	adjusts	the 	edges 	(boundar ies) 	of 	the 	projection 	screen 	when 	projecting 	high 	resolution 	videos 	using 	a 	combina-
tion	of	several	projectors	in	the	up,	down,	left	and	right	positions.
MODE
This	enables	or	disables	the	EDGE	BLENDING	function.
When	MODE	is	set	to	ON,	the	TOP, 	 BOTTOM, 	 LEFT, 	 RIGHT 	 and 	 BLACK 	 LEVEL 	 settings 	 can 	 be 	 adjusted.
TOP/BOTTOM/LEFT/RIGHT
This	selects	the	EDGE	BLENDING	locations	on	the	left,	right,	top	and	bottom	on	the	screen....

92
[MULTI SCREEN]
WHITE	BALANCE
This	adjusts	the	white	balance	for	each	projector	when	projecting	using	a	combination	of	several	projectors.
This	can	be	adjusted	when	[MODE]	is	set	to	[ON].
BRIGHTNESS W, BRIGHTNESS R, BRIGHTNESS G, BRIGHTNESS B
 ������������������������������Adjusting the black color of the video�
CONTRAST W, CONTRAST R, CONTRAST G, CONTRAST B
 ������������������������������Adjusting the white color of the video�
PICTURE	SETTING
This	sets	the	division	condition	when	projecting	using	a...

93
Conditions for using tiling
•	 All	the	projectors	need	to	fulfil	the	following	conditions.
•	 The	panel	size	must	be	the	same
•	 The	projection	screen	size	must	be	the	same
•	 The	left	and	right	ends	or	top	and	bottom	ends	of	the	projection	screen	must	be	consistent.
•	 The	settings	for	the	left	and	right	edges	of	the	edge	blending	are	the	same
•	 The	settings	for	the	top	and	bottom	edges	of	the	edge	blending	are	the	same
	 If	the	tiling 	conditions 	are 	satisfied, 	the 	video 	screen 	of 	the...

94
❼ Menu Descriptions & Functions [SETUP]
[MENU]
Selecting	Menu	Language	[LANGUAGE]	
You	can	choose	one	of	29	languages	for	on-screen	instructions.
NOTE:	Your	setting	will	not	be	affected	even	when	[RESET]	is	done	from	the	menu.
Selecting	Menu	Color	[COLOR	SELECT]
You	can	choose	between	two	options	for	menu	color:	COLOR 	 and 	 MONOCHROME.
Turning	On	/	Off	Source	Display	[INPUT	DISPLAY]
This	option	tur ns 	on 	or 	off 	input 	name 	displa y 	such 	as 	HDMI, 	Displa yPort, 	BNC , 	BNC(CV), 	BNC(Y/C),...

95
Turning	On	/	Off	Eco	Message	[ECO	MESSAGE]
This	option	turns	on	or	off	the	following	messages	when	the	projector	is	turned	on.	
The	Eco	Message 	prompts 	the 	user 	to 	sa ve 	energy .	When 	[NORMAL] 	is 	selected 	f or 	[LIGHT 	MODE], 	y ou 	will 	get 	a 	
message	prompting	you	to	select	[ECO1]	or	[ECO2].
When	one	of	the	[LIGHT	MODE]	options	have	been	selected.
To	close	the 	message , 	press 	an y 	one 	of 	the 	b uttons.	The 	message 	will 	disappear 	if 	no 	b utton 	oper ation 	is 	done 	f or 	
30...

96
[INSTALLATION]
Selecting	Projector	Orientation	[ORIENTATION]
This	reorients	y our 	image 	f or 	y our 	type 	of 	projection.	The 	options 	are:	desktop 	front 	projection, 	ceiling 	rear 	projection, 	
desktop	rear	projection,	and	ceiling	front	projection.
NOTE: 
•	 Please	consult	the 	dealer 	if 	you 	require 	special 	installation 	ser vices 	e.g. 	when 	mounting 	the 	projector 	to 	a 	ceiling. 	Never 	install 	
the projector on your own. This may result in the projector falling down\
 and causing...

97
Selecting	Aspect	Ratio	and	Position	for	Screen	[SCREEN	TYPE]
Screen	typeSets	the	aspect	ratio	of	the	projection	screen.
FREEThe	ratio	of 	the 	liquid 	cr ystal 	panel 	is 	selected.	Select 	this 	when 	projecting 	
multi-screen	and	17:9	screen	(2K).
4:3	screenFor	a	screen	with	a	4:3	aspect	ratio
16:9	screenFor	a	screen	with	a	16:9	aspect	ratio
16:10	screenFor	a	screen	with	a	16:10	aspect	ratio
NOTE:
•	
After	changing	the	screen	type,	check	the	setting	of	[ASPECT	RATIO]	in	the	menu.	(→ page 80)
Using...