NEC Np600s Projector User Manual

							
4
4. Convenient Features
 Preventing the Unauthorized Use of the Projector [SECURITY]
A keyword can be set for your projector using the Menu to avoid operation by an unauthorized user. When a keyword 
is set, turning on the projector will display the Keyword input screen. Unless the correct keyword is entered, the pro-
jector cannot project an image. 
• The [SECURITY] setting cannot be cancelled by using the [RESET] of the menu.
To enable the Securty functon:
1. Press the MENU button.
  The menu will be displayed.
2.  Press the SELECT 
 button twice to select [SETUP] and press the SELECT  button or the ENTER button 
to select [GENERAL].
3.  Press the SELECT 
 button to select [INSTALLATION].
4.  Press the SELECT 
 button three times to select [SECURITY] and press the ENTER button.
  The OFF/ON menu will be displayed.
5.   Press the SELECT 
 button to select [ON] and press the ENTER button.
 The [SECURITY KEYWORD] screen will be displayed.
6.  Type in a combination of the four SELECT 
 buttons and press the ENTER button.
NOTE: A keyword must be 4 to 10 digits in length.
  The [CONFIRM KEYWORD] screen will be displayed. 
						

							
4
4. Convenient Features
7. Type in the same combination of SELECT   buttons and press the ENTER button.  
 The confirmation screen will be displayed.
8.  Select [YES] and press the ENTER button.  
 The SECURITY function has been enabled.
To turn on the projector when [SECURITY] s enabled:
1.  Press and hold the POWER button for about 1 second.
  The projector will be turned on and display a message to the effect that the projector is locked.
2.  Press the MENU button.
3.  Type in the correct keyword and press the ENTER button. The projector will display an image.
NOTE: The security disable mode is maintained until the main power is tu\
rned off or unplugging the power cable. 
						

							
44
4. Convenient Features
To dsable the SECURITY functon:
1. Press the MENU button.
  The menu will be displayed.
2.   Select [SETUP] 
→ [INSTALLATION] → [SECURITY] and press the ENTER button.
 The OFF/ON menu will be displayed.
3.  Select [OFF] and press the ENTER button.
  The KEYWORD CONFIRMATION screen will be displayed.
4. Type in your keyword and press the ENTER button.  
  When the correct keyword is entered, the SECURITY function will be disabled.
NOTE: If you forget your keyword, contact your dealer. Your dealer will provide you with your keyword in exchange for your request 
code. Your request code is displayed in the Keyword Confirmation screen. In this example [K992-45L8-JNGJ-4XU9-1YAT-EEA2] is 
a request code. 
						

							
45
4. Convenient Features
30
30
 Using the Optional Remote Mouse Receiver (NP01MR)
The optional remote mouse receiver enables you to operate your computer’s mouse functions from the remote control. 
It is a great convenience for clicking through your computer-generated presentations.
Connectng the remote mouse recever to your computer
If you wish to use the remote mouse function, connect the mouse receiver and computer.
The mouse receiver can be connected directly to the computer’s USB port (type A).
NOTE: Depending on the type of connection or OS installed on your computer, you may have to restart your computer or change 
your computer settings.
When operatng a computer va the remote mouse recever
When connectng usng the USB termnal
For PC, the mouse receiver can only be used with a Windows 98/Me/XP*, Windows 2000, Windows Vista, or Mac OS 
X 10.0.0 or later operating system.
* NOTE: In SP1 or older version of Windows XP, if the mouse cursor will not move correctly, do the following:
Clear  the  Enhance  pointer  precision  check  box  underneath  the  mouse  speed  slider  in  the  Mouse  Properties  dialog  box  [Pointer 
Options tab].
NOTE: Wait at least 5 seconds after disconnecting the mouse receiver before reconnecting it and vice versa. The computer may not 
identify the mouse receiver if it is repeatedly connected and disconnect\
ed in rapid intervals.
Remote mouse receiver
Computer
To USB port of PC or Macintosh
Remote sensor on the remote mouse receiver
7m/22 feet 
						

							
46
4. Convenient Features
Operatng your computer’s mouse from the remote control
You can operate your computer’s mouse from the remote control.PAGE UP/DOWN Button:  scrolls the viewing area of the window or to move to the previous or next slide in Power
-
Point on your computer.
SELECT  Buttons:  moves the mouse cursor on your computer.
MOUSE L-CLICK Button:  works as the mouse left button.
MOUSE R-CLICK Button:  works as the mouse right button.
NOTE:
•  When you operate the computer using the SELECT 
 or  button with the menu displayed, both the menu and the mouse 
pointer will be affected. Close the menu and perform the mouse operation.
• 
The PAGE UP and DOWN buttons do not work with PowerPoint for Macintosh.
About Drag Mode:
By pressing the MOUSE L-CLICK or R-CLICK button for 2 or 3 seconds then releasing, the drag mode is set and the 
drag operation can be performed simply by pressing the SELECT  button. To drop the item, press the MOUSE 
L-CLICK (or R-CLICK) button. To cancel it, press the MOUSE R-CLICK (or L-CLICK) button.
TIP: You can change the Pointer speed on the Mouse Properties dialog box on the Windows. For more information, see the user 
documentation or online help supplied with your computer. 
						

							
47
4. Convenient Features
7 Network Setting by Using an HTTP Browser
Overvew
Connecting  the  projector  to  a  network  allows  the  Alert  Mail  setting  (→  page 49)  and  the  projector  control  from  a 
computer via the network.
To perform the projector control from a web browser, you must have an exclusive application installed on your com-
puter. 
The IP address and subnet mask of the projector can be set on the Network Setting screen of the web browser by 
using an HTTP server function. Please be sure to use “Microsoft Internet Explorer 6.0” or a higher version for the web 
browser. (This device uses “JavaScript” and “Cookies” and the browser should be set to accept these functions. The 
setting method will vary depending on the version of browser. Please refer to the help files and the other information 
provided in your software.)
Access is gained to the HTTP server function by starting the Web browser on the computer via the network connected 
to the projector and enter the following URL.
• Network Setting
  http:///index.html
•  Alert Mail Setting
  http:///lanconfig.html
TIP: 
•  The default IP address is “192.168.0.10”.
•  The exclusive application can be downloaded from our website.
NOTE: 
• If the PROJECTOR NETWORK SETTINGS screen does not appear in the web browser, press the Ctrl+F5 keys to refresh your web 
browser (or clear the cache).
•  The display’s or button’s response can be slowed down or operation may not be accepted depending the settings of your network. 
Should this happen, consult your network administrator.
  The projector may not respond if its buttons are repeatedly pressed in rapid intervals. Should this happen, wait a moment and 
repeat. If you still can’t get any response, turn off and back on the\
 projector.
Preparaton Before Use
Connect the projector to a commercially available LAN cable before engaging in browser operations. (→ page 24)
Operation with a browser that uses a proxy server may not be possible depending on the type of proxy server and the 
setting method. Although the type of proxy server will be a factor, it is possible that items that have actually been set 
will not be displayed depending on the effectiveness of the cache, and the contents set from the browser may not be 
reflected in operation. It is recommended that a proxy server not be used unless it is unavoidable.
Handlng of the Address for Operaton va a Browser
Regarding the actual address that is entered for the address or entered to the URL column when operation of the pro-
jector is via a browser, the host name can be used as it is when the host name corresponding to the IP address of the 
projector has been registered to the domain name server by a network administrator, or the host name corresponding 
to the IP address of the projector has been set in the “HOSTS” file of the computer being used.
Example 1:  When  the  host  name  of  the  projector  has  been  set  to “pj.nec.co.jp”,  access  is  gained  to  the  network 
setting by specifying 
  http://pj.nec.co.jp/index.html
  for the address or the entry column of the URL.
Example 2:  When the IP address of the projector is “192.168.73.1”, access is gained to the mail alert settings by 
specifying 
  http://192.168.73.1/index.html
 for the address or the entry column of the URL. 
						

							
48
4. Convenient Features
Network Settngs
http:// /index.html
DHCP ..................................Enabling this option automatically assigns an IP address to the projector from your DHCP server. 
Disabling this option allows you to register the IP address or subnet mask number obtained from 
your network administrator.
NOTE:
The IP address of the projector is required to change the network settin\
g.
The IP address will not be displayed on the projector’s menu.
Consult your network administrator for the IP address when [ENABLE] is s\
elected for [DHCP].
IP ADDRESS  .......................Set  your  IP  address  of  the  network  connected  to  the  projector  when  [DISABLE]  is  selected  for 
[DHCP].
SUBNET MASK  ...................Set your subnet mask number of the network connected to the projector when [DISABLE] is selected 
for [DHCP].
DEFAULT GATEWAY ................Set your default gateway of the network connected to the projector when [DISABLE] is selected for 
[DHCP].
DNS (PRIMARY)  .................Set your primary DNS settings of the network connected to the projector.
DNS (SECONDARY)  .................Set your secondary DNS settings of the network connected to the projector.
UPDATE  ..............................Reflect your settings.
NOTE:  Close  the  browser  after  clicking  [UPDATE].  The  projector  will  automatically  update  your 
settings.
TIP: Selecting [NETWORK SETTINGS] for [RESET] from the projector’s menu allows you to return the following items to the factory 
default.
[DHCP]: DISABLE
[IP ADDRESS]: 192.168.0.10
[SUBNET MASK]: 255.255.255.0
[DEFAULT GATEWAY]: 192.168.01
*[DNS(PRIMARY)] and [DNS(SECONDARY)] will remain unchanged. 
						

							
49
4. Convenient Features
Alert Mal Settng
http:// /lanconfig.html
This option notifies your computer of an error message via e-mail when using wired LAN. An error message notification 
will be sent when the projector lamp has reached the end of its usable life or an error occurs in the projector.
HOST NAME  ............................Type in the hostname of the network connected to the projector. Up to 60 alphanumeric char-
acters can be used. If the host name is unknown, type in a string of characters representing the 
projector. Example: Projector 1
DOMAIN NAME   ........................Type  in  the  domain  name  of  the  network  connected  to  the  projector.  Up  to  60  alphanumeric 
characters can be used. If the domain name is unknown, type in the right side of @ in the sender’s 
address. Example: nec. com
ALERT MAIL  .............................Checking [ENABLE] will turn on the Alert Mail feature. 
Checking [DISABLE] will turn off the Alert Mail feature.
SENDER’S ADDRESS  ................Type in the senders address. Up to 60 alphanumeric and symbols characters can be used.
SMTP SERVER NAME  ...............Type in the SMTP server name to be connected to the projector. Up to 60 alphanumeric characters 
can be used.
RECIPIENT’S ADDRESS 1 to 3  ....Type in your recipient’s address. Up to 60 alphanumeric and symbols characters can be used.
APPLY  .......................................Click this button to reflect the above settings
EXECUTE  ..................................Click this button to send a test mail to check if your settings are corr\
ect.
STATUS  .....................................A reply to a test mail will be displayed.
NOTE:
•  If you execute a test, you may not receive an Alert mail. Should this ha\
ppen, check if the network settings are correct.
•  If you entered an incorrect address in a test, you may not receive an Alert mail. Should this happen, check if the Recipient ’s Ad
-
dress is correct
TIP: The Alert Mail settings will not be affected even when [RESET] is done f\
rom the menu. 
						

							
50
4. Convenient Features
 Using the VGA Signal Cable to Operate the Projector 
(Virtual Remote)
Overvew
The projector supports DDC/CI (Display Data Channel Command Interface) that is a standard interface for bidirectional 
communication between display/projector and computer. 
The optional utility software “Virtual Remote Tool” designed exclusively for our projector is required to use DDC/CI.
Check with our website.
http://www.nec-display.com/dl/en/index.html
NOTE: Use the supplied VGA signal cable to connect the COMPUTER 1 IN connector directly with the monitor output connector of 
the computer to use Virtual Remote Tool. Using a switcher, scan converter or other cables than the supplied VGA signal cable may 
cause failure in signal communication. 
						

							
5
5. Using On-Screen Menu
1 Using the Menus
NOTE: The on-screen menu may not be displayed correctly while interlaced motion video image is projected.
1. Press the MENU button on the remote control or the projector cabinet to display the menu.
NOTE: The commands such as ENTER, EXIT, ,  in the bottom show available buttons for your operation.
2.  Press the SELECT 
 buttons on the remote control or the projector cabinet to display the submenu.
3.  Press the ENTER button on the remote control or the projector cabinet to highlight the top item or the first 
tab.
4.  Use the SELECT 
 buttons on the remote control or the projector cabinet to select the item you want to 
adjust or set.
  You can use the SELECT 
 buttons on the remote control or the projector cabinet to select the tab you 
want.
5.  Press the ENTER button on the remote control or the projector cabinet to display the submenu window.
6.  Adjust  the  level  or  turn  the  selected  item  on  or  off  by  using  the  SELECT 
  buttons  on  the  remote 
control or the projector cabinet.
Changes are stored until adjusted again.
7.  Repeat steps 2 -6 to adjust an additional item, or press the EXIT button on the remote control or the projec
-
tor cabinet to quit the menu display.
NOTE: When a menu or message is displayed, several lines of information may be lost, depending on the signal or settings.
8.   Press the MENU button to close the menu.
  To return to the previous menu, press the EXIT button.