NEC Np600s Projector User Manual

							

1. Introduction
 Introduction to the Projector
This section introduces you to your new projector and describes the features and controls.
Congratulations on Your Purchase of the Projector
This projector is one of the very best projectors available today. The projector enables you to project precise images 
up to 300 inches (110 inches on NP600S; 104 inches on NP500WS) across (measured diagonally) from your PC or 
Macintosh computer (desktop or notebook), VCR, DVD player, or document camera.
You can use the projector on a tabletop or cart, you can use the projector to project images from behind the screen, 
and the projector can be permanently mounted on a ceiling*1. The remote control can be used wirelessly.
*1 Do not attempt to mount the projector on a ceiling yourself.
  The projector must be installed by qualified technicians in order to ensure proper operation and reduce the risk 
of bodily injury.
  In addition, the ceiling must be strong enough to support the projector and the installation must be in accordance 
with any local building codes. Please consult your dealer for more information.
 
Features you’ll enjoy:
•  Quck start & Drect Power Off
  Eight seconds after turning on the power, the projector is ready to display PC or video images.
  The projector has a feature called “Direct Power Off ”. This feature allows the projector to be turned off (even when 
projecting an image) using a power strip equipped with a switch and a breaker.
•  AUTO POWER ON and AUTO POWER OFF features
  The AUTO POWER ON(AC), AUTO POWER ON(COMP1), AUTO POWER OFF, and OFF TIMER features eliminate 
the need to always use the POWER button on the remote control or projector cabinet.
•  Short throw dstances (NP600S/NP500WS)
  Short focal lenses provide for a larger image using a shorter throw distance when compared to a typical projector 
lens.
•  Vrtual Remote functon
  The Virtual Remote function allows power On/Off and source selection of the projector from your PC by using the 
supplied VGA signal cable. The utility software “Virtual Remote Tool” exclusively for the projector is required to be 
downloaded from our website.
•  The optonal remote control (NP0RC) allows you to assgn a CONTROL ID to the projector
  Multiple projectors can be operated separately and independently with the same single remote control by assigning 
an ID number to each projector.
•  A varety of nput ports and a comprehensve array of system control nterfaces
  This projector supports input signals on the following ports: DVI-I connector (DVI-I 29 Pin) with HDCP compatible, 
15pin D-Sub, composite and S-video.
•  Integrated RJ-45 connector for wred networkng capablty
  An RJ-45 connector is equipped as standard feature.
•  7W bult-n speaker for an ntegrated audo soluton
  Powerful 7 watt speaker provides volume need for large rooms.
•  Auto vertcal keystone correcton
  Auto Keystone feature allows the projector to detect its tilt and correct vertical distortion automatically.
•  LCD projector wth hgh resoluton and hgh brghtness
  High resolution display - up to UXGA compatible, XGA (NP600/NP500/NP400/NP300/NP600S)/WXGA (NP500W/
NP500WS) native resolution. 
						

							

1. Introduction
• Sx pcture preset modes for user adjustable pcture and color settngs
  Each picture preset mode can be customized and memorized according to your preference.
•  Preventng unauthorzed use of the projector
  Enhanced  smart  security  settings  for  keyword  protection,  cabinet  control  panel  lock,  security  slot,  and  security 
chain opening to help prevent unauthorized access, adjustments and theft deterrence.
•  PC Control Port
  You can control the projector with a PC or control system using the PC Co\
ntrol port.
•  W n standby condton wth energy savng technology
  Selecting [POWER-SAVING] for [STANDBY MODE] from the menu can put the projector in power-saving mode 
that consume less power than the normal standby condition.
•  Optonal remote mouse recever
  You  can  use  the  supplied  wireless  remote  control  and  the  optional  remote  mouse  receiver  to  operate  your  PC 
mouse  from  across  the  room. The  optional  remote  mouse  receiver  (NP01MR)  supports  almost  any  PC  using  a 
USB connection.
About this user’s manual
The fastest way to get started is to take your time and do everything right the first time. Take a few minutes now to 
review the user’s manual. This may save you time later on. At the beginning of each section of the manual you’ll find 
an overview. If the section doesn’t apply, you can skip it. 
						

							
4
1. Introduction
Comparatve Table of Man Features
The main features vary depending on the model as follows.
Standard ModelsWide Panel ModelShort-Throw ModelWide Panel & Short-Throw Model
NP600NP500NP400NP300NP500WNP600SNP500WS
Native Aspect Ratio(→ page 85, 87)StandardWideStandardWide
Native Resolution (dots x lines*1)(→ page 85, 87)XGA (1024 x 768)WXGA  (1280 x 800)XGA  (1024 x 768)WXGA  (1280 x 800)
Screen Size(→ page 85, 87)21"–300"60"–110"57"–104"
Throw Distance(→ page 85, 87)29–444 inches/0.7–11.3 m28–419 inches/ 0.7–10.6 m35"–66"/ 0.9 m–1.7 m36"–66"/0.9 m–1.7 m
Light output*2*3 in NORMAL mode(→ page 85, 87)
3500 lumens3000 lumens2600 lumens2200 lumens3000 lumens2600 lumens2100 lumens
Zoom(→ page 32)Using the manual zoom leverUsing the [DIGITAL ZOOM] function from the menu
Focus(→ page 33)Using the manual focus ringUsing the manual focus lever
Lamp Replace-ment Time (aver-age)(→ page 73)
3000 (H) in NORMAL /4000 (H) in ECO
For further details on the specifications, see page 85.
*1  Effective pixels are more than 99.99%.
*2  This is the light output value (lumens) when the [PRESET] mode is set to [HIGH-BRIGHT]. If any other mode is 
selected as the [PRESET] mode, the light output value may drop slightly.
*3  Compliance with ISO21118-2005
TIP: The model name is located on the cabinet.
Model name
SELECT
MENU
EXITENTER
STATUSLAMPAUTO ADJ.SOURCE
FOCUS 
						

							
5
1. Introduction
STATUSLAMPAUTOADJ.SOURCESELECTMENUEXITENTER
FOC US
 Part Names of the Projector
Front/Top
NP600/NP500/NP400/NP00/NP500W
Zoom Lever (→ page 32)
Controls(→ page 7)
Lens
Lens Cap
Built-in Security Slot (  )*
Focus Ring(→ page 33)
Remote sensor(→ page 10)
Ventilation (inlet) / Filter Cover(→ page 76)
* This security slot supports the MicroSaver ® Security System.
Adjustable Tilt Foot (→ page 31)
Adjustable Tilt Foot Lever (→ page 31)
Security chain opening Attach an anti-theft device.The security chain opening accepts se-curity wires or chains up to 0.18 inch/ 4.6 mm in diameter.
NP600S/NP500WS
STATUSLAMPAUTOADJ.SOURCESELECTMENUEXITENTER
FOCUS
Controls(→ page 7)
Lens
Lens Cap
Built-in Security Slot (  )*
Focus Lever(→ page 33)
Remote sensor(→ page 10)
Ventilation (inlet) / Filter Cover(→ page 76)
Adjustable Tilt Foot (→ page 31)
Adjustable Tilt Foot Lever (→ page 31)
Security chain opening Attach an anti-theft device.The security chain opening accepts se-curity wires or chains up to 0.18 inch/ 4.6 mm in diameter.
* This security slot supports the MicroSaver ® Security System. 
						

							
6
1. Introduction
SELECTMENUEXITENTER
STATUSLAMPAUTOADJ.SOURCE
FOCUS
AC InputConnect the supplied power cable’s two-pin plug here, and plug the other end into an active wall outlet. (→ page 25)
Main Power SwitchWhen you plug the supplied power cable into an active wall outlet and turn on the Main Power, the POWER indicator turns orange and the projector is in standby mode.(→ page 26, 38)
Terminal Panel (→ page 8)
Monaural Speaker (7W)
Ventilation (outlet)Heated air is exhausted from here.
Ventilation (inlet) / Filter Cover(→ page 76)
Lamp Cover (→ page 80)
Rear Foot (→ page 31)
Spacer (black rubber)To fine-adjust the height of the rear foot, remove the spacer and rotate the rear foot to the desired height.
Rear 
						

							
7
1. Introduction
Top Features
SELECT 
MENU 
EXIT ENTER 
STATUS LAMP 
AUTO ADJ. SOURCE 
1 25 6
4
7
8
109
3
.  (POWER) Button (→page 27, 38)
.  POWER Indcator 
(→page 26, 38, 82)
.  STATUS Indcator 
(→page 82)
4.  LAMP Indcator 
(→page 79, 82)
5.  SOURCE Button 
(→page 29)
6.  AUTO ADJ. Button 
(→page 37)
7.  MENU Button 
(→page 51)
8.  SELECT 
 / Volume Buttons  / Keystone 
Buttons  (→page 34, 37)
9.  ENTER Button 
(→page 51)
0.  EXIT Button 
(→page 51) 
						

							
8
1. Introduction
Terminal Panel Features
6
87
332 1
5 4
9 10
. COMPUTER  IN/ Component Input Connector 
(Mn D-Sub 5 Pn)
 (→page 17, 20, 22)
.  COMPUTER   (DVI-I) IN Connector (9 Pn) (HDCP 
compatble) 
(→page 19, 20)
.  AUDIO IN Mn Jack (Stereo Mn) 
 
(→page 17, 19, 22)
4.  AUDIO OUT Mn Jack (Stereo Mn)
 (→page 21)
5.  MONITOR OUT (COMP  ) Connector (Mn D-Sub 
5 Pn) 
(→page 21)
6.  S-VIDEO IN Connector (Mn DIN 4 Pn)
  (
→page 23)
7.  VIDEO IN Connector (RCA)
 (→page 23)
8.  AUDIO Input Jacks L/R (RCA)
 (→page 23)
9.  PC CONTROL [PC CONTROL] Port (D-Sub 9 Pn)
  
(→page 93)
  Use  this  por t  to  connect  a  PC  or  control  system. 
This enables you to control the projector using serial 
communication  protocol.  If  you  are  writing  your  own 
program, typical PC control codes are on page 93.
0.  LAN Port (RJ-45)
 (→page 24) 
						

							
9
1. Introduction
 Part Names of the Remote Control
. Infrared Transmtter
  (
→ page 10)
.  POWER ON Button
  (
→ page 27)
.  POWER OFF Button
  (
→ page 38)
4.  MAGNIFY (+)(–) Button
  (
→ page 40)
5.  PIC-MUTE Button
  (
→ page 40)
6.  PAGE UP/DOWN Button*
  (
→ page 45, 46)
7.  MENU Button
  (
→ page 51)
8.  SELECT 
 Button (→ page 51)
9.  ENTER Button 
(→ page 51)
0.  EXIT Button 
(→ page 51)
.  MOUSE L-CLICK Button*
  (
→ page 45, 46)
VOLUME
L-CLICK
ENTEREXIT
MENU
UPMAGNIFYPAGE
OFF
POWER
ON
PIC-MUTE
DOWN
MOUSER-CLICK
COMPUTER
ASPECTHELP
FREEZEPICTURE
S-VIDEO
VIDEOCOMPUTERAUTO ADJ.
LAMP MODE2
1
1
3
4
7
6
9
2
8
10
11
13
14
12
21
22
20
16
15
18
5
17
19
. MOUSE R-CLICK Button*
  (
→ page 45, 46)
.  VIDEO Button
  (
→ page 29)
4.  S-VIDEO Button
  (
→ page 29)
5.  COMPUTER / Button
  (
→ page 29)
6.  AUTO ADJ. Button
  (
→ page 37)
7.  VOLUME (+)(–) Button
  (
→ page 37)
8.  LAMP MODE Button 
(→ page 41)
9.  ASPECT Button
  (
→ page 60)
0.  PICTURE Button
  (
→ page 56, 57)
.  HELP Button
  (
→ page 73)
.  FREEZE Button
  (
→ page 40)
*  The PAGE UP/DOWN, MOUSE L-CLICK and MOUSE R-CLICK buttons work only when the optional remote mouse 
receiver is connected with your computer. 
						

							
0
1. Introduction
Remote Control Precautions
• Handle the remote control carefully.
•  If the remote control gets wet, wipe it dry immediately.
•  Avoid excessive heat and humidity.
•  Do not heat, take apart, or throw batteries into fire.
•  If you will not be using the remote control for a long time, remove the batteries.
•  Ensure that you have the batteries’ polarity (+/-) aligned correctly.
•  Do not use new and old batteries together, or use different types of batteries together.
•   Dispose of used batteries according to your local regulations.
Operating Range for Wireless Remote Control
Press  firmly  and  slide  the 
battery cover off.
Install  new  batteries  (AAA).  En-
sure that you have the batteries’ 
polarity (+/–) aligned correctly.
•  The infrared signal operates by line-of-sight up to a distance of about 22 feet/7 m and within a 60-degree angle of 
the remote sensor on the projector cabinet.
•  The projector will not respond if there are objects between the remote control and the sensor, or if strong light falls 
on the sensor. Weak batteries will also prevent the remote control from properly operating the projector.
Battery Installation
SELECT MENU EXIT ENTER 
STATUS LAMP AUTO ADJ. SOURCE FOCUS 30°
30°
30°
30°
7m/22feet
7m/22feet
Remote control
Remote sensor on projector cabinet
Slip the cover back over the bat-
teries until it snaps into place. Do 
not mix different types of batteries 
or new and old batteries.
Remote control 
						

							

2. Installation and Connections
SELECTMENUEXITENTERSTATUSLAMPAUTOADJ.SOURCEFOCUS
This section describes how to set up your projector and how to connect video and audio sources.
Your projector is simple to set up and use. But before you get started, you must first:
z  Set up a screen and the projector.
x  Connect your computer or video equip-
ment to the projector.
  (
→ page 17, 19, 20, 21, 22, 23, 24)
c Connect  the  supplied  power  cable. 
(→ page 25)
NOTE: Ensure that the power cable and any other 
cables are disconnected before moving the projec-
tor. When moving the projector or when it is not 
in use, cover the lens with the lens cap.
1 Setting Up the Screen and the Projector
Selecting a Location
NOTE: Throw distances vary depending on the model.
[NP600/NP500/NP400/NP00]
The  further  your  projector  is  from  the  screen  or  wall,  the  larger  the  image. The  minimum  size  the  image  can  be  is 
approximately  21"  (0.53  m)  measured  diagonally  when  the  projector  is  roughly  30  inches  (0.8  m)  from  the  wall  or 
screen. The largest the image can be is 300" (7.6 m) when the projector is about 407 inches (10.3 m) from the wall 
or screen.
300
240
Distance 
(Unit: m/inch)
Lens center
Screen Size
Screen Size (Unit: cm/inch)
200
180
150
120
100
80
10.3/4078.3/325
6.2/244
5.1/203
4.1/162
3.4/1352.7/1072.0/811.3/53
40
6.9/271
60
SELECTMENUEXITENTERSTATUSLAMPAUTOADJ.SOURCEFOCUS
3021
1.0/400.8/30
609.6(W)�457.2(H) / 240(W)�180(H)
487.7(W)�365.8(H) / 192(W)�144(H)
406.4(W)�304.8(H) / 160(W)�120(H)
304.8(W)�228.6(H) / 120(W)�90(H)
365.8(W)�274.3(H) / 144(W)�108(H)
243.8(W)�182.9(H) / 96(W)�72(H)
203.2(W)�152.4(H) / 80(W)�60(H)
162.6(W)�121.9(H) / 64(W)�48(H)
121.9(W)�91.4(H) / 48(W)�36(H)
81.3(W)�61.0(H) / 32(W)�24(H)
61.0(W)�45.7(H) / 24(W)�18(H)42.7(W)�32(H) / 17(W)�13(H)
TIP:
•  The distances are indicated by intermediate values between tele and wide. Use as a rule of thumb.
•  The Zoom lever adjusts the image size by up to +/-10%.
•  For more details on throw distance, see page 
15.
To the wall outlet.