NEC Np600s Projector User Manual

							
8
7. Appendix
1 Troubleshooting
This section helps you resolve problems you may encounter while setting up or using the projector.
Indicator Messages
Power Indicator
Indcator CondtonProjector CondtonNote
OffThe main power is off–
Blinking lightGreen0.5 sec On,0.5 sec OffThe projector is getting ready to turn on.Wait for a moment.
2.5 sec On,0.5 sec OffOff Timer is enabled. 
–
Orange0.5 sec On,0.5 sec OffThe projector is cooling down.Wait for a moment.
Steady lightGreenThe projector is turned on.–
OrangeThe projector is in Standby.–
Status Indicator
Indcator Condton
Projector CondtonNote
OffNormal  or  Standby  ([POWER-SAVING]  for [STANDBY MODE])–
Blinking lightRed1  cycle  (0.5  sec  On, 2.5 sec Off)Lamp cover error or lamp housing errorReplace  the  lamp  cover  or  lamp housing correctly.
2  cycle  (0.5  sec  On, 0.5 sec Off)Temperature errorThe projector is overheated. Move the projector to a cooler location.
3  cycle  (0.5  sec  On, 0.5 sec Off)Power errorPower  unit  is  not  working  properly. Contact your dealer.
4  cycle  (0.5  sec  On, 0.5 sec Off)Fan errorFans will not work correctly.
6  cycle  (0.5  sec  On, 0.5 sec Off)Lamp errorLamp fails to light. Wait a full minute and then turn on again.
GreenRe-firing the lamp (The projector is cooling down.)The projector is re-firing.Wait for a moment.
Steady lightGreenStandby ([NORMAL] for [STANDBY MODE])–
OrangeCabinet button is lockedYou  have  pressed  cabinet  button when Cabinet Button is locked.
Lamp Indicator
Indcator CondtonProjector CondtonNote
OffNormal–
Blinking lightRedLamp has reached its end of life. Lamp re-placement message will be displayed.Replace the lamp.
Steady lightRedLamp  has  been  used  beyond  its  limit.  The projector  will  not  turn  on  until  the  lamp  is replaced.
Replace the lamp.
GreenLamp mode is set to Eco mode–
Over-Temperature Protecton
If the temperature inside the projector rises too high, the over-temperature protector will automatically turn off the lamp 
with the STATUS indicator blinking (2-cycle On and Off.)
Should this happen, do the following:
• Unplug the power cable after the cooling fans stop.
•  Move the projector to a cooler location if the room where you are presenting is particularly too warm.
•  Clean the ventilation holes if they are clogged with dust.
•  Wait about 60 minutes until the inside of the projector becomes cool enough. 
						

							
8
7. Appendix
Common Problems & Solutions (→ “Power/Status/Lamp Indicator” on page 82.)
Does not turn onor shut down
Will turn off
No picture
Picture suddenly becomes dark
Color tone or hue is unusual
Image isn’t square to the screen
Picture is blurred
Flicker appears on screen
Image is scrolling vertically, horizontally or both
Remote control does not work
Indicator is lit or blinking
Cross color in RGB mode
Problem Check These Items
For more information contact your dealer.
• Check  that  the  power  cable  is  plugged  in  and  that  the  power  button  on  the  projector  cabinet  or  the  remote control is on. (→ pages 25 and 38)
•  Ensure that the lamp cover is installed correctly. (→ page 81)
•  Check to see if the projector has overheated. If there is insufficient ventilation around the projector or if the 
room where you are presenting is particularly warm, move the projector t\
o a cooler location.
•  Check to see if the lamp usage exceeds 3100 hours (up to 4100 hours : E\
co mode). If so, replace the lamp.
  After replacing the lamp, reset the lamp hours used. (
→ page 75)
•  The lamp may fail to light. Wait a full minute and then turn on the power again.
•  Set  [FAN  MODE]  to  [HIGH  ALTITUDE]  when  using  the  projector  at  altitudes  approximately  5500  feet/1600 
meters or higher. Using the projector at altitudes approximately 5500 feet/1600 meters or higher without setting to [HIGH ALTITUDE] can cause the projector to overheat and the projector could shut down. If this happens, wait a couple minutes and turn on the projector. (→ page 69)
  Also when the lamp is turned off, the projector internal temperature is \
hot. If the power is turned on before 
the projector has cooled down, the fan will run a short time before the \
lamp will turn on.
•  Ensure that the [OFF TIMER] or [AUTO POWER OFF] is off. (
→ page 71, 72)
•  Use  the  COMPUTER1,  the  COMPUTER2,  the  VIDEO  or  the  S-VIDEO  button  on  the  remote  control  to  select 
your source (Computer, Video or S-Video). (→ page 29) If there is still no picture, press the button again.
•  Ensure your cables are connected properly.
•  Use menus to adjust the brightness and contrast. (
→ page 57)
•  Remove the lens cap.
•  Reset the settings or adjustments to factory preset levels using the [RESET] in the Menu. (
→ page 75)
•  Enter your registered keyword if the Security function is enabled. (→ page 42)
•  Be sure to connect the projector and notebook PC while the projector is in standby mode and before turning 
on the power to the notebook PC.In  most  cases  the  output  signal  from  the  notebook  PC  is  not  turned  on  unless  connected  to  the  projector before being powered up.
* If the screen goes blank while using your remote control, it may be the result of the computer’s screen-saver 
or power management software.
•  See also the next page.
•  Check if the projector is in the Forced ECO mode because of too high ambient temperature. If this is the case, 
lower the internal temperature of the projector by selecting [HIGH] for \
[FAN MODE]. (→ page 69)
•  Check if an appropriate color is selected in [WALL COLOR]. If so, select an appropriate option. (
→ page 64)
•  Adjust [HUE] in [PICTURE]. (→ page 57)
•  Reposition the projector to improve its angle to the screen. (
→ page 30)
•  Use the Keystone correction function to correct the trapezoid distortion\
. (→ page 34)
•  Adjust the focus. (
→ page 33)
•  Reposition the projector to improve its angle to the screen. (→ page 30)
•  Ensure  that  the  distance  between  the  projector  and  screen  is  within  the  adjustment  range  of  the  lens. (→ page 15)
•  Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on. 
Should this happen, let the projector stand until there is no condensati\
on on the lens.
•  
Set [FAN MODE] to other than [HIGH ALTITUDE] mode when using the projector at altitudes approximately 5500 feet/1600 meters or lower. Using the projector at altitudes less than approximately 5500 feet/1600 meters and setting to [HIGH ALTITUDE] can cause the lamp to overcool, causing the image to flicker. Switch [FAN MODE] to [AUTO]. (→ page 69)
•  Use  the  COMPUTER1,  the  COMPUTER2,  the  VIDEO  or  the  S-VIDEO  button  on  the  remote  control  to  select your source (Computer, Video or S-Video). (→ page 29)
•  Adjust the computer image manually with the Horizontal/Vertical in the [IMAGE OPTIONS]. (→ page 59)
•  Install new batteries.(
→ page 10)
•  Make sure there are no obstacles between you and the projector.
•  Stand within 22 feet (7 m) of the projector. (
→ page 10)
•  See the POWER/STATUS/LAMP Indicator. (
→ page 82)
•  Press the AUTO ADJ. button on the projector cabinet or the remote contro\
l. (
→ page 37)•  Adjust the computer image manually with [CLOCK]/[PHASE] in [IMAGE OPTION\
S] in the menu. (→ page 58) 
						

							
84
7. Appendix
If there s no pcture, or the pcture s not dsplayed correctly.
• Power on process for the projector and the PC.
  Be sure to connect the projector and notebook PC while the projector is in standby mode and before turning on 
the power to the notebook PC.
  In most cases the output signal from the notebook PC is not turned on unless connected to the projector before 
being powered up.
NOTE: You can check the horizontal frequency of the current signal in the projector’s menu under Information. If it reads “0kHz”, 
this means there is no signal being output from the computer. (→ page 74 or go to next step)
•  Enabling the computer’s external display.
  Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projector.  
When using a PC compatible laptop, a combination of function keys will enable/disable the external display.  Usu-
ally, the combination of the ‘Fn” key along with one of the 12 function keys gets the external display to come on or 
off.  For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle through 
external display selections.
•  Non-standard signal output from the computer
  If  the  output  signal  from  a  notebook  PC  is  not  an  industry  standard,  the  projected  image  may  not  be  displayed 
correctly. Should this happen, deactivate the notebook PC’s LCD screen when the projector display is in use. Each 
notebook PC has a different way of deactivate/reactivate the local LCD screens as described in the previous step. 
Refer to your computer’s documentation for detailed information.
•  Image displayed is incorrect when using a Macintosh
  When using a Macintosh with the projector, set the DIPswitch of the Mac adapter (not supplied with the projector) 
according to your resolution. After setting, restart your Macintosh for the changes to take affect.
  For setting display modes other than those supported by your Macintosh and the projector, changing the DIP switch 
on a Mac adapter may bounce an image slightly or may display nothing. Should this happen, set the DIP switch 
to the 13” fixed mode and then restart your Macintosh. After that, restore the DIP switches to a displayable mode 
and then restart the Macintosh again.
NOTE: A Video Adapter cable manufactured by Apple Computer is needed for a PowerBook which does not have a mini D-Sub 
15-pin connector.
•  Mirroring on a PowerBook
*  When using the projector with a Macintosh PowerBook, output may not be set to 1024 x 768 unless “mirroring” 
is off on your PowerBook. Refer to owner’s manual supplied with your Macintosh computer for mirroring.
•  Folders or icons are hidden on the Macintosh screen
  Folders or icons may not be seen on the screen. Should this happen, select [View] 
→ [Arrange] from the Apple 
menu and arrange icons. 
						

							
85
7. Appendix
 Specifications
This section provides technical information about projector’s performance.
Model Number NP600/NP500/NP400/NP00/NP500W
Optical
NP600/NP500/NP400/NP00NP500W
LCD PanelNP600/NP500: 0.63 inch LCD with Micro Lens Array (Aspect Ratio 4:3)
NP400/NP00: 0.63 inch LCD (Aspect Ratio 4:3)
0.59 inch LCD with Micro Lens Array (Aspect Ratio 16:10)
Resolution1024  768 pixels*11280  800 pixels*1
LensManual zoom and focus
Zoom Ratio= 1–1.2F1.7–2.0  f= 19.8–23.7 mmZoom Ratio= 1–1.2F1.7–1.9  f= 17.7–21.2 mm
LampNP600: 230W AC (168W in ECO Mode)
NP500/NP400/NP 00:  210W  AC  (168W  ECO Mode)
230W AC (168W in ECO Mode)
Light Output*2*3NP600: 3500 lumens (approx. 70% in ECO Mode)NP500: 3000 lumens (approx. 80% in ECO Mode)NP400: 2600 lumens (approx. 80% in ECO Mode)
NP00: 2200 lumens (approx. 80% in ECO Mode)
3000 lumens (approx. 70% in ECO Mode)
Contrast Ratio*3
(full white: full black)500:1
Image Size (Diagonal)21–300 inches/ 0.53 m–7.6 m
Projection Distance29–444 inches/0.7–11.3 m28–419 inches/0.7–10.6 m  
Projection AngleTele: 7.9°–8.3°/Wide: 9.5°–10.0°Tele: 7.6°–7.9°/Wide: 9.1°–9.5°
*1  Effective pixels are more than 99.99%.
*2  This  is  the  light  output  value  (lumens)  when  the  [PRESET]  mode  is  set  to  [HIGH-BRIGHT].  If  any 
other mode is selected as the [PRESET] mode, the light output value may drop slightly.
*3  Compliance with ISO21118-2005
Electrical
Inputs1 RGB/Component (D-Sub 15 P), 1 RGB (Digital/Analog, DVI-I 29 P, HDCP*4 supported), 1 S-Video (DIN 4 P), 1 Video (RCA), 1 (L/R) RCA Audio, 2 Stereo Mini Audio
Outputs1 RGB (D-Sub 15P), 1 Stereo Mini Audio
PC Control1 PC Control Port (D-Sub 9P)
Wired LAN PortRJ-45
External ControlRS232, IR, Wired LAN
Color Reproduction16.7 million colors simultaneously, Full color
Compatible Signals*5Analog: VGA/SVGA/XGA/WXGA/WXGA+/SXGA/SXGA+/UXGA 480i/480p/576i/576p/720p/1080iDigital: VGA/SVGA/XGA/WXGA/SXGA
Video BandwidthRGB: 80 MHz (Max.)
Horizontal Resolution540 TV lines: NTSC/NTSC4.43/PAL/PAL-M/PAL-N/PAL60300 TV lines: SECAM
Scan RateHorizontal: 15 kHz to 100 kHz (RGB: 24 kHz or over)Vertical: 50 Hz to 120 Hz
Sync CompatibilitySeparate Sync / Composite Sync / Sync on G
Built-in Speaker7W (monaural)
*4 What is HDCP/HDCP technology?
  HDCP is an acronym for High-bandwidth Digital Content Protection. High bandwidth Digital Content 
Protection (HDCP) is a system for preventing illegal copying of video data sent over a Digital Visual Interface (DVI).
  If  you  are  unable  to  view  material  via  the  DVI  input,  this  does  not  necessarily  mean  the  projector 
is not functioning properly. With the implementation of HDCP, there may be cases in which certain content is protected with HDCP and might not be displayed due to the decision/intention of the HDCP community (Digital Content Protection, LLC). 
						

							
86
7. Appendix
*5 An image with higher or lower resolution than the projector’s native resolution (NP600/NP500/NP400/NP300: 1024  768 / NP500W: 1280  800) will be displayed with Advanced AccuBlend.
Power Requirement N P 6 0 0 / N P 5 0 0 / N P 4 0 0 / N P 0 0 :  1 0 0 – 2 4 0 V   AC, 50/60Hz
NP600G/NP500G/NP400G/NP 00G:  200–240V AC, 50/60Hz
NP500W: 100–240V AC, 50/60HzNP500WG: 200–240V AC, 50/60Hz
Input CurrentNP600: 3.8–1.5A
NP500/NP400/NP00: 3.5–1.4ANP600G: 1.8A
NP500G/NP400G/NP00G: 1.6A
NP500W: 3.8–1.5ANP500WG: 1.8A
Power ConsumptionNP600: 325W in Lamp NORMAL Mode
NP500/NP400/NP 00:  295W  in  Lamp  NORMAL Mode
NP600/NP500/NP400/NP00: 240W in Lamp ECO Mode/11W in STANDBY Mode/3W in POWER-SAV-ING Mode
325W  in  Lamp  NORMAL  Mode/:  240W  in  Lamp ECO Mode/11W in STANDBY Mode/3W in POWER-SAVING Mode
Mechanical
InstallationOrientation: Desktop/Front, Desktop/Rear, Ceiling/Front, Ceiling/Rear
Dimensions12.1" (W)  3.7" (H)  10.3" (D) /308 mm (W)  93.5 mm (H)  262 mm (D) (not including protrusions)
Weight6.57 lbs / 2.98 kg
Environmental ConsiderationsOperational Temperatures : 41° to 104°F (5° to 40°C), (ECO mode selected automatically at 95°F to 104°F/35°C to 40°\
C) 20% to 80% humidity (non-condensing) Storage Temperatures : 14° to 122°F (-10° to 50°C), 20% to 80% humidity (non-condensing)
RegulationsUL/C-UL Approved (UL 60950-1, CSA 60950-1)Meets DOC Canada Class B requirementsMeets FCC Class B requirementsMeets AS/NZS CISPR.22 Class BMeets EMC Directive (EN55022, EN55024, EN61000-3-2, EN61000-3-3)Meets Low Voltage Directive (EN60950-1, TÜV GS Approved) 
						

							
87
7. Appendix
Model Number NP600S/NP500WS
OpticalNP600SNP500WS
LCD Panel0.63 inch LCD with Micro Lens Array (Aspect Ratio 4:3)0.59 inch LCD with Micro Lens Array (Aspect Ratio 16:10)
Resolution1024  768 pixels*11280  800 pixels*1
LensFixed zoom and manual focus
Digital Zoom Ratio= 1.2F2.3  f= 9.7 mm
Lamp230W AC (170W in ECO Mode)
Light Output*2*32600 lumens (approx. 70% in ECO Mode)2100 lumens (approx. 70% in ECO Mode)
Contrast Ratio*3
(full white: full black)600:1
Image Size (Diagonal)60"–110"/ 1.52 m–2.79 m57"–104"/1.45 m–2.64 m 
Projection Distance35"–66"/ 0.9 m–1.7 m36"–66"/ 0.9 m–1.7 m
Projection Angle29.1°–29.4°
*1 Effective pixels are more than 99.99%.
*2  This  is  the  light  output  value  (lumens)  when  the  [PRESET]  mode  is  set  to  [HIGH-BRIGHT].  If  any 
other mode is selected as the [PRESET] mode, the light output value may drop slightly.
*3  Compliance with ISO21118-2005
Electrical
Inputs1 RGB/Component (D-Sub 15 P), 1 RGB (Digital/Analog, DVI-I 29 P, HDCP*4 supported), 1 S-Video (DIN 4 P), 1 Video (RCA), 1 (L/R) RCA Audio, 2 Stereo Mini Audio
Outputs1 RGB (D-Sub 15P), 1 Stereo Mini Audio
PC Control1 PC Control Port (D-Sub 9P)
Wired LAN PortRJ-45
External ControlRS232, IR, Wired LAN
Color Reproduction16.7 million colors simultaneously, Full color
Compatible Signals*5Analog: VGA/SVGA/XGA/WXGA/WXGA+/SXGA/SXGA+/UXGA 480i/480p/576i/576p/720p/1080iDigital: VGA/SVGA/XGA/WXGA/SXGA
Video BandwidthRGB: 80 MHz (Max.)
Horizontal Resolution540 TV lines: NTSC/NTSC4.43/PAL/PAL-M/PAL-N/PAL60300 TV lines: SECAM
Scan RateHorizontal: 15 kHz to 100 kHz (RGB: 24 kHz or over)Vertical: 50 Hz to 120 Hz
Sync CompatibilitySeparate Sync / Composite Sync / Sync on G
Built-in Speaker7W (monaural)
Power RequirementNP600S: 100–240V AC, 50/60HzNP600SG: 200–240V AC, 50/60HzNP500WS: 100–240V AC, 50/60HzNP500WSG: 200–240V AC, 50/60Hz
Input CurrentNP600S: 3.8–1.5ANP600SG: 1.8ANP500WS: 3.8–1.5ANP500WSG: 1.8A
Power Consumption325W  in  Lamp  NORMAL  Mode/240W  in  Lamp  ECO  Mode/11W  in  STANDBY  Mode/3W  in  POWER-SAVING Mode
*4 What is HDCP/HDCP technology?
  HDCP is an acronym for High-bandwidth Digital Content Protection. High bandwidth Digital Content 
Protection (HDCP) is a system for preventing illegal copying of video data sent over a Digital Visual Interface (DVI).
  If  you  are  unable  to  view  material  via  the  DVI  input,  this  does  not  necessarily  mean  the  projector 
is not functioning properly. With the implementation of HDCP, there may be cases in which certain content is protected with HDCP and might not be displayed due to the decision/intention of the HDCP community (Digital Content Protection, LLC).
*5  An image with higher or lower resolution than the projector’s native resolution (NP600S: 1024  768 / NP500WS: 1280  800) will be displayed with Advanced AccuBlend. 
						

							
88
7. Appendix
Mechanical
Installation OrientationDesktop/Front, Desktop/Rear, Ceiling/Front, Ceiling/Rear
Dimensions12.1"(W)  5.4"(H)  11.9"(D)/308 mm(W)  136 mm(H)  301 mm(D)(not including protrusions)
Weight7.28 lbs/3.3kg
Environmental ConsiderationsOperational Temperatures : 41° to 104°F (5° to 40°C), (ECO mode selected automatically at 95°F to 104°F/35°C to 40°\
C) 20% to 80% humidity (non-condensing) Storage Temperatures : 14° to 122°F (-10° to 50°C), 20% to 80% humidity (non-condensing)
RegulationsUL/C-UL Approved (UL 60950-1, CSA 60950-1)Meets DOC Canada Class B requirementsMeets FCC Class B requirementsMeets AS/NZS CISPR.22 Class BMeets EMC Directive (EN55022, EN55024, EN61000-3-2, EN61000-3-3)Meets Low Voltage Directive (EN60950-1, TÜV GS Approved)
For additional information visit:
US : http://www.necdisplay.com/
Europe : http://www.nec-display-solutions.com/
Global : http://www.nec-display.com/global/index.html
For information on our optional accessories, visit our website or see our brochure.
The specifications are subject to change without notice. 
						

							
89
7. Appendix
SELECT
MENU
EXITENTER
STATUSLAMPAUTO ADJ.SOURCE
FOCUS
263 (10.4
)
78 (3.1)
108.5 (4.3)
55.3 (2.2)
76 (3.0)308 (12.1)
 Cabinet Dimensions
NP600/NP500/NP400/NP00/NP500W
Lens center
Lens center
Unit: mm (inch) 
						

							
90
7. Appendix
NP600S/NP500WS
SELECT
MENU
EXITENTER
STATUSLAMP
AUTO ADJ.SOURCE
FOCUS
78 (3.1)
308 (12.1)
76 (3)
143.2 (5.6
)
301.5 (11.9
)
75.5 (3
)
Lens center
Lens center
Unit: mm (inch) 
						

							
9
7. Appendix
Mini D-Sub 15 Pin Connector
 Pin Assignments of D-Sub COMPUTER Input Connector
Signal Level
Video signal : 0.7Vp-p (Analog)
Sync signal : TTL level
51 42 31011121314156 97 8
 Pn No.   RGB Sgnal (Analog)  YCbCr Sgnal
  1  Red  Cr
  2  Green or Sync on Green  Y
  3  Blue  Cb
  4  Ground
  5  Ground
  6  Red Ground  Cr Ground
  7  Green Ground  Y Ground
  8  Blue Ground  Cb Ground
  9  No Connection
  10  Sync Signal Ground
  11  No Connection 
  12  Bi-directional DATA (SDA)
  13 
Horizontal Sync or Composite Sync
 14  Vertical Sync
  15  Data Clock