NEC Np60 Projector User Manual

23
Auto Keystone Correction
The Auto Keystone correction feature will correct the vertical distortion of a projected image on the screen. No 
special operation required. Just place the projector on a fl at surface.
3. Projecting an Image (Basic Operation)
NOTE: When using the Auto Keystone function, heed the following:The vertical keystone angle can be corrected between 16 degrees upward and 16 degrees downward from level.
 The Auto Keystone correction will take effect in 2 seconds after changing the...

24
SELECTSOURCEAUTO
ADJ.
ON/STAND BY FOCUSLAMP
STATUS
POWER
SOURCEAUTO
ADJ.
ON/STAND BY FOCUSLAMP
STATUS
POWER
SELECT
3. Projecting an Image (Basic Operation)
➍
 Adjusting Focus Manually
Adjust the focus manually in the following cases:
•  When adjusting the focus out of the effective range of the automatic focus
•  When fi nely adjusting the focus
•  When the menu setting for [Auto Focus] is turned off
Adjusting with buttons on the cabinet
1.  Press the FOCUS button quickly.
  The focus adjustment...

25
SELECTSOURCEAUTO
ADJ.
ON/STAND BY FOCUSLAMP
STATUS
POWER
➎
 Correcting Keystone Distortion Manually
You can also correct the vertical keystone distortion manually.
NOTE: Manual keystone correction is not available when there is no signal received by any input.
Adjust the keystone distortion manually in the following cases:
•  To fi ne tune Keystone correction even after performing the [Auto Keystone] adjustment
•  When the menu setting for [Auto Keystone] is turned off
Adjusting with buttons on the...

26
SELECTAUTO
ADJ.
ON/STAND BY FOCUSLAMP
STATUS
POWER
SOURCE
3. Projecting an Image (Basic Operation)
[Poor picture]
[Normal picture]
➏
 Optimizing RGB Picture Automatically
Adjusting the Image Using Auto Adjust
This adjustment may be necessary when you connect your computer for the fi rst time.
Adjusting with buttons on the cabinet
•  Press the SELECT  ◀ button with no menus displayed.
  An RGB image will be optimized automatically after a few seconds.
Adjusting with the remote control •  Press the...

27
AUTO
ADJ.
ON/STAND BY FOCUSLAMP
STATUS
POWER
SELECT
\f
 Turning off the Projector
To turn off the projector:
3. Projecting an Image (Basic Operation)
ENTEREXIT
MENU
UP
PAGE
OFF
POWER ON
PIC-MUTE
DOWN
FOCUSFirst, press the POWER (ON/STAND BY) button on the 
projector cabinet or the POWER OFF button on the re-
mote control. The “Power Off / Are you sure?” message 
will appear.
❽  After Use
Preparation: Make sure that the projector is turned off.
1.  Unplug the power cable.
2.  Disconnect any other...

28
4. Convenient Features
➊ Turning off the Image
Press the PIC-MUTE button to turn off the image for a short period of 
time. Press again to restore the image.
MENU UP
PAGE
OFF
POWER ON
PIC-MUTEDOWN
FOCUS
➋  Freezing a Picture
Press the FREEZE button to freeze a picture. Press again to resume 
motion.
➌ Changing Lamp Mode
LAMP MODE
VOLUMES-VIDEO
VIDEO
L-CLICK
MOUSE
R-CLICK
AUTO ADJ.
COMPUTER
ASPECT HELP
FREEZE
PICTURE
The lamp life can be extended by using the Eco mode.
To change to the “Eco” mode, do...

29
4. Convenient Features
3.  Select [On] and press the ENTER button.
  The [Security Keyword] screen will be displayed.
4.  Type in a combination of the four SELECT ▲▼◀ ▶ buttons and press the ENTER button.
NOTE: A keyword must be 4 to 10 digits in length.
  The [Confirm Keyword] screen will be displayed.
5.  Type in the same combination of SELECT  ▲▼◀ ▶ buttons and press the ENTER button. 
  The confirmation screen will be displayed.
6.  Select [Yes] and press the ENTER button. 
  The Security...

30
4. Convenient Features
To disable the Security function:
1.  Press the MENU button.
  The menu will be displayed.
2.  Select [Setup - Installation] → [Security] and press the ENTER button.
  The Off/On menu will be displayed.
3.  Select [Off] and press the ENTER button.
  The Keyword confirmation screen will be displayed.
4.  Type in your keyword and press the ENTER button. 
  When the correct keyword is entered, the Security function will be disabled.
NOTE: If you forget your keyword, contact your...

31
30°30°
4. Convenient Features
➎
 Using the Optional Remote Mouse Receiver (NP01MR)
The optional remote mouse receiver enables you to operate your computer’s mouse functions from the remote 
control. It is a great convenience for clicking through your computer-generated presentations.
Connecting the remote mouse receiver to your computer
If you wish to use the remote mouse function, connect the mouse receiver and computer.
The mouse receiver can be connected directly to the computer’s USB port (type...

32
4. Convenient Features
TIP: You can change the Pointer speed on the Mouse Properties dialog box on the Windows. For more information, see the user 
documentation or online help supplied with your computer.
About Drag Mode
By pressing the MOUSE L-CLICK or R-CLICK button for 2 or 3 seconds then releasing, the drag mode is set and 
the drag operation can be performed simply by pressing the SELECT  ▼▲◀ ▶ button. To drop the item, press the 
MOUSE L-CLICK (or R-CLICK) button. To cancel it, press the MOUSE...