NEC Np1250 Lcd Projector Users Manual


6. Using On-Screen Menu
Using Software Keyboard to enter an encryption key
1. Select one of [KEY 1], [KEY 2], [KEY 3] and [KEY 4] and press the ENTER button.
  The software keyboard will be displayed.
 
2. Use the SELECT  button to select one key and press the ENTER button.
3.  After finishing entering the WEP key, use the SELECT  button to select [OK] and press the EN-
TER button.
  The software keyboard will disappear.
When [WPA-PSK], [WPA-EAP], [WPA2-PSK] or [WPA2-EAP] is...

8
6. Using On-Screen Menu
[MAIL]
ALERT MAIL:
Checking this box enables Alert Mail feature.
This option notifies your computer of an error message via e-mail when using wireless or wired LAN. The error 
message will be notified when the projector lamp has reached the end of its usable life or an error occurs in the 
projector.
Sample of a message sent from the projector:
The lamp is at the end of its usable life. Please replace the lamp.
Projector Name: X X X X
Lamp Hours Used: xxxx [H]...

9
6. Using On-Screen Menu
Selecting Communication Speed [COMMUNICATION SPEED]
This feature sets the baud rate of the PC Control port (D-Sub 9 Pin). It supports data rates from 4800 to 38400 bps. 
The  default  is  38400  bps.  Select  the  appropriate  baud  rate  for  your  equipment  to  be  connected  (depending  on  the 
equipment, a lower baud rate may be recommended for long cable runs).
Your selected communication speed will not be affected even when [RESET] is done from the menu....

0
[ENTRY]
To assign your password:
NOTE: Up to 10 alphanumeric characters can be assigned.
1. Type a password.
  Select the [ENTER PASSWORD] entry box and press the ENTER button. (→ page 81)
 An asterisk will be displayed. 
 The  Software  keyboard  appears.  Use  the  Software  keyboard  to  type  a  password  on  the  [ENTER  PASS-
WORD] screen and press the ENTER button.
 The [CONFIRM PASSWORD] screen will be displayed.
2. Type the same password again and press the ENTER button.
  Your...


[SECURITY]
The Security function enables you to protect your projector so that the projector will not project a signal unless you 
enter a keyword. There is also an option to lock the projector by using a registered USB memory* as a protect key. 
Once you have registered your USB memory as a protect key, you are required to insert the registered USB mem-
ory  into  the  USB  port  of  the  projector  each  time  you  turn  on  the  projector. You  can  enable  the  Security  function  by...


To register a USB memory device as a protect key.
Preparation: Insert the USB memory device into the USB port (type A) of the projector.
1. Use the SELECT  or  button to select [USE PROTECT KEY] and press the ENTER button.
2.  Use the SELECT  or  button to select [READ] and press the ENTER button.
  Data of the USB memory will be read into the projector.
3. Use the SELECT  or  button to select [REGISTER] and press the ENTER button.
  Downloaded data will be registered and be...

3
• The  security  disable  mode  is  maintained  until  the  main  power  is  turned  off  (by  setting  the  main  power  switch 
to “O” or unplugging the power cord). In the following cases you will be asked to check the protect key or input 
the keyword:
(1) When [OK] is selected at an image for which security is set and the power is turned off then back on
(2) When the main power is turned off then back on while the security function is enabled
(3) When you attempt to display an image for...

4
Setting a Password for HTTP Server [HTTP SERVER]
This option allows you to assign a password when you use your HTTP server. A password must be between 1 and 
10 alphanumeric characters.
To set and delete a password, repeat steps described in [BACKGROUND LOCK]. 
Turning On or Off Remote Sensor [REMOTE SENSOR]
This option determines which remote sensor on the projector is enabled in wireless mode.
The options are: FRONT/BACK, FRONT, and BACK. 
6. Using On-Screen Menu 

5
Setting ID to the Projector [CONTROL ID]
NOTE: This function is available only when the optional remote control (NP02RC) is used. This function will not work with the re-
mote control included with the NP3250/NP2250/NP1250/NP3250W projector.
You  can  operate  multiple  projectors  separately  and  independently  with  the  same  single  remote  control.  To  do 
so,you have to assign an ID number to each projector....


6. Using On-Screen Menu
[OPTIONS]
Setting Auto Adjust [AUTO ADJUST]
This feature sets the Auto Adjust mode so that the RGB image can be automatically or manually adjusted for noise 
and stability. You can automatically make adjustment in two ways: [NORMAL] and [FINE].
OFF.........................The.RGB.image.will.not.be.automatically.adjusted.
You.can.manually.optimize.the.RGB.image....