NEC Np1200 Lcd Projector Users Manual

Selecting	Aspect	Ratio	[ASPECT	RATIO]
The	term	“aspect	ratio” 	refers	to	the	ratio	of	width	to	height	of	a	projected	image.
The	projector	automatically	determines	the	incoming	signal	and	displays	it	in	its	appropriate	aspect	ratio.
•	This	table	shows	typical	resolutions	and	aspect	ratios	that	most	computers	support.
ResolutionAspect	RatioVGA	 640	x	480	 4:3SVGA	 800	x	600	4:3XGA	 1024	x	768	4:3WXGA	 1280	x	768	 15:9WXGA	 1280	x	800	 16:10WXGA+	 1440	x	900	 16:10SXGA	 1280	x	1024	5:4SXGA+	 1400	x	1050...

Sample	image	when	the	appropriate	aspect	ratio	is	automatically	determined
[Computer	signal]
Aspect	ratio	of	incoming	signal4:35:416:915:916:10
Sample	image	when	the	appro-priate	aspect	ratio	is	automati-cally	determined
[Video	signal]
Aspect	ratio	of	incoming	signal4:3LetterboxSqueeze
Sample	image	when	the	aspect	ratio	is	automatically	deter-minedNOTE:	To	display	a	squeezed	signal	prop-erly,	select	[16:9]	or	[WIDE	ZOOM].
TIP:
•	 Image	position	can	be	adjusted	vertically	using	[POSITION]	when	the	[16:9],...

[AUDIO]
Controlling	Sound	[VOLUME/BASS/TREBLE/BALANCE]
Adjusts	the	volume,	 bass	and	treble	 level,	left	and	 right	 balance	 of	the	 projector	 speaker	and	AUDIO	 OUT	(Stereo	
Mini	Jack).
TIP: 
[VOLUME]
•	 When	 no	menus	 appear,	 the	 and 	buttons	 on	the	 projector	 cabinet	and	the	VOL.	 +/−	buttons	 work	as	a	volume	 control.	 (→ 
page 30)
[BALANCE]
•	 When	the 	left/monaural 	of 	the 	video/component 	audio 	input 	is 	connected, 	the 	right 	and 	left 	channel 	sound 	from 	the 	AUDIO 	OUT...

 Menu Descriptions & Functions [SETUP]
[GENERAL]
Correcting	Vertical	Keystone	Distortion	Manually	[KEYSTONE]
You	can	correct	vertical	distortion	manually. 	(→	page	28)
TIP: When this option is highlighted, pressing the ENTER button will dis\
play its slide bar for adjustment.
Saving	Vertical	Keystone	Correction	[KEYSTONE	SAVE]
This	option	enables	you	to	save	your	current	keystone	settings.
OFF ������������������������Does  not  save  current  keystone  correction  settings �  It  will  return  your...

Using	the	Wall	Color	Correction	[WALL	COLOR]
 
This	function	allows	for	quick	adaptive	color	correction	in	applications	where	the	screen	material	is	not	white.
NOTE:	Selecting	[WHITEBOARD]	reduces	lamp	brightness.
Setting	Eco	Mode	[ECO	MODE]
This	feature	turns	on	or	off	the	ECO	mode. 	The	lamp	life	can	be	extended	by	selecting	[ON]. 	Selecting	[ON]	also	de-
creases	fan	noise	when	compared	to	[OFF]	mode. 	(→	page	33)
ECO	MODEDescriptionStatus	of	LAMP	indicator
OFFThis	is	the	Default	setting
(100%...

Setting	Closed	Caption	[CLOSED	CAPTION]
This	option	 sets	several	 closed	caption	 modes	that	allow	 text	to	be	 superimposed	 on	the	 projected	 image	of	Video	
or	S-Video.
OFF ������������������������This exits the closed caption mode�
CAPTION 1-4 ���������Text is superimposed�
TEXT 1-4 ����������������Text is displayed�
NOTE:
•	 The	closed	caption	is	not	available	under	the	following	conditions:
-  when messages or menus are displayed.
- when an image is magnified, frozen, or muted.
Selecting	Menu...

Turning	On	/	Off	Eco	Message	[ECO	MESSAGE]
This	option	turns	on	or	off	the	following	messages	when	the	projector	is	turned	on.	
The	Eco	Message	 prompts	the	user	 to	save	 energy. 	When	 [OFF]	is	selected	 for	[ECO	 MODE],	 you	will	get	 a	mes-
sage	to	prompt	you	to	select	[ON]	for	[ECO	MODE].
When	[ON]	is	selected	for	[ECO	MODE]
To	 close	 the	message,	 press	any	one	 of	the	 buttons. 	The	 message	 will	disappear	 if	no	 button	 operation	 is	done	 for	
30 seconds.
When	[OFF]	is	selected	for	[ECO...

[INSTALLATION]
Selecting	Projector	Orientation	[ORIENTATION]
This	reorients	 your	image	 for	your	 type	of	projection. 	The	 options	 are:	desktop	 front	projection,	 ceiling	rear	projec-
tion,	desktop	rear	projection,	and	ceiling	front	projection.
DESKTOP	FRONTCEILING	REAR
DESKTOP	REARCEILING	FRONT
Disabling	the	Cabinet	Buttons	[CONTROL	PANEL	LOCK]
This	option	turns	on	or	off	the	CONTROL	PANEL	LOCK	function.
NOTE:
•	 This	CONTROL	PANEL	LOCK	does	not	affect	the	remote	control	functions.
•	 When	 the...

Selecting	Communication	Speed	[COMMUNICATION	SPEED]
This	feature	 sets	the	baud	 rate	of	the	 PC	Control	 port	(D-Sub	 9P).	It	 supports	 data	rates	 from	4800	 to	19200	 bps.	
The	 default	 is	19200	 bps.	Select	 the	appropriate	 baud	rate	for	your	 equipment	 to	be	 connected	 (depending	 on	the	
equipment,	a	lower	baud	rate	may	be	recommended	for	long	cable	runs).
NOTE: Your selected communication speed will not be affected even when [RESET] is done from the menu.
Turning	On	or	Off	Remote	Sensor...

4. Release the ID SET button.
	 The	updated	CONTROL	ID	screen	will	be	displayed.
NOTE:
•	 The	IDs	can	be	cleared	in	a	few	days	after	the	batteries	are	run	down	or	removed.
•	 Accidentally	pressing	any	one	of	the	buttons	of	the	remote	control	will	clear	currently	specified	ID	with	batteries	removed.
69
5. Using On-Screen Menu