NEC Neax 2400 Ipx Circuit Card System Manual

CHAPTER 3 NDA-24318
Page 24
Issue 1
OFFICE DATA PROGRAMMING
11. This feature does not support Broad Band Services H0/H1. Therefore, when assigning the IPTRK circuit
card routes by the ARTD command, enter BOB = 0.
12. This feature can use link re-connection function. Service conditions are the same as those for the normal
CCIS network.
13. PAD can be provided for RECEIVE control only.
14. On a conference call via IPTRK, Echo Canceller cannot be activated when using certain kinds of telephone
sets...

NDA-24318 CHAPTER 3
Page 25
Issue 1
OFFICE DATA PROGRAMMING
Figure 3-3   Port Assignment of Bch for CCIS Tie Line
Note 1:
An IPTRK circuit card can be accommodated in the shaded slots (a maximum of two cards per UNIT). HW
indicates Highway Block.
Note 2:This example represents the port allocation when sub board PZ-8VCTB is mounted.
Note 3:Be sure to assign a B-channel in the first time slot of the controlling IPTRK circuit card.
CCIS signal controlling channel is determined in accordance with the CIC...

CHAPTER 3 NDA-24318
Page 26
Issue 1
OFFICE DATA PROGRAMMING
Perform the following data assignment using the ACSC/ACIC2 commands.
Figure 3-4   Example Data Assignment (ACSC/ACIC2) CCIS - CCIS Networking via IP [C-163]
Note:
This data setting is an example.
PC=1PC=2CCT IPTRKCCT IPTRK
CCIS CCIS Networking via IP
 
CSCGCICGCCHMG U G
00-07 0-3 00-23
11 0 000
21 000
31 000
41
1
1
1
1 00026 00
26
600
26 00
22
2
2
2
6 00
       130 
(Basic/Primary 
Route)
5
7
ACSC
slot 10
PWR
00
0102
0304
0506 0708 0912 13 14...

NDA-24318 CHAPTER 3
Page 27
Issue 1
OFFICE DATA PROGRAMMING
In Point-to-Multipoint connection, because it cannot be determined which destination node is to be
called until the call is originated, all of the CCIS related data is assigned for the self-node. As to the
ACIC1 command, the data must be assigned to all the destination nodes and also to the self-node.
Designate the Speech Path and Point Code to the assigned Outgoing Route Selection Pattern
number by using the AOPRL/AOPRN command (this is...

CHAPTER 3 NDA-24318
Page 28
Issue 1
OFFICE DATA PROGRAMMING
Figure 3-5   Example Assignment of IP Addresses of IPTRK Circuit Card and Connected Router
IPTRK
bbb.bbb.bbb.b
IPTRK
aaa.aaa.aaa.a
POWERPOWER
(
1) 
To 
No
de 
B(
2) T
o N
od
e 
C
(1) (2)
PO WER
IPTRK
ccc.ccc.ccc.c
IPTRK
ddd.ddd.ddd.d
PWR
00
0102
0308 0910 1112 13 14 1516 17 18 1920 21 22 2300 0102 03
slot 06/07
070504 06 IPTK_IP   aaa.aaa.aaa.a 
 DG_IP   xxx.xxx.xxx.x 
 MULT   Point-to-Multipoint 
 DST_IP   ccc.ccc.ccc.c
04 0506 07 09...

NDA-24318 CHAPTER 3
Page 29
Issue 1
OFFICE DATA PROGRAMMING
3. FCCS NETWORKING VIA IP [F-36]
This feature allows the system to exchange both speech and FCCS signals via the Intranet. It is not necessary to
use an FCH circuit card. To establish/release a call, the following connection patterns can be selected:
For both speech and FCCS signal channels, an IPTRK circuit card is used. At this time, the IPTRK circuit cards
in the self-node and each of its connected node(s) must be in 1-to-1 ratio. See Section...

CHAPTER 3 NDA-24318
Page 30
Issue 1
OFFICE DATA PROGRAMMING
3.1 Required Hardware
This feature is available by using the following hardware. As shown, both speech and FCCS signal
channels between the nodes must be provided by IPTRK circuit cards with 10 BASE-T cables.
Figure 3-7   Example Required Hardware for FCCS Networking via IP [F-36]
Note:
An IPTRK circuit card, assigned as the FCCS signal control card by the AFCH command, can also control
the B-channels of the same card, and also a maximum of 15...

NDA-24318 CHAPTER 3
Page 31
Issue 1
OFFICE DATA PROGRAMMING
3.2 Required Hardware (Point-to-Multipoint Connection)
This feature (allowing IPTRK circuit card for both speech and FCCS signal channels) is available by using
the following hardware. Once this feature is set, each IPTRK circuit card can make a Point-to-Multipoint
Connection with IPTRK circuit cards of multiple nodes.
Figure 3-8   Example Required Hardware for FCCS Networking via IP [F-36] [IPTRK: Point-to-Multipoint]
Note:
An IPTRK circuit...

CHAPTER 3 NDA-24318
Page 32
Issue 1
OFFICE DATA PROGRAMMING
3.3 Service Conditions
1. To send/receive voice information, each node will use an IPTRK circuit card. At this time, the IPTRK
circuit cards in the self-node and its connected node(s) can be either in 1-to-1 ratio, respectively, or in 1-
to-n (n=2 or more) relations (referred to as Point-to-Multipoint connection). 
2. Be sure to use a router for connections between IP network and IPTRK circuit card.
3. A maximum of two IPTRK circuit cards per...

NDA-24318 CHAPTER 3
Page 33
Issue 1
OFFICE DATA PROGRAMMING
7. For Point-to-Multipoint connection, one IPTRK circuit card (assigned as FCCS signal controlling card by
the AFCH command), can control the B-channels of the same card, and also a maximum of 15 other
IPTRK circuit cards. It is not necessary to assign the trunk data for a time slot as a controlling channel.See
the following figure.
Note 1:The IPTRK circuit card can be accommodated in the shaded slots (a maximum of two cards per UNIT).
HW...