NEC Neax 2400 Imx Wireless System Manual

CHAPTER 1 ND-70290 (E)
Pag e 4
Revision 3.0
GENERAL DESCRIPTION
3. MOVEMENT OF PS IN NEAX2400 IMX
PCS COMMUNITY
The SYS-ID is a unique ID which was given to manage the PCS system. The area where the SYS-ID is effective
is called PCS Community. Every PCS Community in a Fusion network is given a unique PHS Community
Number (PCN). Each PCN has its own SYS-ID. The PCN is used in stead of the SYS-ID for MAT command,
and this can reduce the effect upon changing the SYS-ID to some measure. The habitual...

ND-70290 (E) CHAPTER 1
Page 5
Revision 3.0
GENERAL DESCRIPTION
Fusion-I
A
B
C
D
Home PCN-a
Home
 PCN-b
Fusion-II
EF Visit PCN-c
        Visit
 PCN-d
G
 Node-WNode-XNode-YNode-Z
FCCS
Q. 931a or IS-11572 Note 
FCCS
Note:Node-W and Node-Y are connected with Q. 931a or IS-11572.
A, B
Home Node
Home PCNC, D
Visit Node
Home PCNE
Visit Fusion
Visit Node
Visit PCNF
Visit Fusion
Other Node
Visit PCNG
Ye t  O t h e r
Fusion
A, B
Home Node
Home PCNStand-by condition 
Movement
H-OStand-by condition 
Movement...

CHAPTER 1 ND-70290 (E)
Pag e 6
Revision 3.0
GENERAL DESCRIPTION
4. SYSTEM CAPACITY
The following explains the capacity of the System.
Note 1:Depending on capacity of NDM/LDM.
When upgrading from ICS and re-using Data Memory, Maximum 2000 terminals/Node.
Note 2:A maximum of 12 circuit cards can be mounted in a PIM.
5. MOUNTING LOCATION OF CSINT CIRCUIT CARD
CSINT circuit card can be mounted in any universal slot in the PIM.
Table 1-1  System Capacity
ITEMS 1-IMG System 4-IMG System
IMX-U System
Max....

ND-70290 (E) CHAPTER 1
Page 7
Revision 3.0
GENERAL DESCRIPTION
6. FUNCTIONS/MOUNTING CONDITIONS OF CIRCUIT CARDS
The following circuit cards are necessary when using the system.
1. Universal LC/TRK circuit cards
ABBREVIATIONCIRCUIT 
CARD NAMEFUNCTIONS AND MOUNTING CONDITIONS
RST PA-8RSTJ/
PA - 8 R S T MRegister-Sender 
As is the case with the RST functions in the normal stations, the RST is used 
virtually, and estimating how many lines are needed is as important as 
considering the number of terminals....

CHAPTER 1 ND-70290 (E)
Pag e 8
Revision 3.0
GENERAL DESCRIPTION
CLK PH-CK18
(IMX-U
System)This card is used for the Local Node of the IMX-U system. This card receives 
clock signals from the Phase Lock Oscillator (PLO) accommodated in 
TSWM0 of IMG1, distributing the following signals to Time Division 
Switch (TSW) accommodated in TSWM1 of IMG2.
 32.768 MHz CLK
 8 KHz FH
5 msec × “n” FH
CSINT PA-4CSIC This is an LC circuit card which provides interface with the Zone Transceiver 
(ZT). A maximum of...

ND-70290 (E) CHAPTER 1
Page 9
Revision 3.0
GENERAL DESCRIPTION
7. SERVICE CONDITIONS
Below are some of the conditions for using the System.
1. The system is available in the Business/Hotel System.
2. ACD/OAI services are incompatible with the system.
3. The following software is necessary for system operation.
Basic software: Series 7300 or later
Optional software: Service (Application) software including PCS service.  
Note 
Note:
When using PCS in Fusion Network, this software must  be installed in all...

CHAPTER 1 ND-70290 (E)
Pag e 1 0
Revision 3.0
GENERAL DESCRIPTION
8. LIST OF SERVICE FEATURES
1. PCS Feature
Table 1-2  List of PCS Features
SERVICE FUNCTIONS REMARKS
UNUSED NUMBER
PS LOCATION 
REGISTRATION
OG CALL TO OUTSIDE Least Cost Routing (LCR) is the only dialing method valid in OG call to 
outside.
Note 1:For Fusion Network, this feature is available for Release 3 or
later software.
INDIVIDUAL PS CALLING Incoming calls can be terminated to a PS only in the area where the 
corresponding PS is...

ND-70290 (E) CHAPTER 1
Page 11
Revision 3.0
GENERAL DESCRIPTION
Note 3:
Handover
1) If a PS user moves to another zone that has all speech channels busy, the PS remains connected to the
original ZT.
2) Speech is temporarily interrupted during handover.
3) PS is unable to hand over in the following cases:
• When digits are being sent (BT is heard.)
 When a PS user attempts to hand over  while connected to  an operator (Attendant Console). BT is
heard.
 When user C who has set Call Waiting to user A...

CHAPTER 1 ND-70290 (E)
Pag e 1 2
Revision 3.0
GENERAL DESCRIPTION
Table 1-3  List of OG Call Features
×: Available : Conditionally available –: Not available/Not used
NAME OF SERVICE FEATURESStandalone Fusion
REMARKS
From PS To PS From PS To PS
ALTERNATE ROUTING/ROUTE 
ADVANCE×–––
SPEED CALLING-STATION/
GROUP––––To be substituted for the memory 
dial of PS
SPEED CALLING-SYSTEM – – – –
TOLL CALL RESTRICTION×–––
PUSH-BUTTON TO ROTARY 
CONVERSION––––
PRIMARY CODE RESTRICTION×–––
OG TRUNK QUEUING – – – –
OFF...

ND-70290 (E) CHAPTER 1
Page 13
Revision 3.0
GENERAL DESCRIPTION
Note 1:
When a  PS is assigned as the target station of DIRECT IN TERMINATION (DIT).
1) When the PS is Out of Zone (Out of Zone or in a state of POWER OFF), RBT is heard by the calling
party.
If AUTOMATIC ANNOUNCEMENT-PS OUT OF ZONE is assigned by the PS, the calling party does
not hear the Out of Zone Announcement, and instead hears RBT.
2) If a PS user moves Out of Zone while connected to an outside party, AUTOMATIC ANNOUNCEMENT-...