NEC Neax 2400 Imx Isdn Features And Specifications

NEAX2400 IMX ISDN Features and Specifications
NDA-24281, Issue 1
Page 175
Event Based CCIS - ISDN Transport E-23
Service Conditions (cont’d)
10. The following are the conditions of E-CCIS setup, Release Timer setting and E-CCIS release:
a.) Conditions of E-CCIS setup:
 If no voice channels are set up when a call occurs, a voice channel and the signal channel are
set up at the same time.
 If the signal channel is set up and no voice channels are released (Release Timer is being
activated), or if the...

NEAX2400 IMX ISDN Features and Specifications
Page 176NDA-24281, Issue 1
E-23 Event Based CCIS - ISDN Transport
Service Conditions (cont’d)
18. If line failure occurs, the alternate route is used when system message is received from ISDN network,
according to priority.
The alternate route can be used when the call is:
a.) originated from a station.
b.) originated from a station while holding a station call.
c.) originated from a station while holding a trunk call.
d.) originated using Tandem connection....

NEAX2400 IMX ISDN Features and Specifications
NDA-24281, Issue 1
Page 177
Event Based CCIS - ISDN Transport E-23
Service Conditions (cont’d)
DATA COMMUNICATION - CCIS  [D-41]
DATA INTERFACE - AUTOMATIC ANSWER - CCIS  [D-65]
DATA LINE SECURITY - CCIS  [D-66]
DATA LINE PRIVACY - CCIS [D-67]
DATA PRIVACY ON DEMAND - CCIS  [D-68]
DATA TRANSPARENCY - CCIS  [D-69]
DELUXE TRAVELING CLASS MARK - CCIS  [D-70]
DIAL ACCESS TO ATTENDANT - CCIS  [D-71]
DIGITAL DISPLAY - STATION - CCIS  [D-72]
DIGITAL DISPLAY - TRUNK...

NEAX2400 IMX ISDN Features and Specifications
Page 178NDA-24281, Issue 1
E-23 Event Based CCIS - ISDN Transport
Service Conditions (cont’d)
OFF-HOOK QUEUING - CCIS  [O-11]
OUTGOING TRUNK QUEUING - CCIS  [O-12]
PAGING ACCESS - CCIS  [P-28]
RESTRICTION FROM OUTGOING CALLS - CCIS  [R-22]
SERIAL CALL - CCIS  [S-52]
SERVICE DISPLAY - D
term - CCIS  [S-53D]
SIMULTANEOUS VOICE AND DATA TRANSMISSION - CCIS  [S-54]
SINGLE-DIGIT STATION CALLING - CCIS  [S-55]
STATION CONTROLLED CONFERENCE - CCIS  [S-56]...

NEAX2400 IMX ISDN Features and Specifications
NDA-24281, Issue 1
Page 179
Event Based CCIS - Q-SIG Transport E-24
E-24  Event Based CCIS - Q-SIG Transport
General Description
This feature provides VIRTUAL TIE LINE for each event such as call origination and MCI message transmission.
Inter-PBX link for this feature is established on B-channels of the private ISDN line using CCIS No. 7 signaling
protocol. For addressing a specific terminal, Called Sub Address or Called DID Number is used depending on the...

NEAX2400 IMX ISDN Features and Specifications
Page 180NDA-24281, Issue 1
E-24 Event Based CCIS - Q-SIG Transport
Service Conditions (cont’d)
13. The following features are available for the E-CCIS line:
ASYNCHRONOUS DATA SWITCHING - CCIS  [A-44] Note
ATTENDANT CAMP-ON WITH TONE INDICATION - CCIS [A-45]
ATTENDANT-CONTROLLED CONFERENCE - CCIS [A-46]
AUTOMATIC RECALL - CCIS [A-71]
AUTOMATIC NUMBER IDENTIFICATION (ANI) - CCIS [A-87]
BUSY VERIFICATION - CCIS [B-9]
BROKERAGE HOTLINE - CCIS [B-10]
CALL BACK -...

NEAX2400 IMX ISDN Features and Specifications
NDA-24281, Issue 1
Page 181
Event Based CCIS - Q-SIG Transport E-24
Service Conditions (cont’d)
HOUSE PHONE - CCIS [H-11]
HOTLINE - CCIS [H-12]
INCOMING CALL IDENTIFICATION  - CCIS [I-16]
INDIVIDUAL ATTENDANT ACCESS - CCIS [I-17]
INTER-POSITION TRANSFER - CCIS [I-18]
INDIVIDUAL TRUNK ACCESS - CCIS [I-19]
LOOK AHEAD ROUTING - CCIS [L-25]
LDN NIGHT CONNECTION - CCIS [L-29]
MESSAGE REMINDER - CCIS [M-34]
MESSAGE REMINDER - D
term - CCIS [M-34D]
MESSAGE WAITING...

NEAX2400 IMX ISDN Features and Specifications
Page 182NDA-24281, Issue 1
I-28 ISDN Individual Calling Line Identification (ICLID)
I-28 ISDN Individual Calling Line Identification (ICLID)
General Description
The ICLID feature is used to deliver a calling-partys number through the public ISDN network to a called-party in
the same PBX.
There are two types of calling party numbers; Automatic Number Identification (ANI), used for accounting; and
Station Identification (SID).
Operating Procedure
No manual...

NEAX2400 IMX ISDN Features and Specifications
NDA-24281, Issue 1
Page 183
Megacom Access M-76
M-76 Megacom Access
General Description
AT&T’s MEGACOM (WATS) network can be used.
Megacom Access Connection
Operating Procedure
No manual operation is required.
Service Conditions
The available WATS service is limited to Maximal Subscribed WATS Band (MSB).
Note:The parameter band service where zone is specified on a call-by-call basis is provided by the #5ESS only.
2400
IMX#4ESS
PRIMEGACOM 

NEAX2400 IMX ISDN Features and Specifications
Page 184NDA-24281, Issue 1
M-77 Megacom 800 Service
M-77 Megacom 800 Service
General Description
AT&T’s MEGACOM 800 (INWARD WATS) network can be used.
Megacom 800 Service Connection
Operating Procedure
No manual operation is required.
Service Conditions
1. When a call has terminated by the CALL-BY-CALL SERVICE SELECTION [C-105], no indication to
distinguish it from a call termination by other services is made to a terminating terminal.
2. To identify a...