NEC Neax 2400 Imx Isdn Features And Specifications

							NEAX2400 IMX ISDN Features and Specifications
NDA-24281, Issue 1
Page 175
Event Based CCIS - ISDN Transport E-23
Service Conditions (cont’d)
10. The following are the conditions of E-CCIS setup, Release Timer setting and E-CCIS release:
a.) Conditions of E-CCIS setup:
 If no voice channels are set up when a call occurs, a voice channel and the signal channel are
set up at the same time.
 If the signal channel is set up and no voice channels are released (Release Timer is being
activated), or if the signal channel is set up and no voice channels are set up, a voice channel is
set up when a call occurs.
 If no channels are set up when the signal controlled by the signal channel only (MCI, MW lamp
control, etc.) occurs, the signal channel is set up.
b.) Conditions of Release Timer setting:
 When the signal controlled by the signal channel only is transmitted or received, Release Timer
of the signal channel is activated.
 At the time of call completion, Release Timer of a voice channel is activated.
c.) Conditions of E-CCIS release:
 If all the voice channels but one are released and Release Timer of the signal channel has not
been set, the established voice channel and the signal channel are released at the same time
when Release Timer of the voice channel expires (at the time of call completion, if Release
Timer is set at immediately after call completion).
 When Release Timer of a voice channel expires, and if another voice channel or the other voice
channels are setup, that voice channel is released.
If all the voice channels but one are released, and when Release Timer of the established voice
channel expires while Release Timer of the signal channel is being activated, the voice channel
is released.
 If Release Timer of the signal channel expires when no voice channels are set up, the signal
channel is released.
 If Release Timer of the signal channel expires (Release Timer has not been assigned.) when one
or more voice channels are set up, no channels are released.
11. If all the E-CCIS routes are used, the connection can be established using the alternate route.
12. When the connection is not established due to line failure, etc., system message is output.
13. Bearer capability for voice channels of the E-CCIS line can be selected on a route basis, unrestricted digital
or speech. However, Bearer capability for a signal channel is unrestricted digital only.
14. If speech is selected for bearer capability for a signal channel of the E-CCIS line, data communication
using that E-CCIS route is restricted.
15. When the signal channel of the E-CCIS line is set up, the message control signal (such as the MCI
message) is sent to an E-CCIS route immediately. If not, the signal channel of the E-CCIS line is set up,
and then the message control signal is transmitted.
16. If patrol operation is performed for the E-CCIS turn, that E-CCIS line should be in the status of Release
Timer time out.
17. A trunk used at the time of call origination is selected from the trunk which has been set up for the E-CCIS
line. If two or more trunks have been set up, a trunk is selected by Trunk Route Data. 
						

							NEAX2400 IMX ISDN Features and Specifications
Page 176NDA-24281, Issue 1
E-23 Event Based CCIS - ISDN Transport
Service Conditions (cont’d)
18. If line failure occurs, the alternate route is used when system message is received from ISDN network,
according to priority.
The alternate route can be used when the call is:
a.) originated from a station.
b.) originated from a station while holding a station call.
c.) originated from a station while holding a trunk call.
d.) originated using Tandem connection.
e.) originated from an Attendant.
f.) originated from an Attendant while holding a station call.
g.) originated from an Attendant while holding a trunk call.
The alternate route cannot be used when the call is:
a.) originated from an ISDN terminal or a PS terminal.
b.) a data call.
c.) originated from an MFC trunk using Tandem connection.
If no alternate route is assigned, all the outgoing routes are busy.
When the alternate route is used, the following services cannot be used:
OFF-HOOK QUEUING  [O-7]
OUTGOING TRUNK QUEUING [O-2]
INTER-OFFICE OFF-HOOK QUEUING  [I-11]
ROUTE RESTRICTION - ANNOUNCEMENT  [R-27]
OUTGOING TRUNK BUSY - ANNOUNCEMENT  [O-21]
Dialing of AUTHORIZATION CODE [A-20] in case of the 
Tandem connection via the ISDN trunk.
19. The following features are available for the E-CCIS line:
ATTENDANT CAMP-ON WITH TONE INDICATION - CCIS [A-45]
ATTENDANT-CONTROLLED CONFERENCE - CCIS [A-46]
AUTOMATIC RECALL - CCIS  [A-71]
AUTOMATIC NUMBER IDENTIFICATION (ANI) - CCIS  [A-87]
BUSY VERIFICATION - CCIS  [B-9]
BROKERAGE HOTLINE - CCIS  [B-10]
CALL BACK - CCIS  [C-44]
CALL FORWARDING - ALL CALLS - CCIS [C-45]
CALL FORWARDING - BUSY LINE - CCIS  [C46]
CALL FORWARDING - DON’T ANSWER - CCIS  [C47]
CALL FORWARDING - INTERCEPT  [C-48]
CALL FORWARDING - OVERRIDE - CCIS  [C-49]
CALL TRANSFER - ALL CALLS - CCIS  [C-50]
CALLED STATION STATUS DISPLAY - CCIS [C-51]
CALLING/CALLED NUMBER DISPLAY - CCIS  [C-52]
CALL PROCESSING INDICATION - CCIS  [C-53]
CALL TRANSFER - ATTENDANT - CCIS  [C-54]
CONSULTATION HOLD - ALL CALLS - CCIS  [C-58]
CALL FORWARDING ASSIGNMENT - ATTENDANT - CCIS  [C-94] 
						

							NEAX2400 IMX ISDN Features and Specifications
NDA-24281, Issue 1
Page 177
Event Based CCIS - ISDN Transport E-23
Service Conditions (cont’d)
DATA COMMUNICATION - CCIS  [D-41]
DATA INTERFACE - AUTOMATIC ANSWER - CCIS  [D-65]
DATA LINE SECURITY - CCIS  [D-66]
DATA LINE PRIVACY - CCIS [D-67]
DATA PRIVACY ON DEMAND - CCIS  [D-68]
DATA TRANSPARENCY - CCIS  [D-69]
DELUXE TRAVELING CLASS MARK - CCIS  [D-70]
DIAL ACCESS TO ATTENDANT - CCIS  [D-71]
DIGITAL DISPLAY - STATION - CCIS  [D-72]
DIGITAL DISPLAY - TRUNK - CCIS  [D-73]
DIRECT-IN TERMINATION - CCIS  [D-74]
DISTINCTIVE RINGING - CCIS  [D-75]
DO NOT DISTURB - D
term - CCIS  [D-76D]
DIALED NUMBER DISPLAY - RECALL - CCIS  [D-91]
DUAL HOLD D
term - CCIS  [D-93D]
EXECTIVE RIGHT-OF-WAY - CCIS  [E-8]
ELAPSED TIME DISPLAY - CCIS  [E-9]
E-911 ANI UNIFIED NUMBER OF DIGITS - CCIS  [E-20]
FLEXIBLE NUMBERING OF STATIONS - CCIS  [F-12]
HANDS-FREE ANSWERBACK -D
term - CCIS  [H-10D]
HOUSE PHONE - CCIS  [H-11]
HOTLINE - CCIS  [H-12]
INCOMING CALL IDENTIFICATION - CCIS  [I-16]
INDIVIDUAL ATTENDANT ACCESS - CCIS  [I-17]
INTER-POSITION TRANSFER - CCIS  [I-18]
INDIVIDUAL TRUNK ACCESS - CCIS  [I-19]
LOOK AHEAD ROUTING - CCIS  [L-25]
LDN NIGHT CONNECTION - CCIS  [L-29]
MESSAGE REMINDER - CCIS  [M-34]
MESSAGE REMINDER - D
term - CCIS  [M-34D]
MESSAGE WAITING LAMP SETTING - ATTENDANT - CCIS  [M-35]
MESSAGE WAITING LAMP SETTING - STATION - CCIS  [M-36]
MISCELLANEOUS TRUNK ACCESS - CCIS  [M-37]
MISCELLANEOUS TRUNK RESTRICTION - CCIS  [M-38]
MULTIPLE CALL FORWARDING - ALL CALLS - CCIS  [M-40]
MULTIPLE CALL FORWARDING - BUSY LINE - CCIS  [M-41]
MULTIPLE CALL FORWARDING - DONT ANSWER - CCIS  [M-42]
MULTIPLE CONSOLE OPERATION - CCIS  [M-43]
MESSAGE CENTER INTERFACE - CCIS [M-67] 
NIGHT CONNECTION - FIXED - CCIS  [N-15]
NIGHT CONNECTION - FLEXIBLE - CCIS  [N-16]
NAME DISPLAY - SYSTEM - CCIS  [N-37] 
						

							NEAX2400 IMX ISDN Features and Specifications
Page 178NDA-24281, Issue 1
E-23 Event Based CCIS - ISDN Transport
Service Conditions (cont’d)
OFF-HOOK QUEUING - CCIS  [O-11]
OUTGOING TRUNK QUEUING - CCIS  [O-12]
PAGING ACCESS - CCIS  [P-28]
RESTRICTION FROM OUTGOING CALLS - CCIS  [R-22]
SERIAL CALL - CCIS  [S-52]
SERVICE DISPLAY - D
term - CCIS  [S-53D]
SIMULTANEOUS VOICE AND DATA TRANSMISSION - CCIS  [S-54]
SINGLE-DIGIT STATION CALLING - CCIS  [S-55]
STATION CONTROLLED CONFERENCE - CCIS  [S-56]
STATION-TO-STATION CALLING - CCIS  [S-57]
STATION-TO-STATION CALLING - OPERATOR ASSISTANCE - CCIS [S-58]
STEP CALL - CCIS  [S-59]
SYNCHRONOUS DATA SWITCHING - CCIS  [S-60]
SUPERVISORY CALL - CCIS  [S-73]
TOLL RESTRICTION - 3/6-DIGIT - CCIS  [T-26]
TRUNK ANSWER FROM ANY STATION - CCIS -  [T-27]
UNIFORM NUMBERING PLAN - CCIS  [U-5]
VOICE CALL - CCIS  [V-7]
20. The following features are available only when the attribute data of ISDN calls for the E-CCIS line is
assigned for data calls:
ASYNCHRONOUS DATA SWITCHING  [A-44]
DATA COMMUNICATION  [D-41]
DATA INTERFACE - AUTOMATIC ANSWER  [D-65]
DATA LINE SECURITY  [D-66]
DATA LINE PRIVACY  [D-67]
DATA PRIVACY ON DEMAND  [D-68]
DATA TRANSPARENCY  [D-69]
DATA HOTLINE - CCIS  [D-86]
MODEM POOLING - CCIS  [M-39]
21. The following features are available only when the signal-channel link of the E-CCIS line is established:
CENTRALIZED BILLING - CCIS  [C-55]
CENTRALIZED SYSTEM MANAGEMENT REPORT - CCIS [C-57] 
						

							NEAX2400 IMX ISDN Features and Specifications
NDA-24281, Issue 1
Page 179
Event Based CCIS - Q-SIG Transport E-24
E-24  Event Based CCIS - Q-SIG Transport
General Description
This feature provides VIRTUAL TIE LINE for each event such as call origination and MCI message transmission.
Inter-PBX link for this feature is established on B-channels of the private ISDN line using CCIS No. 7 signaling
protocol. For addressing a specific terminal, Called Sub Address or Called DID Number is used depending on the
network configuration.
Operating Procedure
No manual operation is required.
Service Conditions
1. The ISDN Primary Rate Interface (PRI) trunk is used for this feature.
2. The ETS 300 172 or ISO/IEC 11572 is available as ISDN interface for this service.
3. E-CCIS signal channel assignment is not necessary when activating via the private ISDN line because
E-CCIS line is controlled by the D-channel of ISDN.
4. This feature is activated between two PBXs directly connected each other. Therefore, this feature is not
available for the tandem office.
5. Since this feature uses the B-channel for ISDN as the speech line, the speech line is not established when
all B-channels are busy.
6. When using Called Sub Address as addressing information:
a.) Sub Address - Addressing must be available in the ISDN network.
b.) different DID Numbers must be assigned to the ISDN line and the E-CCIS line.
For the E-CCIS line, DID number is required for each D-channel.
c.) Sub Address assigned to the E-CCIS trunk must be common to both offices.
7. When using Called DID Number as addressing information:
a.) a different DID Number is required for each channel of the E-CCIS line.
b.) when multiple routes are assigned for the terminating office, call termination to an E-CCIS trunk
must not be allowed except when DID Number assigned to the trunk is dialed.
c.) different DID Numbers must be assigned to the ISDN line and the E-CCIS line.
For the E-CCIS line, DID Number is required for each D-channel.
8. Each channel used for an E-CCIS line must be controlled by a single D-channel (i.e., Each channel must
be assigned to a single ISDN line.).
9. Billing information
a.) OG billing and IC billing data should be set for each route via the ARTI command.
b.) Trunk identification number assigned by DESTINATION of the AEVT command is output to the
SMDR Record in place of a telephone number.
c.) Billing information on E-CCIS line does not include Access Code or Converted Number.
10. Peg Count service for E-CCIS line (ETS 300 172 or ISO/IEC 11572) is activated for ISDN route setting
Virtual Tie Line data. (Peg Count for ISDN line includes the route for E-CCIS line).
11. This service is established when no E-CCIS line is established or the call is originated even if all the
channels are busy.
12. The release timer is activated when the CCIS call is disconnected. 
						

							NEAX2400 IMX ISDN Features and Specifications
Page 180NDA-24281, Issue 1
E-24 Event Based CCIS - Q-SIG Transport
Service Conditions (cont’d)
13. The following features are available for the E-CCIS line:
ASYNCHRONOUS DATA SWITCHING - CCIS  [A-44] Note
ATTENDANT CAMP-ON WITH TONE INDICATION - CCIS [A-45]
ATTENDANT-CONTROLLED CONFERENCE - CCIS [A-46]
AUTOMATIC RECALL - CCIS [A-71]
AUTOMATIC NUMBER IDENTIFICATION (ANI) - CCIS [A-87]
BUSY VERIFICATION - CCIS [B-9]
BROKERAGE HOTLINE - CCIS [B-10]
CALL BACK - CCIS [C-44]
CALL FORWARDING - ALL CALLS - CCIS [C-45]
CALL FORWARDING - BUSY LINE - CCIS [C-46]
CALL FORWARDING - DON’T ANSWER - CCIS [C-47]
CALL FORWARDING - INTERCEPT - CCIS [C-48]
CALL FORWARDING - OVERRIDE - CCIS [C-49]
CALL TRANSFER - ALL CALLS - CCIS [C-50]
CALLED STATION STATUS DISPLAY - CCIS [C-51]
CALLING/CALLED NUMBER DISPLAY - CCIS [C-52]
CALL PROCESSING INDICATION - CCIS [C-53]
CALL TRANSFER - ATTENDANT - CCIS [C-54]
CONSULTATION HOLD - ALL CALLS - CCIS [C-58]
CALL FORWARDING ASSIGNMENT - ATTENDANT - CCIS [C-94]
DELUXE TRAVELING CLASS MARK - CCIS [D-70]
DATA COMMUNICATION - CCIS [D-41] Note
DATA INTERFACE - AUTOMATIC ANSWER - CCIS [D-65] Note
DATA LINE SECURITY - CCIS [D-66] Note
DATA LINE PRIVACY - CCIS [D-67] Note
DATA PRIVACY ON DEMAND - CCIS [D-68] Note
DATA TRANSPARENCY - CCIS [D-69] Note
DIAL ACCESS TO ATTENDANT - CCIS [D-71]
DIGITAL DISPLAY - STATION - CCIS [D-72]
DIGITAL DISPLAY - TRUNK - CCIS [D-73]
DIRECT-IN TERMINATION - CCIS [D-74]
DISTINCTIVE RINGING - CCIS [D-75]
DO NOT DISTURB - D
term - CCIS [D-76D]
DATA HOTLINE - CCIS [D-86]
DIALED NUMBER DISPLAY - RECALL - CCIS [D-91]
DUAL HOLD - D
term - CCIS [D-93D]
EXECUTIVE RIGHT-OF-WAY - CCIS [E-8]
ELAPSED TIME DISPLAY - CCIS [E-9]
E-911 ANI UNIFIED NUMBER OF DIGITS - CCIS [E-20]
FLEXIBLE NUMBERING OF STATIONS - CCIS [F-12]
HANDS-FREE ANSWERBACK - D
term - CCIS [H-10D] 
						

							NEAX2400 IMX ISDN Features and Specifications
NDA-24281, Issue 1
Page 181
Event Based CCIS - Q-SIG Transport E-24
Service Conditions (cont’d)
HOUSE PHONE - CCIS [H-11]
HOTLINE - CCIS [H-12]
INCOMING CALL IDENTIFICATION  - CCIS [I-16]
INDIVIDUAL ATTENDANT ACCESS - CCIS [I-17]
INTER-POSITION TRANSFER - CCIS [I-18]
INDIVIDUAL TRUNK ACCESS - CCIS [I-19]
LOOK AHEAD ROUTING - CCIS [L-25]
LDN NIGHT CONNECTION - CCIS [L-29]
MESSAGE REMINDER - CCIS [M-34]
MESSAGE REMINDER - D
term - CCIS [M-34D]
MESSAGE WAITING LAMP SETTING - ATTENDANT - CCIS [M-35]
MESSAGE WAITING LAMP SETTING - STATION - CCIS [M-36]
MISCELLANEOUS TRUNK ACCESS - CCIS [M-37]
MISCELLANEOUS TRUNK RESTRICTION - CCIS [M-38]
MODEM POOLING - CCIS [M-39] Note
MULTIPLE CALL FORWARDING - ALL CALLS - CCIS [M-40]
MULTIPLE CALL FORWARDING - BUSY LINE - CCIS [M-41]
MULTIPLE CALL FORWARDING - DON’T ANSWER - CCIS [M-42]
MULTIPLE CONSOLE OPERATION - CCIS [M-43]
MESSAGE CENTER INTERFACE - CCIS [M-67]
NIGHT CONNECTION - FIXED - CCIS [N-15]
NIGHT CONNECTION - FLEXIBLE - CCIS [N-16]
NAME DISPLAY - SYSTEM - CCIS [N-37]
OFF-HOOK QUEUING - CCIS [O-11]
OUTGOING TRUNK QUEUING - CCIS [O-12]
PAGING ACCESS - CCIS [P-28]
RESTRICTION FROM OUTGOING CALLS - CCIS [R-22]
SERIAL CALL - CCIS [S-52]
SERVICE DISPLAY - D
term - CCIS [S-53D]
SIMULTANEOUS VOICE AND DATA TRANSMISSION - CCIS [S-54]
SINGLE-DIGIT STATION CALLING - CCIS [S-55]
STATION CONTROLLED CONFERENCE - CCIS [S-56]
STATION-TO-STATION CALLING - CCIS [S-57]
STATION-TO-STATION CALLING - OPERATOR ASSISTANCE - CCIS [S-58]
STEP CALL - CCIS [S-59]
SYNCHRONOUS DATA SWITCHING - CCIS [S-60]
SUPERVISORY CALL - CCIS [S-73]
TOLL RESTRICTION - 3/6-DIGIT - CCIS [T-26]
TRUNK ANSWER FROM ANY STATION - CCIS [T-27]
UNIFORM NUMBERING PLAN - CCIS [U-5]
VOICE CALL - CCIS [V-7]
Note:This feature is available when the attribute data of ISDN calls for the E-CCIS line is assigned for data calls. 
						

							NEAX2400 IMX ISDN Features and Specifications
Page 182NDA-24281, Issue 1
I-28 ISDN Individual Calling Line Identification (ICLID)
I-28 ISDN Individual Calling Line Identification (ICLID)
General Description
The ICLID feature is used to deliver a calling-partys number through the public ISDN network to a called-party in
the same PBX.
There are two types of calling party numbers; Automatic Number Identification (ANI), used for accounting; and
Station Identification (SID).
Operating Procedure
No manual operation is required.
Service Conditions
1. For intra-office connection only, ANI is delivered to the called party.
2. For intra-office connection through public ISDN, only ANI is delivered to the called-party.
3. The DIRECT INWARD DIALING (DID) number can be converted to a telephone number in the PBX.
ISDN ICLID Connection
2400
IMX#4ESS
PRIMEGACOM 
						

							NEAX2400 IMX ISDN Features and Specifications
NDA-24281, Issue 1
Page 183
Megacom Access M-76
M-76 Megacom Access
General Description
AT&T’s MEGACOM (WATS) network can be used.
Megacom Access Connection
Operating Procedure
No manual operation is required.
Service Conditions
The available WATS service is limited to Maximal Subscribed WATS Band (MSB).
Note:The parameter band service where zone is specified on a call-by-call basis is provided by the #5ESS only.
2400
IMX#4ESS
PRIMEGACOM 
						

							NEAX2400 IMX ISDN Features and Specifications
Page 184NDA-24281, Issue 1
M-77 Megacom 800 Service
M-77 Megacom 800 Service
General Description
AT&T’s MEGACOM 800 (INWARD WATS) network can be used.
Megacom 800 Service Connection
Operating Procedure
No manual operation is required.
Service Conditions
1. When a call has terminated by the CALL-BY-CALL SERVICE SELECTION [C-105], no indication to
distinguish it from a call termination by other services is made to a terminating terminal.
2. To identify a terminal to which a call has terminated, data must be registered using the ACDD command
so that a call terminating terminal can be identified by a terminating number.
2400
IMX#4ESS
PRIMEGACOM
MEGACOM 800