NEC Neax 2400 Imx Hotel Office Data Specification

NDA-24288 CHAPTER 2
Page 9
Revision 1.0
ASSIGNMENT
5. The dialog box, shown in Figure 2-8 (information on WINSOCK setup), appears. Click OK.
Figure 2-8   Winsock 2 Setup Message Dialog Box
6. File copy starts automatically, while the displayed dialog boxes (See Figure 2-9) show the on-going
situation.
Figure 2-9   IMX MAT Installation Screen
7. If the Setup Complete dialog box appears on the screen, the file copies have finished successfully. Click
Finish to complete the IMX MAT software installation and...

CHAPTER 2 NDA-24288
Page 10
Revision 1.0
ASSIGNMENT
Note:
You should always reboot your PC after installing the IMX MAT software. Any change made during the
installation process does not take effect until the computer has been rebooted.
Figure 2-10   IMX MAT Setup Complete Dialog 

NDA-24288 CHAPTER 2
 Page 11
Revision 1.0
ASSIGNMENT
8. Review the settings you have chosen, and then click Next. The Winsock2 Setup message box displays.
Note:If you are installing IMX MAT on an NT 4.0 workstation, the Winsock2 Setup message box does not display.
NT 4.0 does not require Winsock2 in order to run.
Figure 2-11   IMX MAT Installing Winsock2 Message Box
9. After Winsock2 is installed, the Winsock2 Setup dialog box displays. This is an informational message
only. Click OK to continue...

CHAPTER 2 NDA-24288
Page 12
Revision 1.0
ASSIGNMENT
11. Click Next. The Select Components dialog box displays.
Figure 2-14   DAO Select Components Screen
12. Uncheck the ODBCDirect box and click Next. The Select Components dialog box displays.
Note:If you do not uncheck the ODBCDirect box, error messages display once the DAO Setup program
completes. IMX MAT will run properly even though these messages display.
Figure 2-15   Select Components Screen 

NDA-24288 CHAPTER 2
 Page 13
Revision 1.0
ASSIGNMENT
13. Click Next. The DAO Setup Screen displays.
Figure 2-16   DAO Setup Screen
14. After the DAO files are installed, the DAO Information message box displays. Click OK. The IMX MAT
Installation screen displays.
Figure 2-17   DAO Information Message 

CHAPTER 2 NDA-24288
Page 14
Revision 1.0
ASSIGNMENT
15. To run the IMX MAT software, click the IMX MAT icon on the desktop or select it from the Start/
Program menu. The IMX MAT menu displays as shown in Figure 2-18.
Figure 2-18   IMX MAT Main Menu
16. To configure the PBX Alias, use the instructions in Section 6.2, TCP/IP Connection.
Note:Once you have configured the IMX MAT, you can use the Run Command line to enter task commands, or
you can select the command from the Command Folders. You can also...

NDA-24288 CHAPTER 2
Page 15
Revision 1.0
ASSIGNMENT
5. IMX MAT Commands
The IMX MAT’s operation is very similar to that of the NEAX2400 MS-DOS MAT, so you will find that many
of the key stroke operations have been carried over into IMX MAT. In addition, some standard MS Windows
operations and key strokes are used. Use the following keys, or in some instances the mouse, to select or enter
data.
6. Configuring IMX MAT
This section explains the PBX Alias parameters you may configure using the PBX...

CHAPTER 2 NDA-24288
Page 16
Revision 1.0
ASSIGNMENT
6.1 Serial/Direct Connection
The following steps explain how to configure the PBX Alias for a serial/direct connection using the
recommended default data.
Note 1:The PBX Alias cannot have spaces in the name.
Note 2:You can use other data when configuring IMX MAT. However, it is recommended that you use the default
data as previously described when configuring a new PBX Alias.
Table 2-3 PBX Administration Default Values
PBX Alias NEAX-IMX
Connection Type...

NDA-24288 CHAPTER 2
Page 17
Revision 1.0
ASSIGNMENT
1. From the PBX menu, select Configuration to open the PBX Administration dialog box.
Figure 2-20   PBX Administration
2. Enter a name for the PBX Alias in the PBX Alias box.
Note:You can also define a PBX Alias by selecting the default NEXT-IMX or by modifying any other previously
defined Alias from the list in the PBX Alias box. If you select a PBX Alias from the list, its related
information displays in the additional fields on this dialog box. You...

CHAPTER 2 NDA-24288
Page 18
Revision 1.0
ASSIGNMENT
14. Click Add to write the data.
15. Click Close.
Note:The PBX Administration dialog box changes adapting to EX-FCCS Network. Enter the Fusion Group
Number (FUG) which the PBX to be logged-in belongs. “Connection Timeout”, “Response Timeout”, and
“Pacing Timer” text box is not provided. Others are the same as previous one. The PBX dialog box is as
shown below.
6.2 TCP/IP Connection
This section explains how to add or modify a PBX Alias in IMX MAT when...