NEC Neax 2400 Imx Hotel Office Data Specification

NDA-24288 COMMAND LIST
Page v
Revision 1.0
HOTEL COMMAND LIST IN ALPHANUMERIC ORDER
COMMAND 
NAMEFULL COMMAND NAME PAGE
AACLAssignment of Administration Station Class244
AANPAssignment of Administration Numbering Plan91
AASNAssignment of Alternated Administration Station Number243
AASPAssignment of Administration Special Access Code101
AASTAssignment of Administration Station Data237
ADNRAssignment of Day/Night Restriction235
ADSSAssignment of Direct Station Select253
AGCLAssignment of Guest Station...

COMMAND LIST NDA-24288
Page vi
Revision 1.0
This page is for your notes. 

NDA-24288 CHAPTER 1
Page 1
Revision 1.0
CHAPTER 1 INTRODUCTION
1. General
This manual describes how to operate the Maintenance Administration Terminal (MAT) and plan the office
data. It also contains descriptions of the parameters for the NEAX2400 IMX.
2. How to Follow This Manual
The contents of this manual are:
• CHAPTER 1 INTRODUCTION
This chapter explains how to use this manual.
CHAPTER 2 ASSIGNMENT
This chapter explains the system configuration and system specifications required to install and run...

CHAPTER 1 NDA-24288
Page 2
Revision 1.0
This page is for your notes. 

NDA-24288 CHAPTER 2
Page 3
Revision 1.0
ASSIGNMENT
CHAPTER 2 ASSIGNMENT
1. General
This chapter describes the information needed to install and operate the Maintenance Administration Terminal
(MAT) software.
The IMX MAT software has the following functions:
 Allows user-friendly Graphical User Interface (GUI) with Microsoft Windows 95/NT.
 Provides both an Ethernet interface and a RS232C interface.
 Allows access to a node within the Fusion Link network using a simple Login operation,
 Supports...

CHAPTER 2 NDA-24288
Page 4
Revision 1.0
ASSIGNMENT
2.2 IMX MAT and IMX Connection
Figure 2-1 shows a serial/direct connection to the IOC card of IMX. The serial/direct connection allows
you to access the IMX and the different nodes via the Fusion Link.
Figure 2-1   Serial/Direct Connection to IMX
IMX MAT software supports serial/direct connection to the target IMX. As seen in Figure 2-2, a modem is
required at both the remote maintenance center and the IMX site. The LINE port of the modem located at
the...

NDA-24288 CHAPTER 2
Page 5
Revision 1.0
ASSIGNMENT
2.3 Serial/Dialup Connection to IMX
Figure 2-2   Serial/Dialup Connection to IMX
The IMX MAT software provides an advanced communication software for IMX. IMX is maintained via
the LAN, WAN, or TCP/IP network on which it is running. Figure 2-3 shows the simple configuration of
the TCP/IP connection. Using this connection, any node within the Fusion Link network can be accessed
from IMX MAT.
Figure 2-3   TCP/IP Connection to Dual CPR of IMX
FUSION LINK...

CHAPTER 2 NDA-24288
Page 6
Revision 1.0
ASSIGNMENT
Figure 2-4 shows the configuration of the PBX and IMX MAT when connecting to an existing LAN. In
most cases you should use a network device such as a HUB or bridge to provide isolation from excessive
network traffic.
Figure 2-4   TCP/IP Connection (IP Address over the External LAN)
3. TCP/IP Considerations
The IMX MAT can communicate with the IMX via an Ethernet TCP/IP connection. In order for the IMX MAT
to communicate via TCP/IP, the PC must have its...

NDA-24288 CHAPTER 2
Page 7
Revision 1.0
ASSIGNMENT
If the PC does not have the network software installed and configured, a message indicating that the WINSOCK
2 setup has failed displays during the IMX MAT installation. This message is an expected response since the
IMX MAT installation program attempts to upgrade the TCP/IP WINSOCK drivers to the latest version. If these
drivers are not already installed, the upgrade process fails. The failure does not affect the successful installation
and operation...

CHAPTER 2 NDA-24288
Page 8
Revision 1.0
ASSIGNMENT
3. Enter your name and your company name on the User Information dialog box. Then, click Next.
Figure 2-6   IMX MAT User Information Dialog
4. Click Next on the Choose Destination Location dialog box to install the IMX MAT software in the default
directory.
Note:If you wish to install the software in another directory, you can click Browse to display a dialog box that
allows you to select or create another directory.
Figure 2-7   Choose Location...