NEC Neax 2400 Imx Hotel Office Data Specification

NDA-24288 CHAPTER 4
Page 99
Revision 1.0
AGNPN
AGNPN: Assignment of Guest Numbering Plan for NDM
1. General
This command assigns the minimum number of digits needed to determine the service required by the first digit
received (pre-translation). The data assigned on this command is written in the Network Data Memory (NDM)
of the Network Control Node (NCN), updating the NDM at each Local Node (LN). 
2. Precautions
1. This command is used for the Hotel Application.
2. If the Guest and Admin. Numbering are...

CHAPTER 4 NDA-24288
Page 100
Revision 1.0
AGNPN
4. Data Sheet
TENANT
NUMBER
(TN)1ST DIGIT
(1ST DC)CONNECTION
STATUS 
INDEX
 (CI)NUMBER OF 
NECESSARY DIGITS
(NND)BUSY LAMP 
FIELD
(BLF)REMARKS
1NNormal
H Hooking
BBusy
2NNormal
H Hooking
BBusy
3NNormal
H Hooking
BBusy
4NNormal
H Hooking
BBusy
5NNormal
H Hooking
BBusy
6NNormal
H Hooking
BBusy
7NNormal
H Hooking
BBusy
8NNormal
H Hooking
BBusy
9NNormal
H Hooking
BBusy
0NNormal
H Hooking
BBusy
NNormal
H Hooking
BBusy
#NNormal
H Hooking
BBusy 

NDA-24288 CHAPTER 4
Page 101
Revision 1.0
AASP
AASP: Assignment of Administration Special Access Code
1. General
This command determines the kind of service to be executed or the route to be used when a Special Access code
or trunk Access code has been dialed for the Administration Station. 
2. Precautions
1. This command is used for the Hotel Application only.
2. If the Guest and Admin. Numbering are separated (the ASYD command, SYS1, INDEX 160, bit6 = 0),
use this command for the Admin. Special Access...

CHAPTER 4 NDA-24288
Page 102
Revision 1.0
AASP
9. For the following service features, the maximum number of digits is to be assigned in the parameter NND.
10. The variable parameter appears on the MAT depending on the data in the parameter SRV.
3. Data Entry Instructions 
SERVICE FEATURE SRV SID MAX. NND
Account Code Dial SSC 41 15
Authorization Code/Forced Account Code SSC 42 15
Attendant Manual Override SSC 60 5
Access code (Max. 6 digits)
NND1 appears when SID = 15. The number of ADC
(Abbreviation...

NDA-24288 CHAPTER 4
Page 103
Revision 1.0
AASP
         STATE
(Hotel Service Code)
1 To be cleaned without ID code
2 Cleaning Completed without ID code
3 Ready for Occupancy without ID code
4 Use Not Allowed without ID code
 5-8 -
9 Maid Dial Answer Back without ID code-1
10 Maid Dial Answer Back without ID code-2
11 Maid Dial Answer Back without ID code-3
12 Maid Dial Answer Back without ID code-4
13 Maid Dial Answer Back without ID code-5
14 Maid Dial Answer Back without ID code-6
15 Maid Dial Answer...

CHAPTER 4 NDA-24288
Page 104
Revision 1.0
AASP
SERVICE INDEX
    (SID) 1-63     NO.1
56
NO.1
(Kind of Assignment Number)
  Available numbers are 0-15.
  This data is used to assign Floor Service data by the ASPF
  command.
  Note: When programming Floor Service data, ASYD SYS1 
             INDEX 165, bit7=1 must have been assigned.
SERVICE INDEX
    (SID) 1-63NO.2KIND
57
NO.2
This parameter specifies the number (0-63) of the
access code being assigned for mutual access.
This parameter serves as a...

NDA-24288 CHAPTER 4
Page 105
Revision 1.0
AASP
NND
NND appears when SIDA = 97 (Call Hold Conference).
The number of digits for an access code should be assigned in NND.
SERVICE INDEX A (SIDA) 1-255PNO 1-15A/G
56
PNO
This parameter specifies the Admin./Guest
Numbering Parameter Classification.
After assigning the PNO, go to the AOSP
command to skip this ACC.
After skipping the access code, the system
refers to the numbering data designated in
the next parameter A/G.A/G
Numbering table designation for...

CHAPTER 4 NDA-24288
Page 106
Revision 1.0
AASP
Assign the number of advanced trunk routes.ROUTE NUMBER
(RT)
COUNT
Assign a dummy route number.RT
2nd DTAuthorization code after dialing
ACC (LCR) + Destination number
0 = Out of Service
1 = In ServiceAH
ISDN-Sub Address Dialing
0 = Out of Service
1 = In ServiceSUB ROUTE NUMBER
(RT)SECOND DIAL TONE
(2nd DT) 0/1AUTHORIZATION CODE
(AH) 0/1SUB ADDRESS DIALING
(SUB) 0/1 INDEX COUNTER (COUNT)
INDEX ROUTE NUMBER (RT)
When SRV = OGC (Outgoing call) is assigned
When...

NDA-24288 CHAPTER 4
Page 107
Revision 1.0
AASP
SKIP DIGITS
(SKIP) 0-5 When SRV = UNIF (Office termination) is assigned
When SRV = ANNC (Announcement service-Single announcement) is assigned
SKIP
ANNOUNCEMENT EQUIPMENT NUMBER
(EQP) 0-127
EQP
Note:    This data is available for ACIS only. For CCIS, use the AUNE command.Assign the skip digits to terminate the call.
Assign the announcement equipment number.
EQP3 and 5-14 can be used for SRV = ANNC (Single announcement).
Assign the tenant number of
the...

CHAPTER 4 NDA-24288
Page 108
Revision 1.0
AASP
4. Data Sheet
(a) Service Code (SRV = SSC)
 
Note:When Split Call Forwarding is in service (the ASYD command. SYS1 INDEX79 bit2=1), this access code is used for
Split Call Forwarding.
TENANT 
NUMBER
 (TN)ACCESS CODE
(ACC)
MAXIMUM
6 DIGITSCONNECTION 
STATUS 
INDEX
(CI) 
N/H/BKIND OF
SERVICE 
(SRV)SERVICE
INDEX
(SID)
1 – 63NUMBER OF 
NECESSARY
DIGITS 
(NND)NUMBER OF 
NECESSARY
DIGIT FOR 
SPEED 
CALLING
(NND1)
1 – 24SERVICE CONTENTS
H Hooking SSC 1Call Hold...