NEC MT1065 Projector User Manual

E-17
S-VIDEO IN
AUDIO OUTLR
AUDIO INLR
VIDEO OUT
VIDEO IN
S-VIDEO OUT
VCR/ Laser disc player
Connecting Your VCR or Laser Disc Player
Audio equipment S-video cable (not supplied)
Video cable (not supplied)
Audio cable (not supplied)
Use common RCA cables (not provided) to connect your VCR, laser
disc player or document camera to your projector.
To make these connections, simply:
1. Turn off the power to the projector and VCR, laser disc player or
document camera.
2. Connect one end of your RCA cable to...

E-18
PROJECTING AN IMAGE (BASIC OPERATION)
This section describes how to turn on the projector and to project a
picture onto the screen.
Turning on the Projector
NOTE:
• When plugging in or unplugging the supplied power cable, make sure that the
main power switch is pushed to the off[O] position. Failure to do so may cause
damage to the projector.
• The projector has two power switches: main power switch and POWER button
(POWER ON and OFF on the remote control)
• The projector has a feature to prevent...

E-19
Selecting a Source
Selecting the computer or video source
Using the Remote Control
ASPECT OFF
VIDEO
AUTO ADJ.RGB VIEWER
LASERON
3D REFORMHELPPOINTER
VOLUME MAGNIFY
ZOOMPIC-MUTESLIDE
FOLDER
SLIDE
LIST
POWER
FREEZE
FOCUS
Press any one of the RGB, VIDEO or
VIEWER buttons.
Source List
NOTE: If no input signal is available, the projector will display a blue background(factory preset).
Selecting from Source List
Press and quickly release the SOURCE button on the projector cabinet
to display the Source...

E-20
Focus
Use the FOCUS Button (+/-) to obtain the best focus.
Correcting the Horizontal and Vertical Key-
stone Distortion (3D Reform)
Use the 3D Reform feature to correct keystone (trapezoidal) distortion
to make the top or bottom and the left or right side of the screen longer
or shorter so that the projected image is rectangular.
In the following description, 3D Reform (Cornerstone) correction can be
done with the USB mouse or remote control, cabinet buttons.
When using the USB connected to the...

E-21
5. Press the ENTER button.
6. Use the SELECT 

 button to move the projected image frame
as shown on the example.
7. Press the ENTER button.
Screen
The confirmation screen is displayed.
On the Cornerstone adjustment screen, select
“Exit” and then “OK”, or press the CANCEL but-
ton on the remote control. 8. Use the SELECT 

 button to select another icon which points
in the direction.
Screen
9. Press the SELECT 
 or  button to highlight the [OK] and press the
ENTER button.
This completes the...

E-22
Optimizing RGB Picture Automatically
Adjusting the Image Using Auto Adjust
Optimizing RGB image automatically
Press the Auto Adjust button to optimize an RGB image automatically.
[Poor picture]
[Normal picture]
AUTO ADJ.
Press the Auto Adjust button to fine-tune the computer image or to re-
move any vertical banding that might appear and to reduce video noise,
dot interference or cross talk (this is evident when part of your image
appears to be shimmering). This function adjusts the clock...

E-23
Setting the function switch
There are two switches on the bottom of the battery case: an applicable
projector selector switch (1) and laser enable/disable switch (2). Check
the projector being used and decide whether to enable or disable laser,
then set these switches as necessary using the tip of a thin ball-point
pen. On this model, an applicable projector selector switch (1) is not
used.
ON OFF
Switch (2)
On: Enabled (the laser lights when the LASER button is pressed)
[Factory default]
Off:...

E-24
ASPECT OFF
VIDEO
AUTO ADJ.RGB VIEWER
LASERON
3D REFORMHELPPOINTER
VOLUME MAGNIFY
ZOOMPIC-MUTESLIDE
FOLDER
SLIDE
LIST
POWER
FREEZE
FOCUS
ASPECT OFF
VIDEO
AUTO ADJ.RGB VIEWER
LASERON
3D REFORMHELPPOINTER
VOLUME MAGNIFY
ZOOMPIC-MUTESLIDE
FOLDER
SLIDE
LIST
POWER
FREEZE
FOCUS
CONVENIENT FEATURES
Using the Remote Mouse Function
The built-in remote mouse function enables you to operate your
computers mouse functions from the remote control (Computer mode).
It is a great convenience for clicking through...

E-25
Turning Off the Image and Sound
Press the Picture Mute button to turn off the image and sound for a
short period of time. Press again to restore the image and sound.
PIC-MUTE
Freezing a Picture
Press the Freeze button to freeze a picture. Press again to resume
motion.
FREEZE
Using the Pointer
You can use one of eight pointers to draw your audiences attention to
the portion of a projected image you want.
Press the Pointer button to dis-
play the pointer.
POINTER
Press the Pointer button to display...

E-26
Using the USB Mouse
Using the supplied USB mouse gives you a smooth operation. A com-
mercially available USB mouse can be also used.
NOTE: There may be some brands of USB mouse that the projector does not
support. The scroll button on the supplied USB mouse does not work with the
projector.
Operate the Menus using the USB mouse
Mouse Cursor
When connecting a USB mouse to the projector, you get a mouse
cursor on the screen.
Unless you use your USB mouse within 10 seconds, the mouse cur-
sor...