NEC MT1065 Projector User Manual

E-7
11 10 9 8
4
14 12 13256
17
3
Top Features
1. POWER Button (ON / STAND BY)(  )
Use this button to turn the power on and off when the main power is
supplied and the projector is in standby mode.
NOTE: To turn on or off the projector, press and hold this button for a mini-mum of two seconds.
2. POWER Indicator
When this indicator is green, the projector is on; when this indicator
is orange, it is in standby or idle mode. See the Power Indicator sec-
tion on page E-55 for more details.
3. STATUS...

E-8
1. RGB1 IN / Component Input Connector (Mini D-Sub 15 Pin)
Connect your computer or other analog RGB equipment such as IBM
compatible or Macintosh computers. Use the supplied RGB cable to
connect to your computer. This also serves as a component input
connector that allows you to connect a component video output of
component equipment such as a DVD player. This connector also
supports SCART output signal. See page E-15 for more details.
RGB1 AUDIO Input Mini Jack (Stereo Mini)
This is where you...

E-9
Part Names of the Remote Control
NOTE: If you are using a Macintosh computer, you can click either the right-clickor left-click button to activate the mouse.
NOTE: The functions flagged with an asterisk (*) are not available on MT860.
PJFREEZE3D REFORMPIC-MUTEE
OFF
VIDEO
AUTO ADJ.RGB
VIEWE
R
LASERONPOW
ER
SELECT
21
3
1. Infrared Transmitter
Direct the remote control toward
the remote sensor on the projec-
tor cabinet.
2. LASER Pointer
Beams a laser light when the LA-
SER button is pressed.
3. Remote...

E-10
MENU
PJ
ASPECT OFF
VIDEO
AUTO ADJ.
RGB VIEWER
LASERON
3D REFORM
HELPPOINTER
VOLUME MAGNIFY
ZOOMPIC-MUTE
SLIDE
FOLDER
SLIDE
LIST
ENTERCANCEL
POWER
SELECT
FREEZE
FOCUS
16
21
19
22
27
28
29 17
20
23
25
26 2415 14 1211 109 78 5 64
18
13
22. PICTURE MUTE Button
This button turns off the image and sound for a short period of time.
Press again to restore the image and sound.
NOTE: When the menu is displayed, a press of this button mutes an imageand sound without turning off the menu.
23. VOLUME (+)(–)...

E-11
Battery Installation
1. Press firmly and slide the battery cover off.
2. Remove both old batteries and install new ones (AA). Ensure that
you have the batteries polarity (+/-) aligned correctly.
3. Slip the cover back over the batteries until it snaps into place. Do not
mix different types of batteries or new and old batteries.
Note on Remote Control Operation:
If you press and hold the SELECT 
 button while installing new
batteries, the remote control may fail to work properly.
Should this...

E-12
3
1
2
INSTALLATION AND CONNECTIONS
This section describes how to set up your projector and how to connect video and audio sources.
To the wall outlet.
Setting Up the Screen and the Projector
Selecting a Location
The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is approximately 25 (0.64 m)
measured diagonally when the projector is roughly 39.4 inches (1.0 m) from the wall or screen. The largest the image can be is 500 (12.7 m) when
the...

E-13
NOTE: Distances may vary +/-5%.
Reflecting the Image
Using a mirror to reflect your projectors image enables you to enjoy a
much larger image. Contact your NEC dealer if you need a mirror. If
youre using a mirror and your image is inverted, use the MENU and
SELECT buttons on your projector cabinet or 
 buttons on your re-
mote control to correct the orientation. (See page E-44.) WARNING
* Installing your projector on the ceiling must be done by a quali-
fied technician. Contact your NEC dealer for...

E-14
Making Connections
NOTE: When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning on the power to the notebook PC. In most
cases signal cannot be output from RGB output unless the notebook PC is turned on after connecting with the projector.
* If the screen goes blank while using your remote control, it may be the result of the computers screen-saver or power management software.
* If you accidentally hit the POWER button on the remote control, wait...

E-15
To connect SCART output (RGB)
Before connections: An exclusive SCART adapter (ADP-SC1) and a
commercially available SCART cable are required for this connection.
NOTE:
• Audio signal is not available for this connection.
• The RGB IN 2 connector does not support Plug & Play.
RGB 1 IN
Video equipment
such as DVD playerProjector
ADP-SC1Commercially available
SCART cableFemale
1. Turn off the power to the projector and your video equipment.
2. Use the NEC ADP-SC1 SCART adapter and a commercially...

E-16
AUDIO OUTL
AUDIO INLRRComponentYCbCr
RGB 1 IN
RGB 2 IN
Connecting Your DVD Player
DVD player
You can connect your projector to a DVD player with component output
or Video output. To do so, simply:
1. Turn off the power to your projector and DVD player.
2. If your DVD player has the component video (Y,Cb,Cr) output, use a
commercially available component video cable (RCAX3) and the op-
tional 15-pin-to-RCA (female)

3 cable to connect your DVD player
to the RGB IN1 or IN2 connector on the projector....