NEC Mt1065 Lcd Projector Users Manual

							E-17
S-VIDEO IN
AUDIO OUTLR
AUDIO INLR
VIDEO OUT
VIDEO IN
S-VIDEO OUT
VCR/ Laser disc player
Connecting Your VCR or Laser Disc Player
Audio equipment S-video cable (not supplied)
Video cable (not supplied)
Audio cable (not supplied)
Use common RCA cables (not provided) to connect your VCR, laser
disc player or document camera to your projector.
To make these connections, simply:
1. Turn off the power to the projector and VCR, laser disc player or
document camera.
2. Connect one end of your RCA cable to the video output connector on
the back of your VCR or laser disc player, connect the other end to
the Video input on your projector. Use an audio cable (not supplied)
to connect the audio from your VCR or laser disc player to your audio
equipment (if your VCR or laser disc player has this capability). Be
careful to keep your right and left channel connections correct for
stereo sound.
3. Turn on the projector and the VCR or laser disc player.
NOTE: Refer to your VCR or laser disc player owners manual for more informa-tion about your equipments video output requirements.
NOTE: An image may not be displayed correctly when a Video or S-Video sourceis played back in fast-forward or fast-rewind via a scan converter.
Connecting the Supplied Power Cable
Connect the supplied power cable to the projector.
First connect the supplied power cables three-pin plug to
the AC IN of the projector, and then connect the other
plug of the supplied power cable in the wall outlet.
AC INRGB2 INRGB  OUT AUDIO
AUDIODVI INUSB(MOUSE/HUB)REMOTEAUDIO
AUDIOG/Y
B/CbHV
RGB1 IN
S-VIDEO INVIDEO IN
AUDIO
AUDIO
AUDIOL/MONORL/MONORAUDIO OUT L/MONORPC CONTROL
1
2 
						

							E-18
PROJECTING AN IMAGE (BASIC OPERATION)
This section describes how to turn on the projector and to project a
picture onto the screen.
Turning on the Projector
NOTE:
•When plugging in or unplugging the supplied power cable, make sure that the
main power switch is pushed to the off[O] position. Failure to do so may cause
damage to the projector.
•The projector has two power switches: main power switch and POWER button
(POWER ON and OFF on the remote control)
•The projector has a feature to prevent itself from being used by unauthorized
individuals. To use this feature, register your PC card as a protect key. See
Security in Projector Options on page E-53 for more details.
To turn on the main power to the projector, press the Main Power switch
to the ON position ( I ).
Before you turn on your projector, ensure that the computer or video
source is turned on and that your lens cap is removed.
Only after you press the ON/STAND BY button on the projector cabinet
or POWER ON button on the remote control for a minimum of 2 sec-
onds will the power indicator turn to green and the projector become
ready to use.
Note on Startup screen (Menu Language Select screen)
When you first turn on the projector, you will get the Startup screen. This
screen gives you the opportunity to select one of the seven menu lan-
guages: English, German, French, Italian, Spanish, Swedish and Japa-
nese.
To select a menu language, follow these steps:
1. Use the SELECT 
 or  button to select one of the seven languages
for the menu.
MENU
ENTERCANCEL
SELECT
MENU
ENTERCANCEL
SELECT
2. Press the ENTER button to execute the selection.
3. The Basic menu will be displayed in the language you have selected.
To close the menu, press the CANCEL button.
After this has been done, you can proceed to the advanced menu op-
eration.
If you want, you can select the menu language later. See Language
on page E-45.
NOTE: To turn the projector on by plugging in the power cable, first turn on the
Main Power switch to ON and use the menu and enable the Auto Start feature.
(See page E-47.) Immediately after turning on the projector, screen flicker may
occur. This is not a fault. Wait 3 to 5 minutes until the lamp lighting is stabilized.
When the Lamp mode is set to Eco, the Lamp indicator will light green.
If one of the following things happens, the projector will not turn on.
*If the internal temperature of the projector is too high, the projector
detects abnormal high temperature. In this condition the projector
will not turn on to protect the internal system. If this happens, wait for
the projectors internal components to cool down.
*When the lamp reaches its end of usable life, the projector will not
turn on. If this happens, replace the lamp.
*If the lamp fails to light, and if the STATUS indicator flashes on and
off in a cycle of six times, wait a full minute and then turn on the
power.
MENU
ENTERCANCEL
SELECT 
						

							E-19
Selecting a Source
Selecting the computer or video source
Using the Remote Control
ASPECT OFF
VIDEO
AUTO ADJ.RGB VIEWER
LASERON
3D REFORMHELPPOINTER
VOLUME MAGNIFY
ZOOMPIC-MUTESLIDE
FOLDER
SLIDE
LIST
POWER
FREEZE
FOCUS
Press any one of the RGB, VIDEO or
VIEWER buttons.
Source List
NOTE: If no input signal is available, the projector will display a blue background(factory preset).
Selecting from Source List
Press and quickly release the SOURCE button on the projector cabinet
to display the Source list. Each time the SOURCE button is pressed, the
input source will change as follows: RGB1, RGB2 (computer or DVD
with component output), Video (VCR, document camera, or laser disc
player), S-Video, DVI (Digital), Viewer (slides on a PC card), or LAN
(wired or wireless signal aired from a PC).
To display the selected source, press the ENTER button.
Detecting the Signal Automatically
Press and hold the SOURCE button for a minimum of 1 second, the
projector will search for the next available input source. Each time you
press and hold the SOURCE button, the input source will change as
follows:
→ RGB1 → RGB2 → Video → S-Video → DVI (Digital)→ Viewer 
If no input signal is present, the input will be skipped. When the input
source you wish to project is displayed, release the button.
Press the ENTER button.
Adjusting the Picture Size and PositionPlace your projector on a flat level surface and ensure that the projector
is square to the screen.
Lift the front edge of the projector to center the image vertically.
Move the projector left to center the image horizontally on the screen.
*If the projected image does not appear square to the screen then
use the 3D Reform feature for proper adjustment. See page E-20.
Adjust the Tilt Foot
1. Lift the front edge of the projector.
Adjustable Tilt Foot Lever
Adjustable Tilt Foot
2. Push up the Adjustable Tilt Foot Levers on the right and left sides of
the projector to extend the adjustable tilt feet (maximum height).
3. Push down the Adjustable Tilt Foot Levers.
4. Lower the front of the projector to the desired height (max. 44.5mm/
1.8”) and release the Adjustable Tilt Foot Lever to lock the Adjustable
tilt foot. There is approximately 10 degrees of up and down adjust-
ment for the front of the projector.
Adjustable Tilt Foot Lever
WARNING: To avoid premature lamp failure, do not tilt the front of the
projector up or down by more than 15° from level. 
						

							E-20
Focus
Use the FOCUS Button (+/-) to obtain the best focus.
Correcting the Horizontal and Vertical Key-
stone Distortion (3D Reform)
Use the 3D Reform feature to correct keystone (trapezoidal) distortion
to make the top or bottom and the left or right side of the screen longer
or shorter so that the projected image is rectangular.
In the following description, 3D Reform (Cornerstone) correction can be
done with the USB mouse or remote control, cabinet buttons.
Using Auto Focus
Press and hold the AUTO ADJUST button on the cabinet or AUTO ADJ
button on the remote control for a minimum of 2 seconds. The focus
pattern will be displayed for a moment and then the best focus will be
automatically obtained.
NOTE: The Auto Functions have two options: Focus and Wall Color Correction.
When the AUTO ADJUST or AUTO ADJ button is pressed and held for a mini-
mum of 2 seconds, either item can be executed. You can decide in advance
which item will be enabled at the time of execution.
From the Advanced menu, select [Projector Options] 
→ [Auto Functions]. Youcan turn on or off Focus and Wall Color Correction. See page E-49.
NOTE: Just pressing quickly the AUTO ADJUST button on the cabinet or AUTO
ADJ button on the remote control will enable the Auto Adjust feature instead of
the Auto Focus feature.
NOTE:
Geometric Correction Tool
If you use a special shaped screen such as a cylindrical or spherical screen, a
downloadable program, Geometric Correction Tool is available.
This program (Geometric Correction Tool) enables the geometrical distortion
correction of an image when projected onto a special shaped screen with an NEC
projector. Additionally, this program allows control of the projector via a com-
puter.
For additional information visit:
US : http://www.necvisualsystems.com
Europe : http://www.neceurope.com/
Global : http://www.nec-pj.com/
CAUTION:
Do not use the tilt-foot for purposes other than originally intended.
Misuses such as gripping the tilt-foot or hanging on the wall can
cause damage to the projector.
Zoom
Use the ZOOM Button (+/-) to fine adjust the image size on the screen
You can use ZOOM +/- button to enlarge or reduce an image size within
a range of +/-15%.
Screen
Projected image
(The drawing shows the upper right corner.)
3. Press the 3D REFORM button on the remote control.
The CORNERSTONE adjustment screen is displayed.
NOTE: Press the 3D REFORM button to toggle between Cornerstone and Key-stone.
When using the remote control or cabinet buttons:
1. Project an image so that the screen is smaller than the area of the
raster.
2. Pick up any one of the corners and align the corner of the screen
with the one of the image.
Screen 4. Use the SELECT 

 button to select one icon which points in
the direction you wish to move the projected image frame.
5. Press the ENTER button.
6. Use the SELECT 

 button to move the projected image frame
as shown on the example. 
						

							E-21
6. To complete the procedure, right-click anywhere on the screen.
The confirmation screen is displayed.
7. Left-click on OK.
This completes the Cornerstone adjustment.
*To return the Cornerstone adjustment to the default settings, left-
click on Reset in Step 7.
You can save your Cornerstone changes. The changes are saved when
you turn off the projector. To do so, select [Projector Options] → [Setup]
→ [Page 4]. Select the 3D Reform Save check box. This is not selected
at the time of shipment.
* There are limitations of shapes which can be corrected using the Cor-
nerstone adjustment.
When adjusting the Cornerstone beyond these limits, you will get the
message Out of adjustment range! and no correction can be done.
Should this happen, do the Cornerstone adjustment again within the
allowable range.
* Due to limitations of accuracy within internal processes, there may be
some discrepancy of positions between the mouse cursor and corrected
shape or one corner and the other 3 corners.
NOTE: To return the 3D Reform correction setting values to the factory default,press and hold the 3D REFORM button for a minimum of 2 seconds. 7. Press the ENTER button.
Screen
The confirmation screen is displayed.
On the Cornerstone adjustment screen, select
“Exit” and then “OK”, or press the CANCEL but-
ton on the remote control. 8. Use the SELECT 

 button to select another icon which points
in the direction.
Screen
9. Press the SELECT 
 or  button to highlight the [OK] and press the
ENTER button.
This completes the keystone correction.
Selecting “Cancel” will return to the adjustment screen without saving
changes (Step 3).
Selecting Reset will return to the factory default.
Selecting Undo will exit without saving changes.
Screen
Projected image 3. Press the 3D REFORM button on the remote control.
The Cornerstone adjustment screen is displayed.
The Cornerstone adjustment screen will disappear when you move
the USB mouse cursor.
4. Point to one of the remaining 3 corners and left-click on it.
Screen
5. Do the above step 4 for the other two corners so that the projected
area becomes smaller than the screen.
Screen
Left-click on each corner.
Left-click on the corner.
When using the USB connected to the projector
Preparation: Connect the USB mouse to the projector. See page E-28.
1. Project an image so that the screen is smaller than the area of the
raster.
2. Pick up any one of the corners and align the corner of the screen
with the one of the image. (The drawing shows the upper right cor-
ner.) 
						

							E-22
Optimizing RGB Picture Automatically
Adjusting the Image Using Auto Adjust
Optimizing RGB image automatically
Press the Auto Adjust button to optimize an RGB image automatically.
[Poor picture]
[Normal picture]
AUTO ADJ.
Press the Auto Adjust button to fine-tune the computer image or to re-
move any vertical banding that might appear and to reduce video noise,
dot interference or cross talk (this is evident when part of your image
appears to be shimmering). This function adjusts the clock frequencies
that eliminate the horizontal banding in the image. This function also
adjusts the clock phase to reduce video noise, dot interference or cross
talk. (This is evident when part of your image appears to be shimmer-
ing.)
This adjustment may be necessary when you connect your computer
for the first time.
NOTE:
•Some signals may not be displayed correctly or take time.
•The Auto Adjust function does not work for component and video signal.
•If the Auto Adjust operation cannot optimize the RGB signal, try to adjust Clock
and Phase manually. See page E-41.
•Pressing and holding the AUTO ADJUST button on the cabinet or AUTO ADJ
button on the remote control for a minimum of 2 seconds will enable the Auto
Focus and the Auto Wall Color Correction feature instead of the Auto Adjust
feature.
NOTE: During 3D Reform adjustment, Aspect Ratio and Screen may not be
available. Should this happen, first reset the 3D Reform data and then do each
setting. Second repeat the 3D Reform adjustment. Changing Aspect Ratio and/
or Screen setting can limit 3D Reform in its adjustable range.
The adjustable ranges for 3D Reform are as follows:
Horizontal ........... Max ±35° approx.
Vertical ............... Max +50°/-25° approx.
*The following are conditions at the above maximum angle when all of
the following are met
•Image is projected in Wide (Zoom)
•Resolution is XGA
Higher resolution than XGA limits 3D Reform in its adjustable range.
•Menu items should be set as follows:
Aspect Ratio ............................... 4:3
Screen Type ................................ 4:3
•Horizontal and Vertical are adjusted separately.
A combination of both adjustments limits 3D Reform in its adjustable
range.
•When 4:3 Fill is selected in Aspect Ratio, Cornerstone and Hori-
zontal Keystone are not available.
Turning Up or Down Volume
Sound level from the speaker and the AUDIO OUT jack (RCA) on the
projector can be adjusted.
increase volume
Volume bardecrease volume
VOLUME
Using the Laser Pointer
You can use the laser to draw your audiences attention to a red dot that
you can place on any object.
Press and hold the LASER button to activate the laser pointer.
CAUTION:
• Do not look into the laser pointer while it is on.
• Do not point the laser beam at a person.
P
O
W
ERP
O
W
E
RO
F
F
V
I
D
E
OAUTO ADJ.R
G
BV
I
E
W
E
R
L
A
S
E
R O
NP
JA
S
P
E
C
T3D 
REFORMHELPPO
INTERV
O
L
U
M
EMAGNIFYZ
O
O
MPIC-MUTESLIDEFOLDER
SLIDELIST
SELECTFREEZE
FOCUSLASER 
						

							E-23
Setting the function switch
There are two switches on the bottom of the battery case: an applicable
projector selector switch (1) and laser enable/disable switch (2). Check
the projector being used and decide whether to enable or disable laser,
then set these switches as necessary using the tip of a thin ball-point
pen. On this model, an applicable projector selector switch (1) is not
used.
ON OFF
Switch (2)
On: Enabled (the laser lights when the LASER button is pressed)
[Factory default]
Off: Disabled (the laser does not light even when the LASER but-
ton is pressed)
Disable the laser when using in an environment in which the unit is
accessible to children.
Turning off the Projector
To turn off the projector:
First press the POWER (ON/STAND BY) but-
ton on the projector cabinet or the POWER OFF
button on the remote control for a minimum of
two seconds. The power indicator will glow or-
ange. After the projector turns off, the cooling
fans keep operating for 90 seconds (Cooling-
off time).
Second, turn off the Main Power switch. The
power indicator will go out. Last unplug the
power cable.
CAUTION
Do not unplug the power cable from the
wall outlet or do not turn off the main power
under any one of the following circum-
stances. Doing so can cause damage to
the projector:
•While the Hour Glass icon appears.
•While the message Please wait a mo-
ment. appears. This message will be
displayed after the projector is turned
off.
•While the cooling fans are running. (The
cooling fans continue to work for 90 sec-
onds after the projector is turned off).
•While accessing a PC card. (The PC Card
Access indicator lights.)
ASPECT OFF
VIDEO
AUTO ADJ.RGB VIEWER
LASERON
3D REFORMHELPPOINTER
VOLUME MAGNIFY
ZOOMPIC-MUTESLIDE
FOLDER
SLIDE
LIST
POWER
FREEZE
FOCUS 
						

							E-24
ASPECT OFF
VIDEO
AUTO ADJ.RGB VIEWER
LASERON
3D REFORMHELPPOINTER
VOLUME MAGNIFY
ZOOMPIC-MUTESLIDE
FOLDER
SLIDE
LIST
POWER
FREEZE
FOCUS
ASPECT OFF
VIDEO
AUTO ADJ.RGB VIEWER
LASERON
3D REFORMHELPPOINTER
VOLUME MAGNIFY
ZOOMPIC-MUTESLIDE
FOLDER
SLIDE
LIST
POWER
FREEZE
FOCUS
CONVENIENT FEATURES
Using the Remote Mouse Function
The built-in remote mouse function enables you to operate your
computers mouse functions from the remote control (Computer mode).
It is a great convenience for clicking through your computer-generated
presentations. To return to the projector operation mode (Projector mode),
press the PJ button (lit red).
Connecting to your computer for the remote mouse
function
If you wish to use the remote mouse function, use the supplied USB
cable to connect the USB port (PC) of the projector and the USB port
(type A) of your computer.
NOTE: Depending on the type of connection or OS installed on your computer,you may have to restart your computer or change you computer settings.
NOTE: Wait at least 5 seconds after disconnecting the USB cable before recon-
necting it and vice versa. The computer may not identify the built-in mouse re-
ceiver if it is repeatedly connected and disconnected in rapid intervals.USB port (PC)
USB port
(Type A)
Switching operation mode between computer and projector
The three shaded buttons shown on the drawing work as a computer mouse in the Computer mode.
In the Computer mode the PJ button is not lit.
Not lit
Works as a mouse for your computer.
Works as a right-click button
for your computer.
Works as the SELECT button on the projector.
Lit red
Works as the CANCEL
button on the projector.
Works as a left-click
button for your com-
puter.Works as the ENTER
button on the projector.
When using the USB Port
For PC, the mouse receiver function can only be used with a Windows
98, Windows ME, Windows XP or Windows 2000 operating system.
•When the MENU button is pressed, the PJ button lights red to indicate that you are in the Projector mode, which allows the projector menu
operation using the three buttons.
•When the POINTER button is pressed, the PJ button lights red to indicate that you are in the Projector mode and that the SELECT 

button works as a moving button for the POINTER or magnified image.
•If no buttons are pressed within 60 seconds, the PJ buttons light goes out to indicate that you are in the Computer mode. To enable the projector
menu operation again, press the PJ button to light red. To move the pointer or a magnified image again, turn off the pointer and then turn on the
pointer (press the POINTER button two times).
•When the PJ button is lit, if you want to use the mouse function immediately, press the PJ button to return to the Computer mode (not lit).
During Computer mode:
In Computer mode, by pressing the ENTER button for 2 seconds or more then releasing, the drag mode is set and the drag operation can be
performed simply by pressing the SELECT 
 (mouse) button. To drop the item, press the ENTER (left click) button again or press the
CANCEL (right click) button. 
						

							E-25
Auto 3D ReformAuto 3D Reform automatically corrects distortion by sensing the outline
or outer frame of your screen with the projector’s built-in image sensor
to project an image within the screen.
NOTE:
•The Auto 3D Reform feature supports screen sizes between 30” and 200”.
•If the screen has the same brightness as its background, the built-in image
sensor on the front of the projector can fail to recognize the outline or outer
frame of the screen.
Should this happen, the Auto 3D Reform feature cannot function.
If irregular colors, flaw or change of color are seen on the screen, the built-in
sensor can mistakenly interpret the outline or outer frame of the screen.
•If there is an object between the built-in sensor and the screen, the screen
cannot be recognized.
•The Auto 3D Reform feature does not support reflective screens. Matt type or
beads type screens are recommended.
Executing the Auto 3D Reform feature
1. Project an image.
See the user’s manual or the quick connect guide for projecting an
image.
2. Press the 3D REFORM button.
The 3D Reform (Cornerstone) screen is displayed.
Projected area
3. Press and hold the AUTO ADJUST button for a minimum of 2 sec-
onds.
A guide pattern that shows available area for Auto 3D Reform is dis-
played.
*The AUTO ADJ. button on the remote control can also be used for
this purpose.
Screen’s outer frame 4. Place the projector adjusting its orientation and the angle so that the
outline (outer frame) of the screen can be positioned within the gray
area of the projected guide pattern.
5. Highlight [Start] and press the ENTER button.
The Auto 3D Reform feature has been executed. Processing takes
about 20 seconds
*To cancel, use the SELECT 
 or  button to highlight [Cancel] and
press the ENTER button.
NOTE:
*When “4:3 Fill is selected in “Aspect”, the Auto 3D Reform feature is not
available.
*If the screen’s outer frame is larger than gray area of the guide pattern as
shown, the Auto 3D Reform feature does not function.
*In the Auto 3D Reform mode, when controlling the projector using PC con-
trol, you might not be able to make correction. (The projector can be oper-
ated with Dynamic Image Utility 2.0, Image Express Utility 1.0 and HTTP
Server function.)
Not recommended 
						

							E-26
Setting Screen of Auto 3D Reform
1. Press the MENU button.
The Basic menu is displayed.
*When the Advanced menu is displayed, go to Step 3.
2. Use the SELECT 

 or  button to highlight “To Advanced Menu” and
press the ENTER button.
The Advanced menu is displayed.
3. Use the SELECT 

 or  button to highlight “Projector Options”.
Press the SELECT   button. The “3D Reform” option is highlighted.
4. Use the SELECT 

 or  button to highlight “Auto Functions”.
Press the SELECT  button. The “Auto Functions” screen is dis-
played.
Focus ............. See page E-49.
Wall Color
Correction ...... See page E-49.
3D Reform ..... Clear a check mark from the check box to disable
the Auto 3D Reform.
Adjustment
Inside ............. Corrects so that an image is projected inside of
the screen outline.
Outside .......... Corrects so that an image is projected outside of
the screen outline.
Sensitivity ...... If the built-in sensor sensitivity is so strong that it
recognizes even lines within the screen, select
“Lower”. If the built-in sensor sensitivity is too weak
to recognize the screen, select “Higher”.
NOTE: If you failed to correct for placing the image inside of the screen using
[Inside], the projector automatically corrects to project the image larger than the
outer frame of the screen.