NEC Mt1055 Lcd Projector Users Manual

E Ð 8
1. Source Button
Use this button to select a video source such as a PC, VCR, DVD
player or PC Card Viewer (PC card).
Each time this button is pressed, the input source will change as fol-
lows:
® RGB1 ® RGB2 ® Video ® S-Video ® PC Card Viewer ¾
If no input signal is present, the input will be skipped.
2. Auto Adjust Button (RGB only)
Use this button to adjust Position-H/V and Pixel Clock/Phase for an
optimal picture. Some signals may not be displayed correctly or take
time to switch between...

E Ð 9
MENURCE
AUTO
 ADJUST
U
S
B
C CONTROLMOUSE
OUTPUTREMO
CONTR
INPU
P
C
-
C
A
R
D
Terminal Panel Features
Slot for Kensington
MicroSaver Security System14
USB
12 3
4
1. USB Terminal
Connect a commercially available mouse that supports USB. You can
operate the menu or PC Card Viewer with the USB mouse via this
terminal.
Note that this terminal is not used with a computer and that there may
be some brands of USB mouse that the projector does not support.
2 PC Card Slot
Insert a PC card here.
3. PC Card...

E Ð 10
Remote Control Features
NOTE: If you are using a Macintosh computer, you can click either the right-click or left-click button to activate the mouse.
NOTE: If any one of the buttons is pressed and held for 60 seconds or more,
the button operations will cease to operate. This is not a malfunction, rather it
is a feature used to prolong battery power. To cancel this feature, press any one
of the buttons other than the Mouse button.
1. Infrared Transmitter
Direct the remote control toward the remote...

E Ð 11
16. Cancel/ Right Click Button
When you are in the Computer mode, this button works as the mouse
right button.
When you are in the Projector mode, which is indicated by lighting the
PJ button:
Press this button to exit Menus. It works the same way as the ÒCan-
celÓ button on the cabinet.
17. Pointer Button
Press this button to display one of the eight pointers; press again to
hide the pointer. You can move your pointer icon to the area you want
on the screen using the Mouse button.
18. Help...

E Ð 12
Operating Range
7m
Remote Control Battery Installation
1. Press firmly and slide the battery cover off.
2. Remove both old batteries and install new ones (AA). Ensure that
you have the batteries polarity (+/Ð) aligned correctly.
3. Slip the cover back over the batteries until it snaps into place.
Do not mix different types of batteries or new and old batteries.
Remote Control Precautions
¥ Handle the remote control carefully.
¥ If the remote control gets wet, wipe it dry immediately.
¥ Avoid...

E Ð 13
Switching operation mode between mouse and projector
The three shaded buttons shown on the drawing work as a computer mouse in the Computer mode.
In the Computer mode the PJ button is not lit.
¥ When the MENU button is pressed, the PJ button lights red to indicate that you are in the Projector mode, which allows the projector menu
operation using the three buttons.
¥ When the POINTER button is pressed, the PJ button lights red to indicate that you are in the Projector mode and that the MOUSE st
§...

E Ð 14
2. INSTALLATION
This section describes how to set up your MultiSync MT1055/MT1050/
MT850 projector and how to connect video and audio sources.
Setting up Your Projector
Your MultiSync MT1055/MT1050/MT850 Projector is simple to set up
and use. But before you get started, you must first:
1. Determine the image size.
2. Set up a screen or select a non-glossy white wall onto which you
can project your image.
Carrying the Projector: Always carry your projector by the handle.
Ensure that the power cable...

E Ð 15
MENUENTERCANCELSELECT
POWER STATUS
ON
/OFF
SOURCEAUTO  ADJUST
AC IN
MENUENTERCANCELSELECT
POWER STATUS
ON
/OFF
SOURCE
AUTO
 ADJUST
A
C
 
I
N
Adjusting the Tilt Foot
Press and hold the Tilt button on the left side of the projector.
Lift the front edge of the projector to the height you want, and release
the button to lock the Adjustable Tilt Foot.
To fine-tune the imageÕs position vertically on the screen, rotate the
foot. Each of the rear feet height can be changed up to 0.6Ó (4mm). 

E Ð 16 Ceiling Installation
Screen top
2.9Ó (79.5mm)
Lens Center
Screen center
Screen Bottom
Throwing Distance (C)Throwing Angle (a)Projector Foot
D
B
WARNING
¥ Installing your projector on the ceiling must be done by a quali-
fied technician. Contact your NEC dealer for more information.
* Do not attempt to install the projector yourself.
¥ Only use your projector on a solid, level surface. If the projector
falls to the ground, you can be injured and the projector se-
verely damaged.
¥ Do not use the...

E Ð 17
10.3
10.1
10.1
10.0
10.0
10.0
10.0
9.9
9.9
9.9
9.8
9.8
9.8
9.8 DiagonalWidth Height wide telephoto wide telephotoB
C Screen Size
Da40
1016
60
1524
67
1701.8
72
1828.8
84
2133.6
90
2286
100
2540
120
3048
150
3810
180
4572
210
5334
240
6096
270
6858
300
7620inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm32
812.8
48
1219.2
53.6
1361.44
57.6
1463.04
67.2
1706.88
72
1828.8
80
2032
96
2438.4
120
3048
144
3657.6
168
4267.2
192
4876.8
216...