NEC Ht1000 Entertainment Projector Users Manual

E-17
Connecting the Supplied Power Cable
Connect the supplied power cable to the projector.
First connect the supplied power cables three-pin plug to the AC IN of
the projector, and then connect the other plug of the supplied power
cable in the wall outlet.
PC CONTROL
RGB INDVI-D IN SG TRIGGER
VIDEO IN
S-VIDEO INS-VIDEO S-VIDEO
RGB/DVI RGB/DVI VIDEO VIDEO
AUDIO IN AUDIO INCOMPONENTY
Cb/Pb
Cr/Pr
When Viewing a DVI Digital Signal:
To project a DVI digital signal, be sure to connect the PC and the projec-...

E-18
PROJECTING AN IMAGE (BASIC OPERATION)
This section describes how to turn on the projector and to project a
picture onto the screen.
Tu r n ing on the Projector
NOTE:
•When plugging in or unplugging the supplied power cable, make sure that the
main power switch is pushed to the off[O] position. Failure to do so may cause
damage to the projector.
•The projector has two power switches: main power switch and POWER button
(POWER ON and OFF on the remote control)
•The projector has a feature to prevent...

E-19
Press and hold the SOURCE button for a minimum of 1 second, the
projector will search for the next available input source. Each time you
press and hold the SOURCE button, the input source will change as
follows:
→ Video → S-Video → Component → RGB → DVI(DIGITAL) → Viewer 
If no input signal is present, the input will be skipped. When the input
source you wish to project is displayed, release the button.
Press the ENTER button.
Selecting a Source
Selecting the computer or video source
Using the...

E-20
The rear foot height can be changed. Rotate the rear foot to the desired
height, but the vertical distance from the bottom to the desk or floor
should be 1 (25 mm) to make the projector horizontal on the flat sur-
face.
PC CONTROL
RGB INDVI-D IN SG TRIGGER
VIDEO IN
S-VIDEO INS-VIDEO S-VIDEO
RGB/DVI RGB/DVI VIDEO VIDEO
AUDIO IN AUDIO INCOMPONENTY
Cb/Pb
Cr/Pr
Up
Down
Up
Down
CAUTION:
Do not use the tilt-foot for purposes other than originally intended.
Misuses such as gripping the tilt-foot or hanging...

E-21
5. Press the ENTER button.
6. Use the SELECT 

 button to move the projected image frame
as shown on the example.
7. Press the ENTER button.
Screen
The confirmation screen is displayed.
On the Cornerstone adjustment screen, select
“Exit” and then “OK”, or press the CANCEL but-
ton on the remote control. 8. Use the SELECT 

 button to select another icon which points
in the direction.
Screen
9.Press the SELECT 
 or  button to highlight the [OK] and press the
ENTER button.
This completes the...

E-22
Turning Up or Down Volume
Sound level from the speaker on the projector can be adjusted.
increase volume
Volume bardecrease volume
VOLUME
Turning off the Projector
To turn off the projector:
First press the POWER (ON/STAND BY) but-
ton on the projector cabinet or the POWER OFF
button on the remote control for a minimum of
two seconds. The power indicator will glow or-
ange. After the projector turns off, the cooling
fans keep operating for 90 seconds (Cooling-
off time).
Second, turn off the Main...

E-23
CONVENIENT FEATURES
Using Sweet Vision function Button
Press the EFFECTOR button to display the Sweet Vision set screen.
You can set options for the Sweet Vision feature in the Setup from the
menu.
Move the viewable
area up or down
Move the position of
an image up or downZoom or V-Zoom UP DOWN
Cinema UP DOWN
EFFECTOR
POSITION
NOTE: This button works only for User in the Picture Management. Even if
User is selected in the Picture Management, this button may not work depend-
ing on the signals or...

E-24
Turning Off the Image and Sound
Press the Picture Mute button to turn off the image and sound for a
short period of time. Press again to restore the image and sound.
PIC-MUTE
Freezing a Picture
Press the Freeze button to freeze a picture. Press again to resume
motion.
FREEZE
Enlarging and Moving a Picture
You can enlarge the area you want up to 400 percent.
To  do so:
To enlarge the image:
1. Press the MAGNIFY(+) button.
Getting the On-line Help
You get the contents about Help.
Display Help
Exit...

E-25
Changing Background Logo
You can change the default background logo using the PC Card Files
feature.
NOTE: File size must be 256KB or less. Other file formats than JPEG and BMPare not available.
1.From the menu, select [Tools] 
→ [PC Card Files] to display a list of all
the files stored in the PC card so that you can select a file you want to
use as a background logo.
2.The Logo button allows you to select a background logo from graphic
files on a PC card and change to it as the background logo....

E-26
USING THE VIEWER
Making the Most out of the Viewer Func-
tion
Features
You can view graphic data, capture, and play images on the projector. A
PC card is used to view presentation data prepared on the computer
and to capture and play images projected with the projector.
The Viewer feature allows you to view slides stored on a PC memory
card (referred to as PC card in this manual) on the projector. Even if no
computer is available, presentations can be conducted simply with the
projector. This...