NEC Ht1000 Entertainment Projector Users Manual

E-7
910 45 11
678 12 1 32
Top Features
1. POWER Button (ON / STAND BY) (  )
Use this button to turn the power on and off when the main power is
supplied and the projector is in standby mode.
NOTE: To turn on or off the projector, press and hold this button for a mini-mum of two seconds.
2. STATUS Indicator
If this light blinks red rapidly, it indicates that an error has occurred,
the lamp cover is not attached properly or the projector has over-
heated. If this light remains orange, it indicates that you...

E-8
PC CONTROL
RGB INDVI-D IN SC TRIGGER
VIDEO IN S-VIDEO IN
S-VIDEO S-VIDEORGB/DVI
RGB/DVI VIDEO
VIDEO AUDIO INAUDIO INCOMPONENT
YCb/Pb Cr/Pr
93511
2 41 10 8671213
Terminal Panel Features
1. RGB IN / Component Input Connector (Mini D-Sub 15 Pin)
Connect your computer or other analog RGB equipment such as IBM
compatible or Macintosh computers. Use the supplied RGB cable to
connect to your computer. This also serves as a component input
connector that allows you to connect a component video output of...

E-9
13. ENTER Button
Executes your menu selection and activates items selected from the
menu.
14. CANCEL Button
Press this button to exit Menus. Press this button to return the ad-
justments to the last condition while you are in the adjustment or
setting menu.
15. ASPECT Button
Press this button to display the Aspect Ratio select screen. See page
E-36.
16. FREEZE Button
This button will freeze a picture. Press again to resume motion.
17. 3D REFORM Button
Press this button to enter 3D Reform to correct...

E-10
Battery Installation
1. Press firmly and slide the battery cover off.
2.Remove both old batteries and install new ones (AA). Ensure that
you have the batteries polarity (+/-) aligned correctly.
3.Slip the cover back over the batteries until it snaps into place. Do not
mix different types of batteries or new and old batteries.
Remote Control Precautions
•Handle the remote control carefully.
•If the remote control gets wet, wipe it dry immediately.
•Avoid excessive heat and humidity.
•If you will not...

E-11
INSTALLATION AND CONNECTIONS
This section describes how to set up your projector and how to connect video and audio sources.
Your projector is simple to set up and use. But before you get started, you must first:
z
Set up a screen and the projector.
xConnect your video equipment to the projector. See page E-13 – 17.
cConnect the supplied power cable. See page E-17.
NOTE: Ensure that the power cable and any other cables are disconnected before moving the projector. Whenmoving the projector or when it...

E-12
Distance Chart
Throw Distance and Screen Size
The following shows the proper relative positions of the projector and
screen. Refer to the table to determine the position of installation.
WARNING
*Installing your projector on the ceiling must be done by a quali-
fied technician. Contact your NEC dealer for more information.
*Do not attempt to install the projector yourself.
•Only use your projector on a solid, level surface. If the projector falls
to the ground, you can be injured and the projector...

E-13
Making Connections
PC CONTROL
RGB INDVI-D IN SC TRIGGER
VIDEO IN S-VIDEO IN
S-VIDEO S-VIDEORGB/DVI
RGB/DVI VIDEO
VIDEO AUDIO INAUDIO INCOMPONENT
YCb/Pb Cr/Pr
VCR, DVD Player or
LaserDisc Player
Macintosh
(Desktop type or notebook type)IBM VGA or Compatibles
(Desktop type or notebook type) DVD Player
(with component output) Video Game
To video, S-video, and au-
dio inputs on the projector.
Component video cable
(RCA

3)
(Supplied)RGB Signal cable (supplied)
To mini D-Sub 15-pin connector on
the...

E-14
PC CONTROL
RGB INDVI-D IN SC TRIGGER
VIDEO IN S-VIDEO INS-VIDEO S-VIDEORGB/DVI
RGB/DVI VIDEO
VIDEO AUDIO INAUDIO INCOMPONENTYCb/Pb Cr/Pr
VIDEO INS-VIDEO IN
AUDIO OUTRL
VIDEO OUT
S-VIDEO OUT
AUDIO INLR
VCR/ Laser disc player
Connecting Your VCR or Laser Disc Player
Audio equipment S-video cable (supplied)
Composite video
cable (supplied)
Audio cable (not supplied)
Use the supplied composite video cable to connect your VCR or laser
disc player to your projector.
To make these connections, simply:
1....

E-15
Connecting Your DVD Player
PC CONTROL
RGB INDVI-D IN SC TRIGGER
VIDEO IN S-VIDEO INS-VIDEO S-VIDEORGB/DVI
RGB/DVI VIDEO
VIDEO AUDIO INAUDIO INCOMPONENTYCb/Pb Cr/Pr
COMPONENT IN
AUDIO OUTRL
COMPONENT OUT
AUDIO INLR
DVD player
You can connect your projector to a DVD player with component output
or Video output. To do so, simply:
1. Turn off the power to your projector and DVD player.
2.If your DVD player has the component video (Y,Cb,Cr) output, use
the supplied component video cable (RCA

3) to...

E-16
Connecting Your PC or Macintosh Computer
PC CONTROL
RGB INDVI-D IN SG TRIGGER
VIDEO IN S-VIDEO INS-VIDEO S-VIDEO RGB/DVI RGB/DVI VIDEO
VIDEO AUDIO INAUDIO INCOMPONENTYCb/Pb Cr/Pr
PHONE
AUDIO IN
PHONE
RGB IN
Audio cable (not supplied)
IBM VGA or Compatibles (Notebook type)
or Macintosh (Notebook type)
IBM VGA or Compatibles (Desktop type)
or Macintosh (Desktop type)RGB signal cable (supplied)
To mini D-Sub 15-pin connector on the projector. It is recommended
that you use a commercially available...