NEC Dtl8r1 Manual

							Issue 1.0
Owner’s Manual4-3
The Base Unit has three LEDs.  The operation status of the LEDs are listed below.  
Power LED
Base is powered on:  On (Blue LED)
Base is powered off:  Off
Cordless Telephone LED
Cordless Phone Operation: On
Desk Phone Operation:  Off
Desk Phone LED
Cordless Phone Operation: Off
Desk Phone Operation:  On 
Ringer Volume   To adjust the ringer volume press the Volume softkey (in Standby mode), 
then use the Up/Down arrow keys to adjust the ringer volume.  You can 
choose from four different settings:  
OFF-Vibrate
Low
Medium
High
The LCD displays the current volume setting for two seconds. 
If Ringer is set to OFF-Vibrate, it will not vibrate when in the charging 
cradle.
Vo l u m e
During a conversation, use the Up/Down arrow keys to adjust the handset 
receiver volume.
Headset Jack  Insert the Headset plug into the headset jack   Use corresponding handset 
keys to activate headset.
Table 4-1  Handset Control Functions  (Continued)
ConditionAction
VOLUME 
						

							Issue 1.0
4-4D
term Handset, Base Unit and Charging Unit
 
Figure 4-2  Base Unit Controls and Functions
1. Power LED 4. Stand
2. Cordless Phone Select 
Button and LED5. Power Adapter Jack
3. Desk Phone Select 
Button and LED6. Modular Jacks
1
46 BACK VIEW FRONT VIEW23
5
BOTTOM VIEW 
						

							Owner’s Manual5-1 
Chapter 5Optional Equipment Installation
SECTION 1  REPLACEMENT PARTS AND OPTIONAL ACCESSORIES
Optional accessories and replacement parts can be obtained by contacting your NEC 
representative.   
Figure 5-1  Optional Accessories and Replacement Parts
Telephone Cord   
Adapter for Base Unit  AAA Ni-MH 
Rechargeable Batteries  Belt Clip  
Headset   Charging Unit 
and AC Adapter 
Optional 
Handset Kit
Base Unit Stand 
						

							Issue 1.0
5-2Optional Equipment Installation
SECTION 2  INSTALLING THE OPTIONAL HEADSET
The optional headset provides a handsfree option for the Dterm Cordless DECT.  With 
the headset installed, the user can use the belt clip the carry the handset and 
conduct a conversation using the headset.  The second handset must be keyed to 
operate with the base unit.  
To install the headset:
Open the cover over the headset jack and plug the headset into the receptacle.  
No other settings are needed.  Operation of the headset is the same as the handset.  
However, the user hears through the headset earphone and talks through the 
headset microphone.  The handset earphone and microphone (mouthpiece) are 
disconnected.
Talk or Speaker key will be used to activate the headset.
Figure 5-2  Installing the Headset 
						

							Owner’s Manual6-1 
Chapter 6Setup and Operation
SECTION 1  SETTING UP AND PROGRAMMING THE DTZ-8R-1
1.1 Programming Mode
1.1.1 Training Mode (Entry)
To enter Training mode:
Press and hold 
* and # at the same time and then press the TALK key. The 
handset emits a confirmation tone and enters Training mode.  The following 
message is displayed on the LCD and the F1 LED blinks. 
IMPORTANT
The screens in this section are system-dependent and may not match your 
handset. 
						

							Issue 1.0
6-2Setup and Operation
1.1.2 Training Mode (Next Key [Softkey1] – Select Item)
To  select an item:
Press the Next key.
1.1.3 Training Mode (Func Key [Softkey2] – Change Item)
To  change an item:
Press the Func key.
1.1.4 Training Mode (Back Key [Softkey4] – Exit from Training Mode)
When the Back key is pressed while in Training mode, a key touch tone is 
emitted and a ‘Training off’ command is sent to the PBX.  The handset exits 
Training mode.
1.1.5 Training Mode (Volume Up Key – Change Each Item Setting)
The up key can change each item setting as illustrated in the following 
displays (e.g., when the F1 setting is changed, the F1 LED blinks).
The items in the display change in the following 
sequence:
F1
F1(TALK)F2F2(TALK)F3F3(TALK)
F4F4(TALK)F5F5(TALK)F6F6(TALK)
F7
F7(TALK)F8F8(TALK)OFF HOOK 
RING
F1…
The items in the display change in the following 
sequence:
LK01
LK02LK03LK04LK05LK06
LK07LK08LK09LK10LK11LK12LK13
LK14LK15LK16LNRSPDRecallFNC
ANSLK01… 
						

							Issue 1.0
Owner’s Manual6-3
F1=LK01
[▼ ] press up key
F1=LK02
[▼ ] press up key
F1=LK03
[▼ ] press up key
F1=LK04
[▼ ] press up key
F1=LK05
[▼ ] press up key
F1=LK06
[▼ ] press up key
F1=LK07
[▼ ] press up key
F1=LK08
[▼ ] press up key
F1=LK09
[▼ ] press up keyContinued on next page  
						

							Issue 1.0
6-4Setup and Operation
F1=LK10
[▼ ] press up key
F1=LK11
[▼ ] press up key
F1=LK12
[▼ ] press up key
F1=LK13
[▼ ] press up key
F1=LK14
[▼ ] press up key
F1=LK15
[▼ ] press up key
F1=LK16
[▼ ] press up key
F 1=LNR/SPD
[▼ ] press up key
F 1=Recal l
[▼ ] press up key
Continued on next page  
						

							Issue 1.0
Owner’s Manual6-5
SECTION 2  HANDSET OPERATION
This operation is one of the examples for the DTZ-8R-1 with an NEC PBX.  As a 
result, it  might be different from actual operation on your system.  Operation of 
DTZ-8R-1 in digital mode depends on each PBX specification.
2.1 Switching Between the Wired Phone and Cordless Phone 
(DTZ-8R-1 Handset)
Press the Base Left key to change to the cordless phone (DTZ-8R-1 Handset).  
When the cordless phone is selected, there is no message on the LCD.  Press the 
Base Right key to change to the wired phone.  When the wired phone is selected, 
the LCD shows ’DESK TEL’.
F1=FNC
[▼ ] press up key
F1=ANS
[▼ ] press up key
F1=LK01
IMPORTANT
❍The screens in this section are system-dependent and may not match your 
handset.
❍Depending on the system the handset may not follow automatic idle return.
Base Left Key Base Right Key 
						

							Issue 1.0
6-6Setup and Operation
2.2 Making a Call to Another Extension
To make a call to another extension:
1. Press the TA L K key on the handset.  The handset tries to connect to the 
base station while the “ACQUIRING LINK” message blinks on the LCD.
2. When connected, the handset goes into Talk mode and theTalk icon is 
turned on and displays the current volume.
Talk Key Speaker Key