NEC Call Forward Control Installation And Operations Manual

NDA-30030-003   Revision 3Page 11
Call Forward Control - Installation & Operations Manual INSTALLATION INTRODUCTION
SOFTWARE INSTALLATION (Cont)
If the current database format is not compatible with the new installation, it is converted to 
the new database format and the following status screen is displayed. Press the 
 key at the prompt to continue to the next step.
If the database conversion fails, the following status screen is displayed. Press the 
 key at the prompt to continue to the next step.
If...

Page 12NDA-30030-003   Revision 3
INSTALLATION INTRODUCTION Call Forward Control - Installation & Operations Manual
SOFTWARE INSTALLATION (Cont)
The following screen is displayed while installing the cfcadm user. Just press 
ENTER at the user id prompt to accept the default value. Note that a warning 
message is given when installing the cfcadm user, since it has the same user id as 
the cfc user. Enter y  at the warning prompt and continue.
STEP 7:   CFC Auto-Config
The installation script can load...

NDA-30030-003   Revision 3Page 13
Call Forward Control - Installation & Operations Manual INSTALLATION INTRODUCTION
SOFTWARE INSTALLATION (Cont)
During the HFC configuration load the following screen is displayed:
At the prompt, type  to continue.
During the MCI_Server configuration load the following screen is displayed:
At the prompt, type  to continue.
STEP 8:   CFC Installation Processing (No input required.)
The installation script performs several tasks following the auto configuration and...

Page 14NDA-30030-003   Revision 3
INSTALLATION INTRODUCTION Call Forward Control - Installation & Operations Manual
SOFTWARE INSTALLATION (Cont)
STEP 9:   CFC Installation Complete
When the installation script has completed the following screen is displayed.
Press  to return the APM Administration Main Menu, then either exit 
the APM Administration program or use an Alt F(#) key combination to switch to 
another screen to perform Step 10.
STEP 10: SCO UNIX Subsystem Database
In this step, the SCO UNIX...

NDA-30030-003   Revision 3Page 15
Call Forward Control - Installation & Operations Manual INSTALLATION INTRODUCTION
SOFTWARE INSTALLATION (Cont)
If the MCI_Server component is used, two tty devices must be created in the SCO 
Subsystem database. This can be done by entering the SCO UNIX administration shell 
(sysadmsh), selecting Account –
>Terminal –>Create and then creating each tty device 
(ttyn1a, ttyn1b, etc.).   Refer to the SCO UNIX Administration Manual.
STEP 11:   Reboot
When finished, the...

Page 16NDA-30030-003   Revision 3
INSTALLATION INTRODUCTION Call Forward Control - Installation & Operations Manual
APPLICATION CONFIGURATION
If the “auto-config” utility was used during installation then default APM 
configuration data was loaded for the CRC, HFC, and MCI_Server applications. 
These default settings may require modification using the Select function of the 
Application Configuration option on the APM System Administration menu. If the 
“auto-config” utility was skipped, then the CRC,...

NDA-30030-003   Revision 3Page 17
Call Forward Control - Installation & Operations Manual INSTALLATION INTRODUCTION
APPLICATION CONFIGURATION (CONT)
STEP 2:   PRIMARY CONFIGURATION PARAMETERS
On the APM Configuration Entry screen, make the entries shown below for CRC:
Make the entries shown below for HFC: Parameter Entry Parameter Definition
Application Name CRCSpecifies the name to be displayed in the APM menus.  
This name is displayed however it is entered here; lower 
case letters and punctuation are...

Page 18NDA-30030-003   Revision 3
INSTALLATION INTRODUCTION Call Forward Control - Installation & Operations Manual
APPLICATION CONFIGURATION (CONT)
STEP 3:   FACILITIES
According to instructions in the APM Operations Manual, designate the 
following NEAX2400 facilities for CRC using the Facilities command on the APM 
Configuration Entry screen:
SCF– Switch Control Facility
SMFN– Status Notification Facility
SMFR– Status Request Facility
Designate the following NEAX2400 facilities for HFC using the...

NDA-30030-003   Revision 3Page 19
Call Forward Control - Installation & Operations Manual INSTALLATION INTRODUCTION
APPLICATION CONFIGURATION (CONT)
STEP 5:   USER-DEFINED PARAMETERS
Make the entries below through the UserDefined command on the OAI 
Configuration screen for CRC:.
Make the following OAI Configuration entries for HFC:. U-D # Entry Parameter Definition
 #1*/oai/app/cfc/
data/Names-
FileIdentifies the full path and filename of the file that contains 
the names of the databases used by CRC...

Page 20NDA-30030-003   Revision 3
INSTALLATION INTRODUCTION Call Forward Control - Installation & Operations Manual
APPLICATION CONFIGURATION (CONT)
MCI_SERVER
If there is an existing on-site voice mail system with which CRC is to communicate, the 
MCI
_Server application must be configured through the Application Configuration option 
on the APM Administration Menu. The name MCI
_Server
 must be entered as User-
Defined Parameter #2 in the CRC configuration (see Step 5 above). The information that...