Namco Victory Lap Ace Driver Operators Manual

Page 11
5. INSTALLATION
5-1 Connecting the Seat Assemblies to the Main Cabinet
a. Place the main cabinet in its final position.
b. Connect the connectors between the Seat Assembly and Main Cabinet.
c. Fix the Seat Assemblies to the Cabinet using the Joint Plates, M10 hex head
screws, flat washers and spring washers taking care not to trap any wires
between the Seat Assembly and Cabinet.
5-2 Adjusting the Level Adjusters
When the seats have been assembled to the main cabinet, lower the level adjusters,
(4...

Page 12
6. LINKING TWO OR MORE MACHINES
Up to four machines (8 seats) can be linked together. 
The machines should be linked as described below.
NOTE:Each machine can draw up to 3 amps. Make sure that the power supply
is adequate.
a. Ensure that the 
power is OFF.
b. Loosen the two screws (M4x10) on the back of the main cabinet, and rem\
ove the connector cover.
c. Set the link switches to ON , EXT, and ON. (See Diag.)
d. Use the supplied link cable and connect the machines between IN and OUT 
sockets...

Page 13
e. Turn the power to each machine ON, and set the PCB ID using the test mo\
de.
(Refer to section 7-3-2 Setting the Game Options (page1 7))
Note: Settings other than those described will cause the machine to operate
incorrectly .
6-1 Setting the Link Switches
The link switches are used to set the connection between seats and machi\
nes. 
a. Setting only one machine (2 seats) Set the link switches to ON, INT, and ON.
Note: Do not use a link cable.
b. Setting two or more machines.
Set the link...

Page 14
7 ADJUSTMENTS
7-1 Turning on the PowerAfter the machine has been installed, turn ON the power. The Power switch is 
located on the rear of the Main cabinet.  (See section 4 Major Components
(page  10).)
7-2 Adjustment Switches The adjustment switches are located inside the coin door. 
1. Service Switch Press this switch to obtain game credits without incrementing the play m\
eters.
2. Test Switch Slide this switch ON to enter test mode. 
Test mode allows game testing and the changing of game...

Page 15
7-3 Test Mode
1. Open the coin door and slide the test switch ON. The Menu Screen wil\
l be displayed on the monitor.
2. Select the test required by moving the shift lever up or down. The colou\
r of the selected test will change.
3. Enter the selected test by stepping on the accelerator. Select EXIT to return to the Menu Screen (step on the accelerator when using the monitor te\
st 
screen).
4. After testing is completed, ensure that the test switch is returned to t\
he OFF position to return to...

Page 16 7-3-1 Coin Options
a. Select item (1)
COIN OPTIONS
on the menu screen,
to set the game cost
and related settings.
b. Use the shift lever to
select the required
item then step on
the accelerator.
c. Use the shift lever to
change the settings
then step on the
accelerator to store
the new values.
d. Select EXIT to
return to the menu
screen.
ITEMCONTENTSFACTORY SET
(a) Game CostCoins required for 1 credit - - - - - - settable 1 - 91
(b) Coin 1 Mech ValueNumber of pulses on meter per coin - - - - - -...

Page 17 7-3-2 Game  Options
a. Select item (2) GAME
OPTIONS on the
menu screen to set the
game options.
b. Use the shift lever to
select the required item
then step on the
accelerator.
c. Use the shift lever to
change the settings
then step on the
accelerator to store the
new values.
d. Select EXIT to return
to the menu screen.
NOTES
•The rank (level of difficulty) and number of laps must be set the same
on all positions that are linked.
•The PCB number of the seat furthest left (when facing the front of...

Page 18
ITEMDESCRIPTIONFACTORY SET
(a) PCB NumberThe PCB number should be set so that none of the linked positions have the same number
(b) Team Colour
RED 25 or 26
BLUE 3 or 4
YELLOW 17 or 18
GREEN 11 or 12
* When more than three sets (6 seats) are linked, different race numbers should be used for
the same team colours.
(c) CourseSEROW VALLEY(d) Race classBEG(e) Game difficulty (Solo time)A (long) to D (short)B
(f) Number of laps (Solo game)2 to 63
(g) Game difficulty (Linked game)A (long) to D...

Page 19
7-3-3 I/O Test
1. Select item (3) I/O TEST on the menu screen. 
2. Use the shift lever to select the required item then step on the acceler\
ator.
I/O TEST
DIP 2 12345678 ........... (a) Option Switch (CPU-PCB Sw2) 3 12345678 ........... (b) Option Switch (CPU-PCB Sw3)
LINK ON 2 COUNT 0 ........... (c) Link Check
SWITCH ........... (d) Switch Test
MOTOR ........... (e) Motor Test 
LAMP ........... (f) Lamp Test
LED ........... (g) LED Test
EXIT 
GAS: ENTER SHIFT: CHOOSE
(a) Displays the state of...

Page 20 7-3-4 Switch Test
The following screen is displayed when SWITCH is selected on the I/O screen.
I/O TEST
DIP 2 12345678
3 12345678
LINK ON 2 COUNT 0
SWITCH
(a) Accelerator ................ GAS: *0000 COIN 1: OFF .............. (e) Coin 1 switch
(b) Brake ................ BRAKE *0000 COIN 2: OFF .............. (f)  Coin 2 switch
(c) Steering ................ STEER *0000 SERVICE: OFF .............. (g) Service switch
(d) Shift ................ SHIFT CENTRE VIEW: OFF .............. (h) View change...