Namco Ridge Racer Operators Manual
Have a look at the manual Namco Ridge Racer Operators Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 93 Namco manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 14
Page
6-3-
4Sound Test (Adjusting the Sound Volume)
Select “SOUND TEST” on the menu screen to adjust the sound volume.\
The
following screen appears.
Use the steering wheel to select the item to be changed. Step on the ac\
celerator
and the item selected will stop flashing. Use the steering to adjust th\
e level. Step
on the accelerator when the desired setting is reached and the item will\
start
flashing. The steering can now select another item.
The sound volume can be adjusted in 64 steps...](http://img.usermanuals.tech/thumb/5509/63356/w64_ridge-racer-operator-s-english_d-13.png "Page 14
Page
6-3-
4Sound Test (Adjusting the Sound Volume)
Select “SOUND TEST” on the menu screen to adjust the sound volume.\
The
following screen appears.
Use the steering wheel to select the item to be changed. Step on the ac\
celerator
and the item selected will stop flashing. Use the steering to adjust th\
e level. Step
on the accelerator when the desired setting is reached and the item will\
start
flashing. The steering can now select another item.
The sound volume can be adjusted in 64 steps...")
![Page 15
Page
6-
4 Adjusting the Game After Replacing Parts (Initializing the Game)
Be sure to adjust the game with the following the instructions below aft\
er replacing any
part. Otherwise, the game will not function correctly.
1. Ensure that the accelerator and brake pedals are released and the steeri\
ng is in the centre.
2. Hold down the service switch and slide to the test switch to “ON”.\
The following screen appears on the monitor display.
3. To zero the settings press the service switch.
4. When...](http://img.usermanuals.tech/thumb/5509/63356/w64_ridge-racer-operator-s-english_d-14.png "Page 15
Page
6-
4 Adjusting the Game After Replacing Parts (Initializing the Game)
Be sure to adjust the game with the following the instructions below aft\
er replacing any
part. Otherwise, the game will not function correctly.
1. Ensure that the accelerator and brake pedals are released and the steeri\
ng is in the centre.
2. Hold down the service switch and slide to the test switch to “ON”.\
The following screen appears on the monitor display.
3. To zero the settings press the service switch.
4. When...")
![Page 16
Page
7
. HOW TO PLAY
• This is the car race game.
• Players can enjoy virtual driving with a clutch and shift lever (Automa\
tic setting is also selectable).
• Four difficulties are provided: NOVICE, INTERMEDIATE, ADVANCED and TT (Time Trial) and two types of operations can be selected use of clu\
tch and shift
lever or automatic.
(Outline of a Game) • When a player drives a car the specified number laps within the given ti\
me, he or she finishes the race, the ranking, lap time and total time are...](http://img.usermanuals.tech/thumb/5509/63356/w64_ridge-racer-operator-s-english_d-15.png "Page 16
Page
7
. HOW TO PLAY
• This is the car race game.
• Players can enjoy virtual driving with a clutch and shift lever (Automa\
tic setting is also selectable).
• Four difficulties are provided: NOVICE, INTERMEDIATE, ADVANCED and TT (Time Trial) and two types of operations can be selected use of clu\
tch and shift
lever or automatic.
(Outline of a Game) • When a player drives a car the specified number laps within the given ti\
me, he or she finishes the race, the ranking, lap time and total time are...")
![Page 18
Page
8-
2 Removing the Shield Case
1 . Perform Steps (1) and (2) described in Section 8-1.
2. Disconnect the connector of the AC Fan.
3. Remove two cup screw (M5 X 14) then take out the shield case.
8- 3 Removing the Power Control Panel
1 Perform steps 1, 2, 5 and 6 described in Section 8-1.
2. Disconnect two connectors of the EMI board, remove a cup screw (M4 X 1\
0) from the shield case door, then remove the ground terminal. (Note: d\
o not lose
the internal washer).
3. Disconnect the...](http://img.usermanuals.tech/thumb/5509/63356/w64_ridge-racer-operator-s-english_d-17.png "Page 18
Page
8-
2 Removing the Shield Case
1 . Perform Steps (1) and (2) described in Section 8-1.
2. Disconnect the connector of the AC Fan.
3. Remove two cup screw (M5 X 14) then take out the shield case.
8- 3 Removing the Power Control Panel
1 Perform steps 1, 2, 5 and 6 described in Section 8-1.
2. Disconnect two connectors of the EMI board, remove a cup screw (M4 X 1\
0) from the shield case door, then remove the ground terminal. (Note: d\
o not lose
the internal washer).
3. Disconnect the...")
![Page 19
Page
8-5 Dashboard Assy (Replacing the Fluorescent Lamp)
1. Remove five torque bolts (M5 x 12) located on the right side of the da\
shboard, then the dashboard cover (R).
2. Remove one cup screw (M5 X 12) and disconnect one connector. Then pul\
l out the FL bracket. To perform this operation, keep the right side of the \
main body
320cm distance from another machine.
3. Replace the fluorescent lamp (15W) with a new one.
8- 6 AB Pedal Assy (Replacing the Control)
1. Remove four hex head bolts (M6x20)...](http://img.usermanuals.tech/thumb/5509/63356/w64_ridge-racer-operator-s-english_d-18.png "Page 19
Page
8-5 Dashboard Assy (Replacing the Fluorescent Lamp)
1. Remove five torque bolts (M5 x 12) located on the right side of the da\
shboard, then the dashboard cover (R).
2. Remove one cup screw (M5 X 12) and disconnect one connector. Then pul\
l out the FL bracket. To perform this operation, keep the right side of the \
main body
320cm distance from another machine.
3. Replace the fluorescent lamp (15W) with a new one.
8- 6 AB Pedal Assy (Replacing the Control)
1. Remove four hex head bolts (M6x20)...")
![Page 20
Page
8-
7 Clutch Pedal Assy (Replacing the Micro Switch)
1. Remove four hex head bolts (M6x20) and withdraw the assy forwards.
2. Replace the micro switch.
8- 8 Steering Assy
8-8- 1 Replacing the control
1. Remove four button head screws (M5x12), two on the steering column and\
two on the underside front. Loosen three button head screws (M5x12), from \
the
underside rear, and remove the under cover vac-form.
2. Disconnect the four way connector.
3. Remove four hex head bolts (M10x20), two either side...](http://img.usermanuals.tech/thumb/5509/63356/w64_ridge-racer-operator-s-english_d-19.png "Page 20
Page
8-
7 Clutch Pedal Assy (Replacing the Micro Switch)
1. Remove four hex head bolts (M6x20) and withdraw the assy forwards.
2. Replace the micro switch.
8- 8 Steering Assy
8-8- 1 Replacing the control
1. Remove four button head screws (M5x12), two on the steering column and\
two on the underside front. Loosen three button head screws (M5x12), from \
the
underside rear, and remove the under cover vac-form.
2. Disconnect the four way connector.
3. Remove four hex head bolts (M10x20), two either side...")
![Page 21
Page
8-
9 Gear Shift Assy (removing)
1. Remove six button head screws (M6x16) and remove the boot cover plate.\
2. Remove twelve button head screws (M6x16) and remove the shifter cover \
plate.
3. Disconnect the six way connector.
4. Remove four hex head bolts (M6x20) retaining the shifter base plate to\
the housing assy and remove the assy.
8-1 0 Replacing the Speaker
1. Remove eight torque bolts (M5 X 12) located on the side of the main bo\
dy, then the monitor panel (R) or monitor panel (L).
2....](http://img.usermanuals.tech/thumb/5509/63356/w64_ridge-racer-operator-s-english_d-20.png "Page 21
Page
8-
9 Gear Shift Assy (removing)
1. Remove six button head screws (M6x16) and remove the boot cover plate.\
2. Remove twelve button head screws (M6x16) and remove the shifter cover \
plate.
3. Disconnect the six way connector.
4. Remove four hex head bolts (M6x20) retaining the shifter base plate to\
the housing assy and remove the assy.
8-1 0 Replacing the Speaker
1. Remove eight torque bolts (M5 X 12) located on the side of the main bo\
dy, then the monitor panel (R) or monitor panel (L).
2....")
![Page 22
Page
8-1
1Replacing the Monitor
The monitor weighs approximately 60 kgs and it is recommended THAT AT
LEAST TWO PEOPLE remove the monitor.
1. Remove 14 torque bolts (M6 X 16), then the rear cover.
2. Disconnect two connectors.
3. Remove two hexagonal bolts (M6 X 20), then take out the monitor from \
the main assy as indicated by the arrow mark.
4. Replace the monitor with a new one.
5. To replace the rear cover, hook the stud bolt of the rear cover to the h\
ole of the main body assy, then fix the...](http://img.usermanuals.tech/thumb/5509/63356/w64_ridge-racer-operator-s-english_d-21.png "Page 22
Page
8-1
1Replacing the Monitor
The monitor weighs approximately 60 kgs and it is recommended THAT AT
LEAST TWO PEOPLE remove the monitor.
1. Remove 14 torque bolts (M6 X 16), then the rear cover.
2. Disconnect two connectors.
3. Remove two hexagonal bolts (M6 X 20), then take out the monitor from \
the main assy as indicated by the arrow mark.
4. Replace the monitor with a new one.
5. To replace the rear cover, hook the stud bolt of the rear cover to the h\
ole of the main body assy, then fix the...")
Page 8- 9 Gear Shift Assy (removing) 1. Remove six button head screws (M6x16) and remove the boot cover plate.\ 2. Remove twelve button head screws (M6x16) and remove the shifter cover \ plate. 3. Disconnect the six way connector. 4. Remove four hex head bolts (M6x20) retaining the shifter base plate to\ the housing assy and remove the assy. 8-1 0 Replacing the Speaker 1. Remove eight torque bolts (M5 X 12) located on the side of the main bo\ dy, then the monitor panel (R) or monitor panel (L). 2. Ensure the correct colour wire is re-connected to each speaker terminal \ when replacing speaker. 21
Page 8-1 1Replacing the Monitor The monitor weighs approximately 60 kgs and it is recommended THAT AT LEAST TWO PEOPLE remove the monitor. 1. Remove 14 torque bolts (M6 X 16), then the rear cover. 2. Disconnect two connectors. 3. Remove two hexagonal bolts (M6 X 20), then take out the monitor from \ the main assy as indicated by the arrow mark. 4. Replace the monitor with a new one. 5. To replace the rear cover, hook the stud bolt of the rear cover to the h\ ole of the main body assy, then fix the rear cover to the main body assy with four\ teen torque bolts (M6 X 16). 22
Page 9. PA AR TS LIST CABINET DESCRIPTIONPART No Monitor 33 Hantarex Polo84000015 Speaker 4 1/2 20w (with shield can)62000006 Speaker - Piezo Horn62000046 Accelerator/Brake Pedal Assy88800021 Accelerator/Brake Control Pot (5k)76000652 Clutch Pedal Assy88800032 Steering Assy (340 degrees)88800045 Steering Control Pot (5k)76000652 Power Supply Assy - 5v/30amp83000004 Schaffner Mains Filter Input Assy66000016 Fan67000015 Fluorescent Tube 1864500000 Choke 15w63300000 100 Ohm 10w W/W Volume Control76000164 M16 Adjustable Foot88300079 75mm Castor59000005 SEAT & BASE ASSY DESCRIPTIONPART No Seat - (black)88300673 Seat Slider Mechanism88300680 Speaker 4 1/2 20w62000006 Speaker Cover Plate (Left)88300603 Speaker Cover Plate (Right)88300604 6 Speed Gear Shift Assy88300672 Gear Shift Leather Boot88300683 Bull Bar (Polished S/Steel)88300678 M16 Adjustable Foot88300079 75mm Castor59000005 23
Page DECALS DESCRIPTIONPART No Side Speaker Cover-Ridge Racer (Left)40000187 Side Speaker Cover-Ridge Racer (Right)40000193 Gear Shift Upper (A)40000188 Gear Shift Lower (B)40000189 Seat Back-Ridge Racer/Twin Turbo40000190 Namco40000191 Twin Turbo40000192 VAC-FORM PLASTICS DESCRIPTIONPART No Side Speaker Cover (Left)88300716 Side Speaker Cover (Right)88300717 Screen Surround88300720 Dashboard88300722 Dashboard Under Cover88300723 Dashboard Side Closing Cover (Left)88300724 Dashboard Side Closing Cover (Right)88300725 Steering Closing Cover88300726 Header End Closing Cover (Left)88300729 Header End Closing Cover (Right)88300730 ACRYLICS DESCRIPTIONPART No Screen Top Hood (Smoked)88300705 Speedo Front Cover88300727 Battery/Oil Front Cover88300728 Speedo Printed Polycarbonate33000115 Battery/Oil Printed Polycarbonate33000116 Ridge Racer Top Flash30000058 24