Namco Race On Operators Manual

							Page 61 8-2 Replacing the Fluorescent Lamp or Starter.
1. Remove 3off security screw (M5x12) and remove the top retaining
bracket.
2. Remove the Header Acrylic.
3. Replace the Fluorescent tube or  starter.
4. Reassemble in reverse order. 
						

							Page 62 8-3 Replacing the Camera
1. Remove 4off security screw (M5x20) and remove the Camera Joint Assy.
2. Disconnect the connector.
3. Remove 1off pozi head screw retaining the cable clamp.
4. Remove the Camera PCB Assy from the Camera Joint Assy by gently
pulling the retaining tab to the right to release the PCB .
5. Replace the Camera PCB Assy.
6. Reassemble in reverse order. 
						

							Page 63
8-4 Replacing the Camera Housing
1. Remove the Camera Joint Ass y.  (see section 8-3 page  62)
2. Remove 3off pozi head screws (M4x6) and 1off pozi head screw (M4x8), with flat and spring washer, and remove the Camera Housing.
3. Reassemble in reverse order. 
						

							Page 64 8-5 Replacing the Credit Available / View Change Switch
1. Remove 4off security screw (M5x12) and 2off security screw (5x20).
2. Disconnect the connectors and remove the Steering Vac-form.
3. Remove the switch/lamp assembly by pulling it out from the switch body.
4. Replace the switch or lamp.
5. Reassemble in reverse order. 
						

							Page 65 8-6 Removing the Steering Wheel
1. Remove 3off countersunk socket head screws and remove the centre cap.
2. Remove 3off countersunk socket head screws and remove the steering
wheel.
Note: When replacing the steering wheel ensure that the steering wheel
shaft is in the centre position and the wheel is fitted with central spoke
pointing downwards. 
						

							Page 66
8-7 Replacing the Steeering Assembly
1. Remove the steering vac-form.  (see 8-5 page 64)
2. Remove 4off pozihead screws (M5x20) and remove the Steering Support Bracket B.
3. Disconnect the Steering Motor and Steering Potentiometer connectors. 
4. Remove 4off hex head screws (M6x20) and remove the Steering assembly. 
						

							Page 67
8-8 Replacing the Steering Potentiometer
1. Remove the steering assembl y.  (see 8-6 page  65)
2. Remove 2off hex socket head screws (M4x10) holding the potentiometer mounting bracket to the front plate.
3. Slacken the grub screw (M4x10) and remove the potentiometer complete with the mounting bracket.
4. Replace the potentiometer taking care to replace the correct colour wire\
 to the correct terminal.
5.  Reassemble in reverse order.
Note: When refitting the potentiometer ensure that the grub screw engages
on the flat of the potentiometer shaft.
6 . After replacing the potentiometer ensure that the game is re- 
initialized .  (see section 7 page  57) 
						

							Page 68
8-9 Replacing the Drive Belt
1. Remove the steering assembl y.  (see 8-6 page  65)
2. Slacken the adjustment screw (hex head M6x60). 
3. Slacken the 4off hex nuts to remove the tension from the belt. 
4. Replace the drive belt. 
5. Tighten the adjustment screw (M6x60) to tension the belt correctly.
Note: Do not over tension the drive belt.
6. Retighten the 4off hex nuts.
7. Refit the steering assembly.
Note :After replacing the drive belt ensure that the game is re-initialized.
(see section 7 page  57) 
						

							Page 69
8-10 Removing the Pedal Assy
1. Remove 4off security screw (M5x20).
2. Withdraw the pedal assembly only sufficiently to disconnect the
connectors.
3 Remove the pedal assembly.
4. Reassemble in reverse order 
						

							Page 70
8-11 Replacing the Pedal Potentiometer
1. Remove the pedal asembl y.  (see 8-9 page  68)
2. Slacken the double point screw (M4x8) and remove the potentiometer complete with potentiometer bracket.
3. Replace the potentiometer ensuring that the correct colour wires go to t\
he correct terminals.
Note: When replacing the potentiometerensure that the double point screwengages on the flat of the potentiometershaft.
4. Reassemble in reverse order. 
Note :After replacing the potentiometer ensure that the game is re-
initialized .  (see section 7 page  57)