Namco Race On Operators Manual

							Page 51 6-3-3-4 Camera Check
1. Select ‘CAMERA CHECK’ from the I/O Test Screen. The following
screen is displayed:-
•In the CAMERA CHECK Screen, the current view of the camera is
displayed in the centre box.
(a) MIRROR/PHOTO
By pressing the Brake Pedal or Service Switch, the image from the
camera is frozen on the screen and the word MIRROR, just below the
image box, changes to PHOTO. This is the mage that would be used
during the game.
Pressing the Brake Pedal or Service Switch again reverts back to
current camera image, and the word PHOTO changes to MIRROR.
The mode of [MIRROR] is used for adjustment of the image, and the
mode of [PHOTO] to verify the picture to be used during the game.
(b) IRIS ADJUST
This setting is used to adjust the brightness of the image.
The brightness of the image is automatically adjusted to the optimum
value by the system, but this item allows the brightness level to be
set manually.
Select this item and press the ENTER button. Use the Select UP/
DOWN switch to make the image brighter or darker. There are three
brighter and three darker settings available.
Press the ENTER button to store the new setting and to exit this
mode.I/O TEST
CAMERA CHECK [DEFAULT IN GREEN]
MIRROR............................................ (a)
IRIS ADJUST D B.................................. (b)
TINT ADJUST G R.................................. ( c )
V POSITION +000..................................... (d)
H POSITION +000..................................... (e)
EXIT
TAKE A PHOTO AND RELEASE
: BRAKE OR SERVICE SW
SELECT SW : CHOOSE ENTER SW : ENTER 
						

							Page 52 (c) TINT ADUST
This setting is used to adjust the colour tint of the image.
The colour tint of the image is automatically adjusted to the optimum
value by the system, but this item allows the colour tint level to be set
manually.
Select this item and press the ENTER button. Use the Select UP/DOWN
switch to increase or decrease the red tint. The red tint can be increased
or decreased by three levels each.
Press the ENTER button to store the new setting and to exit this mode.
(d) V POSITION
This setting is used to set the vertical position of the camera view.
Select this item and press the ENTER button. Use the Select UP/DOWN
switch to move the camera view up or down.
Press the ENTER button to store the new setting and to exit this mode.
(e) H POSITION
This setting is used to set the horizontal position of the camera view.
Select this item and press the ENTER button. Use the Select UP/DOWN
switch to move the camera view left or right.
Press the ENTER button to store the new setting and to exit this mode.
•Select EXIT and press the Select Button to return to the I/O Test Screen.
Adjustment of the Camera
Adjust the camera to obtain the best image by following the steps below.
(1) Verify moving images.
Make sure that the image in the test screen box is moving. If a still picture
is shown press the Brake Pedal once.
(2) Adjust the image quality.
Check the brightness and colour tint of the image and if neccessary adjust
by following steps (b) and (c) above.
(3) Adjust the position.
Make any adjustments neccessary by following steps (d) and (e) above.
To set the position for the average height try to set the position of the
camera as shown below.
(4) Check the image.
Sit in the seat and step om the Brake Pedal. Check the quality and
position of the still image. If the image is not correct, step on the Brake
Pedal and follow repeat steps 2 and 3 above.
Facial picture frame
Seat speakers 
						

							Page 53 6-3-4 Monitor Test
1. Select “MONITOR TEST” on the menu screen to test and adjust the
Monitor. The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press
the Enter button. To return to the Monitor Test Menu from a test pattern
press the Enter button.
3. Select “EXIT” and press the Enter button to return to the menu screen.
Note:   Items (c) and (i) are not used on this game.
MONITOR TEST
GRADATION PATTERN..................................... (a)
CROSSHATCH PATTERN (CRT)..................................... (b)
CROSSHATCH PATTERN (PROJ)..................................... ( c )
WHITE WINDOW (H)..................................... (d)
WHITE WINDOW (M)..................................... (e)
WHITE WINDOW (L)..................................... ( f )
INTERLACE PATTERN..................................... (g)
VIEW ANGLE ADJUST (CRT)..................................... (h)
VIEW ANGLE ADJUST (PROJ)..................................... (i)
FULL WHITE..................................... ( j )
EXIT
SELECT SW : CHOOSE ENTER SW : ENTER
6-3-3-5 Lamp Test
1. Select ‘LAMP TEST’ from the I/O Test Screen. The following screen
is displayed:-
(a) The View Change lamp will turn On or OFF each time the Enter
switch is pressed, and the display will change from OFF to ON.I/O TEST
DIP 4
12345678 [ON:RED]
LINKON  04+1
LAMP TEST
VIEW CHANGE  OFF............................................ (a)
EXIT
SELECT SW : CHOOSE ENTER SW : ENTER 
						

							Page 54 6-3-5 Sound Test
1. Select “SOUND TEST” on the menu screen to test the audio and adjust
the volume settings. The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press
the Enter button.
3. Use the Up/Down switch to change the setting.
4. Press the Enter button to return to item select mode
4. Select “EXIT” and press the Enter button to return to the menu screen.
SOUND TEST

GAME VOLUME
AUTO SETTING............................................. (a)
FRONT L&R SP............................................. (b)
FRONT L SP (0~64) 40......................................... ( c )
FRONT R SP (0~64) 40......................................... (d)
REAR L&R SP............................................. (e)
REAR L SP (0~64) 30......................................... ( f )
REAR R SP (0~64) 30......................................... ( g )
ATTRACT VOLUME
AUTO SETTING............................................. (h)
FRONT L&R SP (0~64) 40......................................... (i)
REAR L&R SP (0~64) 30......................................... ( j )
REQUEST SONG NO. 0000..................................... ( k )
MESSAGE :............................................. (l)
EXIT
ENTER : ENTER SW CHOOSE : SELECT SWITCH
REQUEST : SERVICE SW 
						

							Page 55 (a) AUTO SETTING
The volume levels of all speakers will be adjusted at the same time
with the balance between front and rear speakers being set
automatically.
(b) FRONT L&R SP
The volume levels for both front speakers will be adjusted together.
(c) FRONT L SP [0~64, DEFAULT = 40]
The volume level for the front left speaker only will be adjusted.
(d) FRONT R SP [0~64, DEFAULT = 40]
The volume level for the front right speaker only will be adjusted.
(e) REAR L&R SP
The volume levels for both rear speakers will be adjusted together.
(f) REAR L SP [0~64, DEFAULT = 30]
The volume level for the rear left speaker only will be adjusted.
(g) REAR R SP [0~64, DEFAULT = 30]
The volume level for the rear right speaker only will be adjusted.
(h) AUTO SETTING
The volume levels of all speakers, during attract mode, will be
adjusted at the same time with the balance between front and rear
speakers being set automatically.
(i) FRONT L&R SP [0~64, DEFAULT = 40]
The volume levels of both front speakers, during attract mode, will be
adjusted together.
(j) REAR L&R SP [0~64, DEFAULT = 30]
The volume levels of both rear speakers, during attract mode, will be
adjusted together.
(k) REQUEST SONG No.
Each number produces a different sound each time the service
button is pressed. (The sound will turn off after approx 10 seconds)
Number 001 will produce a stereo test. Sound will be produced from
the left speaker then the right speaker and then both speakers, first
from the cabinet speakers and then from the seat speakers.
The message on the screen will display which speaker is active. 
						

							Page 56
6-3-6 ADS Data
By selecting ADS Data from the menu screen, all of the bookkeeping 
details can be read and/or reset.
6-3-7 Others 1. Select “OTHERS” on the menu screen. The following screen is displa\
yed. 
2. Use the Select Up/Down switch choose the required item then press the Enter button.
3. Select “EXIT” and press the Enter button to return to the menu scr\
een. 
(a,) Displays game software version. 
(b) The current time is displayed (the time cannot be reset)
(c) Used to test the PCB. (this function is only for factory testing)
(d) Sets the language displayed on the screen. (English:ENG, German:GER, French:FRA, Spanish:SPA,Portugese:POR, Italian ITA)
(e) When selected the Data Initialization Menu appears. To reset all game settings to factory setting and clear all stored data , select YES 
from the Data Initialization menu then press the Enter button.
After initializing the backup data ensure that the game is re-
initialized.  (see section 7 page  57)
OTHERS
ROM1 Ver. 97/07/07 MON 21:15:59 .................... (a)
ROM2 Ver. 97/06/27 FRI 20:11:35 
CLOCK 97/08/27 WED 23:11:12 .................... (b)
PCB TEST ......................................... ( c )
LANGUAGE ENGLISH ......................................... (d)
BACKUP MEMORY INITIALIZE ......................................... (e)
EXIT SELECT SW : CHOOSE 
ENTER SW : ENTER 
						

							Page 57
7. INITIALIZATION
Adjustments when Replacing Parts
The following operation 
must always be performed after replacing the Game
PCB, Rom, or Control Potentiometers.
The game will not operate correctly if these adjustments are not made.
1. Slide the TEST switch ON while pressing the SERVICE switch . The
following screen is displayed.
2. Ensure that the steering wheel is set to its centre position and both the
accelerator and brake pedals are released.
3. Press the Service Switch to reset the the numbers displayed on the
screen.
4. Turn the steering wheel fully to the left and then the right.
5. Fully depress and release the accelerator and brake pedals.
6. Press the Enter Switch to store the new limits and to go to Switch Test to
confirm that the steering and pedal controls are working correctly.I/F INITIALIZE
HANDLE +0000
GAS 0000
BRAKE 0000
GO TO [SWITCH TEST] : ENTER
EXIT : DOWN TEST SW 
						

							Page 58
8. MAINTENANCE
G GG G
GAdjustment or maintenance on this machine should be carried out by
qualified personnel only.
Ensure that the 
POWER to the machine is turned OFF before
commencing any maintenance work. (Trouble shooting, service or
repairs etc.)
D DD D
DEinstellungen und Wartung des Gerätes dürfen nur von dafür
qualifiziertem Fachpersonal vorgenommen werden.
Vor Beginn aller Wartungsarbeiten (Fehlersuche, Reparaturen etc.)
muß der Netzstecker gezogen werden.
c cc c
cJusteringer eller vedligehold af denne maskine bør kun udføres af
kvalificeret personale.
Sørg for, at strømmen til maskinen er slukket før der foretages nogen
form for arbejde (fejlfinding, reparation etc.)
E EE E
ELos ajustes y el mantenimiento de esta máquina deben ser realizados
sólo por personal cualificado.
Asegúrese de que la máquina está desconectada antes de comenzar
cualquier trabajo de mantenimiento (reparaciones, resolución de
problemas, etc.)
F FF F
FL’installation, le service, le réglage, ou la maintenance doivent être
effectués uniquement par les personnes qualifiées.
S’assurer que l’interrupteur soit sor OFF avant de commencer tout
travail de maintenance (localisation d’une panne, rèparations, etc.)
K KK K
KÌåôáôñïðÝò Þ åðéäéïñèþóåéò óôá ìç÷áíÞìáôá ðñÝðåé íá ãßíï\
íôáé ìüíï áðü
åîïõóéïäïôçìÝíá Üôïìá.
Íá åßíáé óßãïõñá êëåéóôü ôï ñåýìá ðñéí ïðïéáäÞðïôå äïõëåé\
Ü óôï ìç÷Üíçìá.
I II I
IRegolazioni e manutenzione su questa macchina devono essere fatti
solo da personale specializzato.
Assicurarsi che la macchina sia SPENTA prima di incominciare
qualsiasi lavoro di manutenzione (guasti, riparazioni etc.)
N NN N
NJustering eller vedlikehold på denne maskinen skall bare utføres av
kvalifiserte personell.
Forsikre deg om at strømmen er slått av før du påbegynner noe som
helst vedlikeholdsarbeid (feilsøking, reparasjon osv.) 
						

							Page 59
O OO O
OAanpassingen of onderhoud aan deze machine dient alleen
uitgevoerd te worden door bekwaam personeel.
Zorg ervoor dat de machine UITgeschakeld is voordat er enig
onderhoudswerk wordt verricht (troubleshooting, reparaties etc.)
P PP P
PAfinações ou manutenção nesta maquina, deverão ser efectuadas
sómente por pessoal qualificado.
Certifique-se que a maquina se encontra desligada sempre que
iniciar qualquer tipo de trabalho de manutenção. (identifação de
avarias, reparação etc.)
S SS S
SJusteringar och underhåll på denna maskin skall endast utföras av
kvalificerad personal.
Försäkra dig om att strömmen är avstängd innan underhållsarbete
påbörjas (felsökning, reparationer etc.)
l ll l
lTätä laitetta saa säätää tai huoltaa vain siihen ammattipätevyyden
omaava henkilökunta.
Varmista, että laite on kytketty POIS PÄÄLTÄ ennen työn aloittamista. 
						

							Page 60 8-1 Replacing the Steering PCB and/or Fuse
1. Remove 2off security screw (M5x12) and lower the steering PCB tray.
2. Replace the fuse.
OR
3. Disconnect the connectors.
4. Replace the steering PCB.
5. Raise the steering PCB door and refit the 2off security screw (M5x12).