Namco Point Blank 2 Operators Manual

Page 31
This equipment is fitted with castors to make it easier to move. Take care when
The overall height of this equipment is 2080mm.  Take care of any overhead
W ARNING  •  NEVER turn the power to the machine ON until ins tallation
Notes on Installation
NOTE   •  If the location site of this machine has a polished floor it is 

Page 32
DIESES GERÄT IST NUR FÜR DIE GEWERBLICHE AUFSTELLUNG IN
GESCHLOSSENEN RÄUMEN BESTIMMT.
DAS GERÄT DARF AN FOLGENDEN PLÄTZEN NICHT AUFGESTELLT WERDEN
1. Im Freien.
2. In direktem Sonnenschein, an extrem feuchten und staubigen Plätzen, an Plätzen mit
Wasseranschlüssen und möglichen Leckagen, nahe Klima- und Heizungsanlagen, an
Plätzen mit extrem hohen oder niedrigen Temperaturen.
3. In der Nähe von Notausgängen oder Feuerlöschgeräten.
4. An unstabilen Plätzen oder Plätzen mit übermäßiger Vibration....

Page 33
DENNE MASKINEN ER BARE KONSTRUERT FOR INNENDØRS BRUK
IKKE INSTALLER MASKINEN PÅ FØLGENDE PLASSER.
1. Utendørs
2. Konstant sollys, plasser med mye fuktighet og støv, plasser hvor det er vannlekasje,
nære luft kjølere eller varme elementer, plasser med overdreven høy eller lav temperatur.
3. Plasser hvor det vill stå i veien for nødutganger eller brannslukking utstyr.
4. Ustabile plasser eller plasser med overdreven vibrasjon.
5. Plasser som ikke er i vater.
 DEZE MACHINE IS ALLEEN VOOR GEBRUIK...

Page 34
ESTA MAQUINA FOI CONCEBIDA PARA UTILIZAÇÃO EM ESPACOS
INTERIORES APENAS
NÃO INSTALAR A MAQUINAS NOS SEGUINTES LOCAIS:-
1. Exteriores.
2. `Luz solar directa, locais com humidade excessiva ou pó, locais aonde existam fugas de
água perto de ar condicionados ou equipamentos calorificos e locais com temperaturas
excessivamente quentes ou frias.
3. Locais aonde ficaria colocada no caminho de saidas de emergência ou equipamentos
extintores de fogo.
4. Locais estruturalmente instaveis ou locais com...

Page 35 3-1 Fitting the Header Assembly
The fitting position of the Header Assembly is high, and it is important that a means of
reaching the height safely, without stretching, is available. (e.g. steps, step stool
etc.)
1. Place the Header Assembly on top of the monitor cabinet.
2. Connect the connector.
3. Fit 2off pozi head screws (M5x20), with flat and spring washers. 

Page 36 3-2 Adjusting the Level Adjusters
1. When the game is in its final position, lower the four (4) level adjusters with a
spanner so that the game is level and all castors are raised from the floor by
approximately 5mm. Tighten the lock nuts with a spanner to ensure that the level
adjusters do not move in game play.
Note: If the location site of this game has a polished floor, it is recommended that
rubber pads are fitted under the level adjusters to prevent the game from sliding
on the floor. 

Page 37
4 ADJUSTMENTS
GG 
GG
GAdjustment or maintenance on this machine should be carried out by 
qualified personnel only.
DD 
DD
DEinstellungen und Wartung des Gerätes dürfen nur von dafür 
qualifiziertem Fachpersonal vorgenommen werden.
ll 
ll
lJusteringer eller vedligehold af denne maskine bør kun udføres af 
kvalificeret personale.
EE 
EE
ELos ajustes y el mantenimiento de esta máquina deben ser realizados sólo 
por personal cualificado.
FF 
FF
FL’installation, le service, le réglage, ou la...

Page 38
4-1 Adjustment Switches
The Adjustment switches are located inside the coin door. 
1. Service Switch. Press this switch to obtain game credits without incrementing the coin meter.
2. Test Switch Slide the test switch ON to enter test mode. 
Test mode allows testing and the changing of game settings.
(Refer to section 4-2  Test Mode  page 39)
3. Volume Controls These controls are used to control the sound volume for the Left and Right
Speakers.
COIN COUNTER
TEST SERVICE
2 Amp Q/B 
(Coin Fuse)...

Page 39 4-2 Test Mode
1. Open the coin door and slide the test switch “ON”. The “Menu Screen” will be
displayed on the monitor.
2. Pressing the Player 1 switch will step through the tests and pressing Player 2
switch will select the test.
3. After testing is completed, select Exit & Save and press P2 Start switch to save
the data of the items changed. The machine exits the test mode and returns to
normal game operation. Slide the Test switch OFF.
Note: If the test mode is is not ended as described above...

Page 40  4-2-1 Coin Options
1. Select the option to be changed by pressing the Player 1 Start Button.
2. Press the Player 2 Start Button to change the setting value.
3 . Press Player 1 Start Button to select another option or select EXIT and
press the Player 2 Start Button to return to the MENU screen.
Note: No changes will be stored unless EXIT & SAVE is selected from the MENU
Screen.
(a) Coins required for 1 game. (settable 1 ~ 9.)
(b) Coins required to continue another game. (settable 1 ~ 9)
(c) Coins...