Namco Panic Park Operators Manual

							Page 41 6-3 Test Mode
1. Open the coin door and slide the test switch “ON”. The “Menu Screen” will
be displayed on the monitor.
2. Select the test required by using the select up/down switch. The colour of
the selected test will change.
3. Activate the test by pressing the Enter switch. Select “EXIT” in each test
to return to the “Menu Screen”.
4. After testing is completed, slide the test switch to the “OFF” position to
return to normal game mode.
The Test Switch must always be in the “OFF” position for normal game mode.
MENU
COIN OPTIONS............................Used to set the price of play
GAME OPTIONS............................Used to set the game options
I/O TEST............................Used for testing switches, and
control pots
SOUND TEST............................Used for setting the volume
MONITOR TEST............................Used for setting the monitor
ADS DATA............................Used to view bookkeeping
OTHERS............................Used for testing the PCB
The internal battery’s dead......................Only displayed when battery is
faulty (Refer to your Distributor)
SELECT SW  : CHOOSE
ENTER SW : ENTER 
						

							Page 42 6-3-1 Coin Options
1. Select “COIN OPTIONS” on the menu screen to set the game cost
and related settings. The following screen is displayed.
2. Use the Select Up/Down switch choose the required item then press
the Enter button.
3. Use the Enter button to change the setting.
4. Select “EXIT” and press the Enter button to return to the menu
screen.
Note:- The price of play on this machine is set within the Cashflow Coin Mech.
Ensure that the Game Cost is set to 1 Coin 1 Credit.
m e t Ino i t p i r c s e Dtl u a f e D
e e f e m a g r e y a l P - e n O ) a (9 ~ 1 e l b a t t e s - e m a g r e y a l p 1 r o f d e r i u q e r s n i o C
e r a s g n i t t e s d e d n e m m o c e r , d e g n a h c s i ) a ( f I
. ) c ( d n a ) b ( r o f n w o h s y l l a c i t a m o t u a1
e e f e m a G h c t a M ) b (8 1 ~ 1 e l b a t t e s - e m a G h c t a M a r o f d e r i u q e r s n i o C
s i ) c ( r o f s g n i t t e s d e d n e m m o c e r , d e g n a h c s i ) b ( f I
. n w o h s y l l a c i t a m o t u a
r e y a l p 1 a n a h t s s e l e b t o n n a c e m a g h c t a m r o f e e f e h T
e m a g r e y a l p 1 a f o t s o c e h t e l b u o d n a h t r e h g i h r o n e m a g2
e e f y a l P d e d n e t x E ) c (8 1 ~ 1 e l b a t t e s - e m a G h c t a M a r o f d e r i u q e r s n i o C
e h t n a h t r e h g i h t e s e b t o n n a c y a l p d e d n e t x e r o f e e f e h T
. e m a g h c t a m a r o f e e f1
y a l P e e r F ) d (N O / F F O
y b d e t c e l e s s i e d o m g n i K c i n a P , N O t e s s i y a l p e e r f f I
. s d n o c e s 2 r o f n o t t u b t h g i r r o t f e l e h t g n i d l o hF F O
COIN OPTIONS 
GAME COST (1P)1 COIN (S) 1 CREDIT.........................(a)
GAME COST (2P)1 COIN (S) 1 CREDIT.........................(b)
CONTINUE COST (2P)1 COIN (S) 1 CREDIT.........................(c)
FREE PLAYOFF............................ (d)
EXIT
SELECT SW : CHOOSE
ENTER SW : ENTER 
						

							Page 43 6-3-2 Game Options
1. Select “GAME OPTIONS” on the menu screen to set the game
variables, the following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then
press the Enter button.
3. Use the Enter button to change the setting.
4. Select “EXIT” and press the Enter button to return to the menu
screen.
GAME OPTIONS
[DEFAULT IN GREEN]
NO. OF GAMES (1P) 5............................. (a)
NO. OF GAMES (2P) 5............................. (b)
NO. OF GAMES (2P CONTINUE) 3............................. ( c )
ENTRY WAIT 15........................... (d)
ENTRY WAIT (CONTINUE) 15........................... (e)
ATTRACT SOUND ON......................... ( f )
HI-SCORE INIT (THIS MONTH) NO......................... (g)
YES
HI-SCORE INIT (YEAR) NO......................... (h)
YES
EXIT
SELECT SW : CHOOSE
ENTER SW : ENTER
m e t Ino i t p i r c s e Dtl u a f e D
) a (r o f s e m a g i n i m f o r e b m u N
e m a g r e y a l p e n o a7 , 6 , 5 , 4 , 3
) c ( d n a ) b ( r o f s g n i t t e s d e d n e m m o c e r e h t , d e g n a h c s i ) a ( f I
n w o h s y l l a c i t a m o t u a e r a5
) b (r o f s e m a g i n i m f o r e b m u N
e m a g r e y a l p o w t a7 , 6 , 5 , 4 , 3
s i ) b ( r o f s g n i t t e s d e d n e m m o c e r e h t , d e g n a h c s i ) a ( f I
n w o h s y l l a c i t a m o t u a5
) c (n i s e m a g i n i m f o r e b m u N
y a l p d e d n e t x e7 , 6 , 5 , 4 , 3 , 2 , 0
e l b a l i a v a y a l p d e d n e t x e o N = 03
) d (em i t t i a w y r t n e r e y a l P d n 2sd n o c e s 5 2 , 0 2 , 5 1 , 0 15 1
) e (t i a w y r t n e y a l P d e d n e t x E
e m i ts d n o c e s 5 2 , 0 2 , 5 1 , 0 15 1
) f (ed o m t c a r t t a n i d n u o SFF O / N ON O
) g (e r o c s - i h f o n o i t a z i l a i t i n I
t a ) h t n o m t n e r r u c r o f (
p u - r e w o p) d e z i l a i t i n i e b o t t o n ( O N
) d e z i l a i t i n i e b o t ( S E Y- - -
) h (e r o c s - i h f o n o i t a z i l a i t i n I
p u r e w o p t a ) r a e y e h t r o f () d e z i l a i t i n i e b o t t o n ( O N
) d e z i l a i t i n i e b o t ( S E Y- - - 
						

							Page 44
6-3-3 I/O Test
1. Select “I/O TEST” on the menu screen to test the switches and lamp\
s. The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press the Enter button to enter the test.
3. Select “EXIT” and press the Enter button to return to the menu scr\
een.
I/O TEST
DIP 4
12345678 [ON:RED].............................................. (a)
I/O PCB CHECK ............................................ (b)
I/F INITIALIZE ............................................ ( c )
SWITCH TEST ............................................ (d)
LAMP TEST ............................................ (e)
EXIT SELECT SW : CHOOSEENTER SW : ENTER
(a) Shows the condition of the DIP Switches on the PCB. In normal operation all switches are OFF. (If a switch is ON, it will be displayed in red.)\
(b) Checks function of I/O PCB. 
(c ) Initialize lever potentiometers.  
(see Section 7 page 50)
(e) Selecting this item allows all switches to be checked.
(See 6-3-3-3 page  46)
(f) Selecting this item allows the testing of the start button lamps. (See 6-3-3-4 page  47) 
						

							Page 45 6-3-3-1 I/O PCB Check
1. Select ‘I/O PCB CHECK’ from the I/O Test Screen. The following
screen is displayed:-
6-3-3-2 I/F Initialize
1. Select ‘I/F INITIALIZE’ from the I/O Test Screen to initialize the swing
lever potentiometers.
2. Move both levers fully to their left and press the start button. Repeat
with both levers fully right and then both levers in the centre of their
travel.
Note: Do not force the levers to the left or right as the rubber
bumpers will be compressed and give a false reading.
I/O TEST
DIP 4
12345678 [ON:RED]
LINKON 2
I/O PCB CHECK
Master TX 3536 NAMCO LTD.
PANIC PARK ; Ver1.00 ; JPN
1/0 PCB CONNECT OK NAMCO LTD.
ASCA-4
EXIT
ENTER SW : ENTER 
						

							Page 46 6-3-3-3 Switch Test
1. Select “Switch Test” on the I/O menu screen to test the switches.
The following screen is displayed.
2. The display shows the current state of the switches.
3. Press the Up Select switch and the Enter switch together to EXIT and
return to the I/O menu screen
(a) Numbers change by moving the left lever
(b) Numbers change by moving the right lever
(c,d) The display will change from OFF to ON as each switch is
operated
.
(e) not used .
(f to j) The display will change from OFF to ON as each switch is
operated.
I/O TEST
DIP 4
123456787 [ON/RED]
SWITCH TEST
LEVER (L) 0000................................. (a)
LEVER (R) 0000................................. (b)
SWITCH (L) OFF................................. ( c )
SWITCH (R) OFF................................. (d)
COIN 0................................. (e)
SERVICE OFF................................. (f)
TEST ON................................. (g)
UP SELECT OFF................................. (h)
DOWN SELECT OFF................................. (i)
ENTER OFF.................................. (j)
UP SELECT SW + ENTER SW : EXIT 
						

							Page 47 6-3-3-4 Lamp Test
1. Select ‘LAMP TEST’ from the I/O Test Screen. The following screen
is displayed:-
The start button lamp will illuminate each time the start switch is
pressed and the display will change from OFF to ON.I/O TEST
DIP 4
12345678 [ON:RED]
BUTTON LAMP (L) OFF....................................... (a)
BUTTON LAMP (R) OFF....................................... (b)
EXIT
ENTER SW : ENTER
6-3-4 Monitor Test
1. Select “MONITOR TEST” on the menu screen to test and adjust the
Monitor. The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press
the Enter button. To return to the Monitor Test Menu from a test pattern
press the Enter button.
3. Select “EXIT” and press the Enter button to return to the menu screen.
MONITOR TEST
GRADATION PATTERN..................................... (a)
CROSSHATCH PATTERN (CRT)..................................... (b)
CROSSHATCH PATTERN (PROJ)..................................... ( c )
WHITE WINDOW (H)..................................... (d)
WHITE WINDOW (M)..................................... (e)
WHITE WINDOW (L)..................................... (f)
INTERLACE PATTERN..................................... (g)
VIEW ANGLE ADJUST (CRT)..................................... (h)
VIEW ANGLE ADJUST (PROJ)..................................... (i)
FULL WHITE..................................... (j)
EXIT
SELECT SW : CHOOSE
ENTER SW : ENTER
Note:   Items (c) and (i) are not used on this game. 
						

							Page 48 6-3-5 Sound Test
1. Select “SOUND TEST” on the menu screen to test the audio and adjust
the volume settings. The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press
the Enter button.
3. Use the Up/Down switch to change the setting.
4. Select “EXIT” and press the Enter button to return to the menu screen.
SOUND TEST

VOLUME FRONT L SP (0~64) 45.................................... (a)
FRONT R SP (0~64) 45.................................... (b)
REQUEST SONG NO. 000.................................. ( c )
MESSAGE :........................................ (d)
EXIT
SERVICE SWITCH : REQUEST ON/OFF
SELECT SW : CHOOSE
ENTER SW : ENTER
(a) Volume setting for left channel speaker. Settable from 0 ~ 64 with 0
quietest and 64 loudest.
(b) Volume setting for right channel speaker. Settable from 0 ~ 64 with 0
quietest and 64 loudest.
(c,) Each number will produce a different sound each time the Service
button is pressed. (for a maximum of ten seconds)
001 when selected will produce a sound from the left speaker only,
then the right speaker only and then both speakers together as a
stereo check. The message field shows which speaker is active.
(d) Displays the song No. details. 
						

							Page 49
6-3-6 ADS Data
By selecting ADS Data from the menu screen, all of the bookkeeping 
details can be read and/or reset.
6-3-7 Others 1. Select “OTHERS” on the menu screen. The following screen is displa\
yed. 
2. Use the Select Up/Down switch choose the required item then press the Enter button.
3. Select “EXIT” and press the Enter button to return to the menu scr\
een. 
(a,) Displays game software version. 
(b) The current time is displayed (the time cannot be reset)
(c) Used to test the PCB. (this function is only for factory testing)
(d) Sets the language displayed on the screen. (English:ENG, German:GER, French:FRA, Spanish:SPA,Portugese:POR, Italian ITA)
(e) When selected the Data Initialization Menu appears. To reset all game settings to factory setting and clear all stored data , select YES 
from the Data Initialization menu then press the Enter button.
After initializing the backup data ensure that the game is re-
initialized.  (see section 7 page  50)
OTHERS
ROM1 Ver. 97/07/07 MON 21:15:59 .................... (a)
ROM2 Ver. 97/06/27 FRI 20:11:35 
CLOCK 97/08/27 WED 23:11:12 .................... (b)
PCB TEST ......................................... ( c )
LANGUAGE ENGLISH ......................................... (d)
BACKUP MEMORY INITIALIZE ......................................... (e)
EXIT SELECT SW : CHOOSE 
ENTER SW : ENTER 
						

							Page 50
7. INITIALIZATION
Adjustments when Replacing Parts
The following operation 
must always be performed after replacing the Game
PCB, Rom, or Control Potentiometers.
The game will not operate correctly if these adjustments are not made.
Note: Do not force the levers to the left or right as the rubber bumpers
will be compressed and give a false reading.
1. Slide the TEST switch ON while pressing the SERVICE switch or enter I/F
INITIALIZE from the I/O TEST. The following screen is displayed.
2. Move both levers fully left and press either the left or right start button.
3. Move both levers fully right and press either the left or right start button.I/F INITIALIZE
DIP
12345678[ON:OFF]
MOVE BOTH JOYSTICKS LEFT,
THEN PRESS BUTTON.
[L] 0000 [R] 0000
EXIT
SELECT SW : CHOOSE
ENTER SW : ENTER
I/F INITIALIZE
DIP
12345678[ON:OFF]
MOVE BOTH JOYSTICKS LEFT,
THEN PRESS BUTTON.
[L] 0000 [R] 0000
MOVE BOTH JOYSTICKS RIGHT,
THEN PRESS BUTTON
[R] 0000 [L] 0000
EXIT
SELECT SW : CHOOSE
ENTER SW : ENTER