Namco Gun Survivor 2 Operators Manual

Page 51 6-2-6 Sound Test
1. Select “SOUND TEST” on the menu screen to check the sound and to adjust the
volume. The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item, then press the Enter
button.
3. Use the Select Up/Down switch to change the setting.
4. Press the Enter button to return to the select mode.
5. Select “EXIT” and press the Enter button to return to the ‘Game Options’ screen.
(a) Volume setting for sound during Play Mode. Settable between 000~127...

Page 52 6-2-7 ADS Data
1. Select “ADS DATA” on the menu screen to view bookkeeping details. The
following scren is displayed.
2. Use the Select Up/Down switch to choose the required item, then press the Enter
button.
3. Select “EXIT” and press the Enter button to return to the Game Options Menu
Screen.
(a) Displays the total time the game has been switched on.
(b) Displays the total time the game has been played.
(c) Displays the length of the average playing time.
(d) Displays the ratio between the...

Page 53 6-2-8 Others
1. Select “OTHERS” on the m,enu scren to check the software version, set the on
screen instruction language and reset all adjustments to factory default. The
following screen is displayed.
2. Use the Up/Down Select switch to choose the required item, then press the Enter
button.
3. Select “EXIT” and press the Enter button to return to the Game Options Menu
Screen.
(a) Displays the current software version.
(b) Displays the PCB internal clock settings. (not used on this game)
(c)...

Page 54
7. MAINTENANCE
  
Adjustment or maintenance on this machine should be carried out by
qualified personnel only.
Ensure that the 
POWER to the machine is turned OFF before commencing
any maintenance work. (Trouble shooting, service or repairs etc.)
  
Einstellungen und Wartung des Gerätes dürfen nur von dafür qualifiziertem
Fachpersonal vorgenommen werden.
Vor Beginn aller Wartungsarbeiten (Fehlersuche, Reparaturen etc.) muß der
Netzstecker gezogen werden.

 

 


Justeringer eller...

Page 55
  
Aanpassingen of onderhoud aan deze machine dient alleen uitgevoerd te
worden door bekwaam personeel.
Zorg ervoor dat de machine UITgeschakeld is voordat er enig
onderhoudswerk wordt verricht (troubleshooting, reparaties etc.)
  
Afinações ou manutenção nesta maquina, deverão ser efectuadas sómente
por pessoal qualificado.
Certifique-se que a maquina se encontra desligada sempre que iniciar
qualquer tipo de trabalho de manutenção. (identifação de avarias,
reparação etc.)...

Page 56 7-1 Greasing the Gun Assy
The Gun Assembly should be checked for correct operation daily.
The gun Assembly should be re-greased every 6 months.
1. Remove 6off security screw (M6x16), 1off security screw (M6x16), with flat
washer, and remove the Front Vac-Form.
2. Apply grease to the areas shown below.
Use silicon grease Part No. 95000018
3. Reassemble in reverse order.
Security screw (M6x16)
Security screw (M6x16) Security screw (M6x16)
Flat washer
Front Vac-Form 

Page 57 7-2 Removing the Gun Assy
1. Remove 4off security screw (M6x20), with flat washer.
2. Remove the Top Vac-Form by lifting it up and over the Gun Assy.
Flat washer
Security screw (M6x20)
Top Vac-Form
Security screw (M6x20)Security screw (M6x20)
Top Vac-Form 

Page 58 3. Remove 6off security screw (m6x16) and remove the Front Vac-Form.
4. Remove 40ff pozi head screw (M6x35) and remove the Gun Assy Cover.
Security screw (M6x16)
Security screw (M6x16)
Front Vac-Form
Pozi head screw (M6x35)Pozi head screw (M6x35)
Gun Assy Cover 

Page 59 5. Remove the 2off upper security screws (M6x20), slacken the 2off lower security
screws (M6x20) and remove the Rear Access Panel.
6. Remove 1off hex head screw (M8x35), with flat washer.
Security screw (M6x20)
Security screw (M6x20) (loosen) Rear Access Panel
Flat washer
Hex head screw (M8x35) 

Page 60
7. Disconnect the connector.
8. Remove 2off hex head screws (M8x25), with flat washers, and withdraw the Gun
Assy while lifting up the Gun Assy Cover.
9. Reassemble in reverse order.
Note: After refitting the Gun Assy ensure that the Gun is reinitialized. (see 6-2-4-2 page 47)
Gun Assy Cover
Hex head screw (M8x25)
Flat washer
Gun Assy
Connector