Namco Final Furlong 2 Conversion Instructions

Replacing the Game PCB
1. Disconnect all the connectors on the Game PCB including the fan connectors.
Note:  Some of the cables will be replaced with new cables (see illustration below)
2. Remove the 2off pozi head screws (M6x25) from the right hand end of the Game
PCB. slacken the 2off pozi head screws (M6x25) on the left hand end and remove
the Game PCB.
These cables
will not be used
on the new 
game PCB
Pozi head screw
(M6x25) 

3. Place the old and new game PCBs next to each other.
4. Remove 8off pozi head screws (M4x50) and remove the fans from the old Game
PCB. (4 screws on each fan).
5. Fit the fans to the new Game PCB in 
exactly the same way up using 4off pozi head
screws (M4x50). (2 screws on each fan).
THESE FANS MUST BE FITTED TO THE NEW GAME PCB
OR IRREPERABLE DAMAGE WILL BE CAUSED TO THE
NEW GAME PCB.
Pozi head screw
(M6x25)
Pozihead screw (M4x50) 

6. Refit the new Game PCB and fully tighten the 4off pozi head screws (Mx25).
7. Connect the new cables linking the I/O boards to the Front Cover Boards, and the
new HSB cable linking the two front cover boards.
8. Locate and separate the two way connector with yellow and black wires. This is
located to the right of the Switchmode Power Supply.
9. Fit the new break out cable to the two way connectors and connect the other ends to
the front cover boards, as shown in the diagram below. 

10. Refit the existing connectors to the I/O Boards and Front Cover Boards.
Note: When refitting the D Sub connectors to the Front Boards ensure that connector 2
is fitted to the board nearest the rear of the cabinet, and the connector retaining
screws are fully tightened.
D Sub #1
D Sub #2 

Replacing the Repeater (Link) PCB
1. Remove 1off pozi head screw (M5x12) and remove the Link Cover Bracket.
2. Remove 2off Pozi head screws (M4x12) and remove the Link PCB complete with
mounting bracket.
3. Disconnect the connectors.
Link cover
Pozi head screw (M5x12
Pozi head screw
(M4x12) 

4. Refit the new Link PCB complete with mounting bracket using the 2off pozi head
screws (M4x12).
5. Fit the new Communication cable.
Pozi head screw
(M4x12) 

RE-ASSEMBLY AND TEST
1. Reasemble the Ride Assemblies to the Monitor Cabinet, taking care not to trap any
wires.
2. Reconnect the Mains-In and switch ON.
3. Reinitialize both players. (see section 6-8 page 58 of the Operators Manual).
4. Reset all game settings to the required levels. (see section 6-7 ‘Test Mode’ page 47 of
the Operators Manual).
CONVERSION IS NOW COMPLETE. 

NEW PART NUMBERS
m e t Ino i t p i r c s e DoN t r a P
4)S H L ( l a c e D e d i S t e n i b a C 2 F F0 1 8 - 2 9 6
5)S H R ( l a c e D e d i S t e n i b a C 2 F F1 1 8 - 2 9 6
6la c e D ) A ( n o i t c u r t s n I 2 F F6 9 8 - 2 9 6
7la c e D ) A ( t n o r F t e n i b a C 2 F F5 1 8 - 2 9 6
8la c e D r e p p U m r o F - c a V r o t i n o M 2 F F3 2 8 - 2 9 6
9la c e D r e w o L m r o F - c a V r o t i n o M 2 F F8 9 8 - 2 9 6
0 1la c e D ) B ( t n o r F t e n i b a C 2 F F6 1 8 - 2 9 6
1 1la c e D ) C (...

1
(Opposite side 2)
3
m e t Ino i t p i r c s e DoN t r a P
1)S H R ( l a c e D r a e R e s r o H3 4 8 - 2 9 6
2)S H L ( l a c e D r a e R e s r o H2 4 8 - 2 9 6
3la c e D e s a B 2 F F0 5 8 - 2 9 6
m e t Ino i t p i r c s e DoN t r a P
4re v o C s s u r T1 6 8 - 2 9 6
6re v o C d r a o b n g i S 2 F F0 6 8 - 2 9 6
7la c e D o g o L e r t n e C3 6 8 - 2 9 6
4 1et a l P t h g i L2 6 8 - 2 9 6