Namco Final Furlong 2 Conversion Instructions

							FINAL FURLONG 2
CONVERSION INSTRUCTIONS 
						

							It is most important that the game is tested and any problems
rectified before any conversion work is started.
Please make a note of all setting values so that the new Game
PCB can be set accordingly.
Warning: Ensure that the game is switched off and disconnected from the
mains supply before any conversion work is started.
Caution: Ensure adequate space is available to able to remove the header
safely.
Note: Take care when removing items not to lose any screws and washers as
they may be required for reassembly.
Tools Required:-
No1 Pozi Driver
No2 Pozi Driver
Security Wrench for M5
Spanner for M10
Spanner for M20
Security Torx Wrench for M5 (Supplied in kit) 
						

							PRELIMINARY
Removing the Ride Assembly
1. Raise the twelve adjustable feet, (4 on the monitor cabinet and 4 on each ride base
assy), (Slacken the lock nuts with a spanner first.)
2. Remove 8off security screws (M5x12) and remove both Base Front Cover Plates.
3. Remove 4off hex head screws (M10x35), with flat and spring washers, retaining the
ride base to the monitor cabinet. 
						

							4. Pull the ride assembly away from the monitor cabinet only sufficient to reach the
connectors. (
Take care not to stretch the wiring harness.)
5. Disconnect the connectors and move the ride assembly completely away from the
monitor cabinet.
Removing the Header Assembly
The header assembly is high and has a forward centre of gravity, so it is important
that at least 
two people are used to remove or fit the Header Assembly.
1. Remove 2off pozi head screws (M4x12), with flat and spring washers, and remove
the connector cover plate.
2. Disconnect the connector. 
						

							3. Remove 2off pozi head screws (M5x16), with flat and spring washers.
4. Slide the header assembly forward so that it disengages with the retaining bracket.
5. Remove the Header Assembly 
						

							RIDE ASSEMBLY
DECALS
1. Remove the Horse Rear Decals (both sides of the horse).
2. Fit the new Horse Rear Decals (both sides of the horse).
3. Fit the new decals to the rear of the Ride Base.
Replace (Both sides)
New Decals 
						

							HEADER ASSEMBLY
1. Remove the ten security screws (M5x16) and remove the header acrylic. (This part is
no longer required).
2. Remove 2off pozi head screw (M4x12) and remove the Top Bracket. (This part is no
longer required).
Pozihead screw
(M4x12) 
						

							3. Fit the new top brackets with 4off torx security screws (M5x12 black), supplied.
4. Fit the new Header Acrylic with 10off torx security screw (M5x16 chrome), supplied.
5. Refit the Header Assembly.
6. Reconnect the connector.
7. Refit the Connector Cover Plate.
Torx security screw
(M5x12 black)
Torx security screw
(M5x16 chrome)
Torx security screw
(M5x16 chrome)
Torx security screw
(M5x16 chrome) 
						

							MONITOR CABINET
Replacing the Decals
1. Remove all the old decals, except the Monitor Middle Lower Decal.
2. Fit the new decals as shown below.
Remove
RemoveRemove
(both sides) DO NOT REMOVE
Remove
New
NewNew
(both sides)
New
New
New 
						

							Fitting the New Front Vac-Form
1. Fit the new Vac-Form Bracket with 2off torx security screw (M5x16 black), supplied.
2. Fit the new Vac-Form with 4off Torx security screw (M5x16 black), supplied.
Torx security screw
(M5x16 black)
Torx security screw
(M5x16 black)