Home > Namco > Games > Namco Downhill Biker Operators Manual

Namco Downhill Biker Operators Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Namco Downhill Biker Operators Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 93 Namco manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Page 43 If there is a failure of one game PCB, fit the link cables as shown below to
    isolate the faulty unit and allow the other PCB(s) to operate correctly. 
    						
    							Page 44
    6. ADJUSTMENTS
    G GG G
    GAdjustment or maintenance on this machine should be carried out by
    qualified personnel only.
    D DD D
    DAufstellung, Service, Einstellung und Wartung dürfen nur von dafür
    qualifiziertem Fachpersonal durchgeführt werden.
    l ll l
    lJusteringer eller vedligehold af denne maskine bør kun udføres af
    kvalificeret personale.
    E EE E
    ELos ajustes y el mantenimiento de esta máquina deben ser realizados
    sólo por personal cualificado.
    F FF F
    FL’installation, le service, le réglage, ou la maintenance doivent être
    effectués uniquement par les personnes qualifiées.
    K KK K
    KÌåôáôñïðÝò Þ åðéäéïñèþóåéò óôá ìç÷áíÞìáôá ðñÝðåé íá ãßíï\
    íôáé ìüíï áðü
    åîïõóéïäïôçìÝíá Üôïìá.
    I II I
    IRegolazioni e manutenzione su questa macchina devono essere fatti
    solo da personale specializzato.
    N NN N
    NJustering eller vedlikehold på denne maskinen skall bare utføres av
    kvalifiserte personell.
    O OO O
    OAanpassingen of onderhoud aan deze machine dient alleen
    uitgevoerd te worden door bekwaam personeel.
    P PP P
    PAfinações ou manutenção nesta maquina, deverão ser efectuadas
    sómente por pessoal qualificado.
    S SS S
    SJusteringar och underhåll på denna maskin skall endast utföras av
    kvalificerad personal.
    l ll l
    lTätä laitetta saa säätää tai huoltaa vain siihen ammattipätevyyden
    omaava henkilökunta.
    6-1 Turning on the Power
    After the machine has been installed, turn ON the power. The power
    switch is located on the rear of the monitor cabinet. 
    						
    							Page 45
    6-2 Adjustment Switches
    The Adjustment switches are located inside the coin door. 
    1. Service Switch. Press this switch to obtain game credits without incrementing the play 
    meter.
    2. Test Switch Slide the test switch ON to enter test mode.
    Test mode allows testing and the changing of game settings. (Refer to
    section 6-3  Test Mode page  46)
    3. Select Up/Down Switch This switch is used to select the test required when in the Test Mode.
    4. Enter Switch This switch is used to enter a selected test and to change settings with\
    in
    a test.
    COIN COUNTER
    TEST SER VICE
    SELECTSELECT
    TEST SERVICE
    UP
    SELECT DOWN
    UP
    SELECT DOWN 2 Amp Q/B 
    (Coin Fuse)
    PLAYER 1 PLAYER 2 
    						
    							Page 46 6-3 Test Mode
    1. Open the coin door and slide the test switch “ON”. The “Menu Screen” will
    be displayed on the monitor.
    2. Select the test required by using the select up/down switch. The colour of
    the selected test will change.
    3. Activate the test by pressing the Enter switch. Select “EXIT” in each test
    to return to the “Menu Screen”.
    4. After testing is completed, slide the test switch to the “OFF” position to
    return to normal game mode.
    The Test Switch must always be in the “OFF” position for normal game mode.
    MENU
    COIN OPTIONS............................Used to set the price of play
    GAME OPTIONS............................Used to set the game options
    I/O TEST............................ Used for testing switches,
    lamps, and control pots
    MONITOR TEST............................Used for setting the monitor
    SOUND TEST............................Used for setting the volume
    ADS DATA............................Used to view bookkeeping
    OTHERS............................Used for testing the PCB
    The internal battery’s dead....................... Only displayed if PCB battery
    is faulty
    SELECT SW : CHOOSE  ENTER SW : ENTER 
    						
    							Page 47 6-3-1 Coin Options
    1. Select “COIN OPTIONS” on the menu screen to set the game cost
    and related settings. The following screen is displayed.
    2. Use the Select Up/Down switch to choose the required item then
    press the Enter button.
    3. Use the Up/Down switch to change the setting.
    4. Select “EXIT” and press the Enter button to return to the menu
    screen.
    Note:- The price of play on this machine is set within the Cashflow Coin Mech.
    Ensure that the Game Cost is set to 1 Coin 1 Credit.
    M E T INO I T P I R C S E DTE S Y R O T C A F
    t s o C e m a G ) a (9- 1 e l b a t t e s - - - - - s t i d e r C f o r e b m u n r o f d e r i u q e r s n i o Ct i d e r C 1 n i o C 1
    y a l P e e r F ) b (ff O / n O - - - - - t i d e r c r o f d e r i u q e r s n i o c o NFF O
    COIN OPTIONS
    
    GAME COST 1 COIN (S) 1 CREDIT........................ (a)
    FREE PLAY OFF........................ (b)
    EXIT
    SELECT SW : CHOOSE  ENTER SW : ENTER 
    						
    							Page 48 6-3-2 Game Options
    1. Select “GAME OPTIONS” on the menu screen to set the game
    variables. The following screen is displayed.
    2. Use the Select Up/Down switch to choose the required item then
    press the Enter button.
    3. Use the Up/Down switch to change the setting.
    4. Select “EXIT” and press the Enter button to return to the menu
    screen.
    M E T INO I T P I R C S E DTE S Y R O T C A F
    D I B C P ) a (4- 1 e l b a t t e s - - - - r e b m u n r e y a l p o t r e b m u n B C P s t e S2/ 1
    t i a W y r t n E ) b (e m a g d e k n i l a n i o j o t s r e y a l p r e h t o r o f d e w o l l a d o i r e p e m i T
    s d n o c e s 2 2 , 0 2 , 8 1 , 6 1 , 4 1 , 2 1 , 0 1 , 84 1
    d n u o S t c a r t t A ) c (FF O / N O e d o m t c a r t t a n i d n u o SNO
    e s r u o C d e e p S ) d ()d r a H y r e V ( E o t ) y s a E y r e V ( A)y s a E ( B
    e s r u o C l a c i n h c e T ) e ()d r a H y r e V ( E o t ) y s a E y r e V ( A)y s a E ( B
    ? t i n I e r o c S - i H ) f (ON / S E Y p u r e w o p t a d e z i l a i t i n i e r o c S - i HON
    Note:
    (i) PCB ID numbers are assigned so that they are not duplicated on the
    linked seats. Be sure to set these correctly to avoid link absence or other
    operation faults. PCB ID numbers (1 ~ 4) are matched to the numbers of
    the current players (1P ~ 4P).
    (ii) The same degree of difficulty must be set for all of the linked seats. If
    different degrees of difficulty are set, the machine will not operate
    correctly.
    GAME OPTIONS
    
    PCB ID 1.................................. (a)
    ENTRY WAIT 14.................................. (b)
    ATTRACT SOUND ON.................................. ( c )
    GAME DIFFICULTY
    SPEED C (MEDIUM).................................. (d)
    TECHNICAL E (HARD).................................. (e)
    HI-SCORE INIT NO.................................. ( f )
    EXIT
    SELECT SW : CHOOSE ENTER SW : ENTER 
    						
    							Page 49
    6-3-3 I/O Test
    1. Select “I/O TEST” on the menu screen to switches and lamps. The following screen is displayed.
    2. Use the Select Up/Down switch to choose the required item then press the Enter button to enter the test.
    3. Select “EXIT” and press the Enter button to return to the menu scr\
    een. 
    (a) Shows the condition of the DIP Switches on the PCB. In normal operation all switches are OFF. (If a switch is ON, it will be displayed in red.)
    (b) Shows the number of units linked. (1 ~ 4). If no link data is being received LINK OFF will be displayed. 
    If unrecognisable data is being received LINK NG will be displayed.
    (c) Checks function of I/O PCB. 
    (d ) Instructions to Initialize game.  
    (see Section 7 page 56)
    Note: Initialization cannot be started from this screen
    (e) Selecting this item allows all switches and pedal sensor to be checked. (See 6-3-3-3 page  51)
    (f) Selecting this item allows the testing of the pedal brake and start lamp\
    s. (See 6-3-3-4 page  52)
    I/O TEST
    DIP 4
    12345678 [ON:RED].............................................. (a)
    LINK
    ON 2............................................ (b)
    I/O PCB CHECK ............................................ ( c )
    HOW TO [I/F INITIALIZE] ............................................ (d)
    SWITCH TEST ............................................ (e)
    PEDAL & LAMP TEST ............................................ ( f )
    EXIT
    SELECT SW : CHOOSE ENTER SW : ENTER 
    						
    							Page 50
    6-3-3-1 I/O PCB Check
    1. Select ‘I/O PCB CHECK’ from the I/O Test Screen. The followingscreen is displayed:-
    I/O TEST
    DIP 4
    12345678 [ON:RED]
    LINKON 2
    I/O PCB CHECK
    Master TX 3536 NAMCO LTD. 
    DOWNHILL BIKERS ; Ver1.00 ; JPN
    1/0 PCB CONNECT OK NAMCO LTD.
    ASCA-4
    EXIT
    SELECT SW : CHOOSE ENTER SW : ENTER
    6-3-3-2 How to [I/F Initialize]
    1. Select ‘I/O PCB CHECK’ from the I/O Test Screen. The followingscreen is displayed:-
    Note: This is an instruction screen only . Initialization cannot be performed
    from this screen.  (see Section 7 page  56 for initialization)
    I/O TEST
    DIP 4
    12345678 [ON:RED]
    LINKON 2
    HOW TO [I/F INITIALIZE] 
    I/F INITIALIZE: HOLDING SERVICE SWAND TURN ON TEST SW
    EXIT
    SELECT SW : CHOOSE ENTER SW : ENTER 
    						
    							Page 51
    6-3-3-3 Switch Test
    1. Select “Switch Test” on the I/O menu screen to test the switches. The following screen is displayed.
    2. The display shows the current state of the switches. 
    3. Press the Up Select switch and the Enter switch together to EXIT and return to the I/O menu screen
    (a) Not Used
    (b) The display will change from OFF to ON as each switch is operated.
    (c) The game will return to normal play mode if this switch is turned off.
    (d to i) The display will change from OFF to ON as each switch is operated.
    (j) When you pedal forward “FORWARD” is displayed and the numbers increase. When you pedal backwards “REVERSE” 
    appears and the numbers decrease. The numbers return to
    the starting number each time the pedals are turned a full
    360³
    (k) The numbers increase when the handle bar is turned right and decrease when turned left.” RIGHT OK” and “LEFT OK” is
    displayed when the handle bar is fully left or right. If “RIGHT
    OK” or “LEFT OK” is not displayed, initialize the
    potentiomete r.  (see Section 7 page  56)
    SWITCH TEST
    DIP 4
    123456787 [ON/OFF]
    LINK ON 2 
    SWITCH TEST 
    COIN
    000................................. (a)
    SERVICE
    OFF................................. (b)
    TEST
    ON................................. ( c )
    UP SELECT
    OFF................................. (d)
    DOWN SELECT
    OFF................................. (e)
    ENTER
    OFF................................. ( f )
    BUTTON
    OFF................................. (g)
    BRAKE RIGHT
    OFF................................. (h)
    BRAKE LEFT
    OFF................................. (i)
    PEDAL ENCODER
    000 FOR WARD....................... ( j )
    HANDLE BAR
    +0000 RIGHT OK....................... ( k )
    LEFT OK
    UP SELECT SW + ENTER SW : EXIT 
    						
    							Page 52 6-3-3-4 Pedal & Lamp Test
    1. Select ‘I/O PCB CHECK’ from the I/O Test Screen. The following
    screen is displayed:-
    I/O TEST
    DIP 4
    12345678 [ON:RED]
    LINKON 2
    PEDAL & LAMP TEST
    PEDAL BRAKE
    01 2 3 4
    OFF MIN >>> >>> MAX
    BUTTON LAMP
    ON ......................................................... (b)
    EXIT
    SELECT SW : CHOOSE ENTER SW : ENTER
    (a)
    (a) PEDAL BRAKE (force feedback)
    Press the ENTER button to apply the pedal brake force-feedback in
    five levels (0-4)
    (b) BUTTON LAMP
    The Start Switch lamp will switch on and off each time the ENTER
    button is pressed. 
    						
    All Namco manuals Comments (0)

    Related Manuals for Namco Downhill Biker Operators Manual