Namco Downhill Biker Operators Manual

Page 33
G
DIESES GERÄT IST NUR FÜR DIE GEWERBLICHE AUFSTELLUNG IN
GESCHLOSSENEN RÄUMEN BESTIMMT.
DAS GERÄT DARF AN FOLGENDEN PLÄTZEN NICHT AUFGESTELLT WERDEN
1. Im Freien.
2. In direktem Sonnenschein, an extrem feuchten und staubigen Plätzen, an Plätzen mit
Wasseranschlüssen und möglichen Leckagen, nahe Klima- und Heizungsanlagen, an
Plätzen mit extrem hohen oder niedrigen Temperaturen.
3. In der Nähe von Notausgängen oder Feuerlöschgeräten.
4. An unstabilen Plätzen oder Plätzen mit übermäßiger...

Page 34
F
K
I
N
O
DENNE MASKINEN ER BARE KONSTRUERT FOR INNENDØRS BRUK
IKKE INSTALLER MASKINEN PÅ FØLGENDE PLASSER.
1. Utendørs
2. Konstant sollys, plasser med mye fuktighet og støv, plasser hvor det er vannlekasje,
nære luft kjølere eller varme elementer, plasser med overdreven høy eller lav temperatur.
3. Plasser hvor det vill stå i veien for nødutganger eller brannslukking utstyr.
4. Ustabile plasser eller plasser med overdreven vibrasjon.
5. Plasser som ikke er i vater.
 DEZE MACHINE IS ALLEEN VOOR...

Page 35
P
l S
ESTA MAQUINA FOI CONCEBIDA PARA UTILIZAÇÃO EM ESPACOS
INTERIORES APENAS
NÃO INSTALAR A MAQUINAS NOS SEGUINTES LOCAIS:-
1. Exteriores.
2. `Luz solar directa, locais com humidade excessiva ou pó, locais aonde existam fugas de
água perto de ar condicionados ou equipamentos calorificos e locais com temperaturas
excessivamente quentes ou frias.
3. Locais aonde ficaria colocada no caminho de saidas de emergência ou equipamentos
extintores de fogo.
4. Locais estruturalmente instaveis ou locais com...

Page 36 5-1 Fitting the Header Assembly
The Header Assembly has a forward centre of gravity, so it is important that at
least 
two people are used to fit or remove the Header Assembly.
The fitting position of the Header Assembly is very high, and it is important
that a means of reaching the height safely, without stretching, is available.
(e.g. steps, step stool etc.)
1. Place the header assembly on to the monitor cabinet and connect the
connector.
2. Slide the header assembly back until it engages under...

Page 37 5-2 Fitting the Bike Assy
1. Remove the 4off socket head screws (M8x16), remove the shipping
bracket and rubber pad from each bike, and refit the 4off hex head screws
(M8x16).
2. Remove the 2off security screw (M5x12) and remove the roping bracket
and protective paper on the rear of each bike. Refit the 2off security
screws (M5x12)
3. Place the bikes close to the monitor cabinet and connect the connectors.
Push the ride assembly up to the monitor cabinet, taking care not to trap
any wires or...

Page 38 4. Fit the joint brackets using 4off hex head screws (M8x20).
5. Slacken the 4off hex head screws (M8x20) on the inner side of each bike
so that there is approximately 10mm of thread showing.
6. Remove 4off security screw (M5x12) and remove the cover and end
bracket from the joint box. 

Page 39 7. Fit the joint box between the two bikes so that the slots on the side of the
joint box fit over the hex head screws (M8x20).
8. Tighten the hex head screws to retain the joint box.
9. Place the shipping brackets, rubber pads, roping brackets and protective
papers previously removed into the joint box for future use.
10. Refit the joint box cover and end bracket with the 4off security screws
(M5x12). 

Page 40 11. Fit the connector cover using the 2off security screw (M5x12).
12. When the machine is in its final position, lower the fourteen level
adjusters, (6 on the monitor cabinet and 4 on each ride assy), with a
spanner so that the machine is level and all castors are raised from the
floor by approx. 5mm. Tighten the lock nuts with a spanner to ensure that
the level adjusters do not move.
Note: If the location site of this machine has a polished floor it is recommended
that rubber pads are fitted...

Page 41
5-3 Fitting the Number Decals
When the game has been assembled, fit the number decals to the monitor 
cabinet and each bike. 
The number decals should be fitted in ascending order from the left. 1 GAME - 2 PLAYERS
2 GAMES - 4 PLAYERS
Ensure that the PCB ID is set to match the decal number . (Refer to
Section 6-3-2  Page 48 for PCB ID setting.) Failure to do so may cause the
game to operate incorrectly . 

Page 42 5-4 Linking Games
A single game (2 players) is linked using two short link cables as shown below.
To link two games (4 players):-
1. Remove 2off pozi head screws (M4x12) and remove the link cover
bracket.
2.  Using the longer link cables (supplied) link the two games as shown
below.
3. Refit the link cover bracket with the 2off pozi head screws (M4x12).
Note:- Retain the removed short link cables safely for future use.