Namco Cybersled Operators Manual

Page 22
7-3 The Lever Assy
7-3-1 Removing the Lever Assy
1. Remove the rear cover (B) located at the back of the main body.
2. Disconnect the connector of the lever assy and that of the speaker assy.
3. Remove eight torque bolts (M5 x 12),  then the panel cover.
4. Remove seven cup screws (M5 x 12),  then the control panel cover together
with the lever assy.
5. Disconnect the connectors of the lever assy and the connector of the view
point change button.
6. Remove four cup screws (M6 x 20),  then remove...

Page 23
Left/right volume pot
Philips hex head screw
Backward/forward volume pot
7-3-3 Removing the Grip
1. Remove the four security screws (M5x8) from either side and the philips
head screw (M4x25) and nut.
2. The microswitches are fitted to the same side as then nut.
3. Ensure that the springs are fitted correctly and that no wires are trapped
when re-assembling.
7-3-2 Replacing the Joystick Volume Pots
1. Remove the 4 x Philips hex head screws retaining the volume plate to the
main assy
2. Replace the...

Page 24
7-4 Removing the Control Panel Assy
1. Remove the rear cover (B) located on the back of the  main body.
2. Disconnect all connectors to the control panel assy.
3. Remove the four assembling bolts (M10 X 45).
4. Lift the control panel assy,  unhook and pull the control panel assy forwards
to remove it from the main body. 

Page 25
7-5 Removing the Monitor Bezel
1. Remove the rear cover (B) located on the back of the main body.
2. Loosen the four assembling bolts (M10 X 45) fixing the control panel assy.
(Do not remove them).
3. Remove the four torque bolts (M5 x 20).
4. Lift the monitor bezel upwards and forward to remove it. 

Page 26
8 Illustrated Parts List
8-1 Main Body Assy
3
7
6
8
9
4
15
10
1
16
2 13
14
11
5
12 

Page 27
NoDescriptionQntyPart Number
1Rear Cover (A)1n/a
2Rear Cover (B)1n/a
3Top Flash Bracket288300610
4Front Cover188300612
5Monitor Vac Form - Blue185300621
6Monitor Vac Form - Red185300622
7Marquee Acrylic130000002
8Front Sticker (EX)140000170
9Front Sticker (B)140000173
10Lower Sticker140000171
11Monitor Sticker140000175
12Instructions Sticker (EX)140000176
13Castor459000005
14Adjuster488300079
15Base Floor Connector288300616
16Switching Regulator 5v 30A/12v 7A183000004
As these environmental...

8-2 Control  Panel  Assy
NoDescriptionQntyPart Number
1Control Panel Case188300623
2Control Panel Cover188300624
3
Panel Cover (Blue)188300625
Panel Cover (Red)188300626
4
Control Panel Sticker (LH)140000177
Control Panel Sticker (RH)140000179
Control Panel Sticker (Centre)140000178
5Push Switch160500061
6Speaker162000007 

8-3 Seat Assy
6
7 9
10
8
1
11
53 2
4
13 12
NoDescriptionQntyPart NumberNoDescriptionQntyPart Number
1Base floor188300605
8
Seat  Blue (Left)188300601
2Seat base188300606Seat Red (Right)188300602
3Seat base cover1883006079Speaker plate288300603
4Floor mat18830060910Speaker262000007
5Edge trim28830060811Adjuster288300079
6Back sticker14000018012Castor259000005
7
Seat sticker (blue)140000168
Seat sticker (red)140000169 

8-4 Lever Assy
95-1296-00
95-1297-00
95-1298-00
95-1315-00
95-1295-00
95-1293-00
43-0099-00 43-1294-00
95-1294-00
95-2516-00
95-0160-00
42-0056-00 95-0183-00
95-0028-00
96-4102-00
43-0098-00
95-0166-00
95-7007-0043-0231-00
95-7022-00
43-1003-00
95-7008-00
95-7010-00
95-7021-00
96-4115-00
95-0029-00
95-0013-00
96-4111-00 50-8026-00
95-7011-00
95-7009-00
95-7019-00
90-1204-00
96-4114-00
96-4107-00
95-7047-00 95-7027-0095-7028-00
96-4116-00
42-0117-00 96-4108-00
43-0232-00 

9. T\foubleshooting
If you suspect the game may be malfunctioning,  the following steps should be
conside\fed befo\fe you make a se\fvice \fequest.
1. When some othe\f equipment (ai\f conditione\fs, multiple pinball games,  la\fge Kiddie Rides) a\fe connected to the same powe\f supply,  the voltage may 
fluctuate and cause this game t\fouble o\f imp\fope\f ope\fation.
\b. When the game PCB,  the ROMS,  the leve\f assembly o\f volume cont\fols a\fe \feplaced,  it is necessa\fy to make adjustment fo\f the...